Advertisement
Section 3 - Resetting the Smart Control Receiver
NOTE: The actuator can be detachable to provide different actuating range to match the wall
button or wall console. Pull out the actuator from its position, reverse and re-install to the unit.
1. Press and hold the "PROG" button (1) on the Smart Control Receiver (A) for 5 seconds
until the LED stays Solid.
2. The actuator (2) will reset to the highest position.
A
A
1
NOTE:
Extend or retract the
actuator from its position
to ensure the actuator
2
can make contact with
the wall button to
activate the garage
door.
NOTE:
To extend the actuator, take it out and place it reversed.
To make it shorter, remove the actuator.
Section 8 - Changing the Remote Control Password
1. To change the password, press buttons 1 and 3 simultaneously and hold for at
least 10 seconds. The LED (4) will change from ashing quickly to ashing slowly.
2. Input the old password (factory default 2,2,2).
3. Press buttons 1 and 3 simultaneously to con rm. If the password is wrong,
the LED (4) will ash three times, and you have to restart.
4. Input the new password.
5. Press buttons 1 and 3 simultaneously to con rm.
6. The password has now been changed, and the password protection is now enabled.
B
4
1
2
3
Section 4 - Operating
NOTE: The keychain remote comes with lithium battery installed. Remove the battery isolator
tag from the keychain remote control before using.
1.
Press the programmed button (1) on the keychain remote (B) or press the touch
plate (2) on the Smart Control Receiver (A) to push the wall button which will
open/close the garage door.
A
B
1
2
Section 9 - Resetting the Remote Control Password
NOTE: After resetting the Remote, the password feature will be disabled and the password
will change back to the factory default 2,2,2. You need to re-program the remote
to the Smart Control Receiver again.
1. To reset the password, press buttons 1 and 2 simultaneously and hold for more than
15 seconds until the LED (4) ashes.
2. After you release buttons 1 and 2, the LED (4) will be turned off and the remote will be
reset back to factory default password.
B
4
1
2
3
PACKAGE CONTENTS
Section 5 - Programming the Remote Control
NOTE: You must program your keychain remote control (B) to the Smart Control receiver (A)
in order for the two to communicate.
NOTE: There are three buttons on your remote control (B). Each button can be used to control
one smart control receiver (A). Additional Smart Control receiver is sold separately.
1. Press and hold the "PROG"(1) button on the Smart Control Receiver (A) for 2 seconds.
The red LED (2) will start ashing continuously for 10 seconds.
2 Press the button (3) on the remote (B) you plan to use.
3. Once the remote (B) is programmed, the red LED on the Smart Control Receiver (A)
will ash slowly.
B
A
2
1
3
Section 10 - Replacing the Battery
NOTE: Dispose of old battery promptly and properly.
When the operating range is reduced, or when the LED does not ash during operation,
it is time to replace the battery.
The remote is powered by a Lithium battery CR2032 (included). Follow the instructions
below to replace the battery of the remote.
1. Undo the two screws (1) on the back of the remote. The bottom case (2) will then come off.
2. Take out the old battery (3).
3. Place the new battery (3) in position - positive side up.
4. Close the cover (2) and re-insert the two screws (1).
(2)
(1)
(3)
B
Section 6 - Erasing the Remote from Smart Control Receiver
NOTE: To erase the unwanted remotes from the Smart Control Receiver, rst erase all the
programmed remotes, then learn the ones you would like to keep.
1.
Press and hold the "PROG" button (1) on the Smart Control Receiver (A) for
approximately 10 seconds.
2.
The LED (2) will ash rapidly after 10 seconds indicating that all the
programmed remotes have been erased. You may release the
"PROG" button (1).
A
2
1
Troubleshooting
Problem
Solution
The LED on the remote does
Check if the battery isolator is removed and if the
not turn on when the button
battery is properly installed.
is pressed.
- Check if the batteries are properly installed.
The LED on the Smart Control
- Add a 6VDC, 300mA adapter (sold separately) to
Receiver does not turn on.
operate the Smart Control Receiver continuously.
- Check if the correct button is pressed.
- Ensure that the remote has been programmed to
The LED on the remote ashes
the Smart Control Receiver.
but does not operate the
- Check if the password function is enabled.
garage door.
- Reset the remote, disable the password function
and refer to the programming section to program
the remote to the Smart Control Receiver.
Section 7 - Remote Control Password Feature
NOTE: This function allows you to enter a password before pressing the garage door button
you assigned, for additional security.
NOTE: The password can be 2-8 digits long and can be a combination of buttons 1,2, and 3.
NOTE: Leave a 1 second pause period between entering the password and operating the
garage door. The factory default password is 2,2,2. The password setting on the remote control
(B) comes disabled as per factory default.
1. To enable or disable the password, press buttons 1 and 3 simultaneously and hold for
at least 5 seconds until the LED ashes quickly, but not until the LED ashes slowly.
2. Input the password (factory default 2,2,2).
3. Press button 1 and 3 once simultanesously to con rm. If the password is correct, the
password protection will be enabled/disabled.
4. To control your garage door, press the password 2,2,2 and 1 (the assigned button for
your garage door.
NOTE: If you enable the password protection, you can only operate the remote control (B), after
you input the correct password.
Warranty
ONE YEAR WARRANTY
This product is guaranteed to be free of defects in materials and workmanship for
1 year from the date of purchase. If this product is defective, call 1-800-304-1187 for
repair or replacement parts. Guarantee does not include normal wear and tear or
batteries.
If you have any questions, problems or missing parts,
please call Skylink Customer Support:
9:00am - 5:00pm EST, Monday-Friday.
1-800-304-1187
Or e-mail us at support@skylinkhome.com
www.skylinkhome.com
CUSTOMER SERVICE
17 Sheard Avenue,
Brampton, Ontario,
Canada L6Y1J3
P/N : 101Y169
Rev:1
©2014 SKYLINK GROUP.
Advertisement
