CONTENT SUMMARIZATION ............................1 SPECIFICATION .............................. 2 APPEARANCE ..............................4 INSTALLATION ............................... 6 Install display pole ..........................6 Hotkey sheet installation ........................7 Paper Installation ..........................8 4.3.1 Label Paper Installation ......................8 4.3.2 Receipt Paper Installation ......................10 4.3.3 Linerless Paper Installation ......................
Page 4
STATEMENT Please refer to PC software management manual in attached CD about the PLU editing, hotkey downloading, label editing and parameter setting etc.
1 SUMMARIZATION Unique and powerful network 1. Apply Ethernet technology, greatly improve data transmission speed. 2. Unique network testing, quickly test network communication. Simple and easy to operate 1. You can use single key to sell PLU quickly. Clerk can operate this scale without training. 2.
3 APPEARANCE LS2R: Display Power switch Tray Printer Hotkey Function key Numerical key LS2C: Display Power switch Tray Printer Hotkey Function key Numerical key...
Page 9
LS2N: Tray Printer Power switch Function key Numerical key Hotkey Circumvolve the 4 feet to adjust the level of scale, and make the air bladder into the circle. The gradienter is under Circumvolve the 4 feet to the tray. adjust the level of scale.
4 INSTALLATION 4.1 Install display pole ,and Mount 2. Open the LCD cover 3 1. Take out the fix set the display pole. 3. Cover the LCD, then put on fix set 4. Put on fix set .Connect the line, and like the picture shows.
4.2 Hotkey sheet installation Note: Please refer to “PC software management/Hotkey” in attached CD. Cut the hotkey sheet down and insert the hotkey sheet into the keyboard. Please take below pictures for your references: Cut the hotkey sheet down. Push up the hotkey pad from bottom according to the arrow head.
4.3 Paper Installation 4.3.1 Label Paper Installation Notice: please take the conveying protection bolt down, when you load the paper for the first time. Conveying protection bolt (2) Take out the printer, and open the turnable (1) Open the side cover printing assembly (3) Rip off the first several labels.
Page 13
(6) Close the turnable printing assembly. (7) Close the side cover 1. Turn the bar out wards, open the turnable printing assembly in the direction shown as the arrowhead ○ 2. Please rip off the first several labels, load paper in the direction shown as the arrowhead ○ , roll the release paper in the rewinder axis as the direction of arrowhead ○...
Label Paper We have two types of label paper: no-gap paper and gap paper Gap paper(2mm) No-gap paper The label paper we produced is very suitable for label scale. It is a kind of environment protecting material has suitable thickness, high sensitivity and low price. We can produce any kind of specification label paper to match your request.
Page 15
3. Load the paper like the map shows (directly lead the thermal paper to the paper outlet). 4. Pay attention to adjust the paper-fixing-block until the paper roll is fixed. Paper-fixing-block 5. Close the turnable printing assembly.
6. Close the side cover. NOTE: If you use thermal paper instead of label, you should choose ‘RECEIPT’ in ‘System Set’. Please refer to chapter 9.2 ‘System set’. 4.3.3 Linerless Paper Installation Note: The linerless paper printing module is different from the receipt and label printing module. If customers bought was the receipt or label printing module, but now want to replace it to the linerless paper module, please contact the service department.
Page 17
3 Close the rotatable printing assembly 4 Close the side cover...
4.4 PRINTER REPLACEMENT If the printer is damaged, you can follow the steps below to replace a new one. Precaution: Before you do the following operations, please cut the power supply first. Do not disassemble, assemble or adjust the printer if it is operating satisfactorily. In particular, do not carelessly loosen the screws holding various parts in place.
Page 19
Use a screwdriver to push the latch to the left side. Lift up the printer...
Pull out the cable 2. Install a new one Install new printer by following the demount procedure in reverse order. 5 KEYBOARD LAYOUT Note: Press “FEED” key for 2 seconds; the scale will adjust the paper’s position automatically; you yourself can also press it to adjust the paper minitrimly.
7 SALES OPERATION 7.1 Calculate by Weight There are three kinds of operation. If PLU data is downloaded by background server PC or pre-edited in the scale, operation follows method 1 or method 2. Otherwise the operation follows method 3. Notes: 1.
Page 22
METHOD 2: General sales steps by inputting LFCODE. Trade example: Some onions weighing 2.000kg are sold. Their LFCODE is 10, unit price is 1.500$/kg. ARROW DISPLAY OPERATION STEP REMARK Unit Zero Auto Weight Total price Ignore this step if the 1.
7.2 Tare Operation It is only applicable to the commodity packed in package or container such as eggs, beans or fruit and so on. MOTHOD 1: Operation for commodity separated from container or package. Trade example: A package of apples is sold. The hotkey of apples is 05, the net weight is 2.000kg and unit price is 6.000$/kg.
Take away This step is to leave container and the apples the weight-deducting →T← 0.000kg 0.00 0.00 on the tray, then press state. The arrow of “→T←” key. “tare” disappears. METHOD 3: Operation for commodity that its tare weight is known and has been set in software but could not separated from container or package.
METHOD 2: general operation step Trade example: Ten pieces of cakes are sold and the LFCODE of the cake is 12. The unit is PCS/kg. ARROW DISPLAY OPERATION Unit REMARK Zero Auto Weight Total price 1. Input the number of the 0.000kg 0.10 0.10...
Total discount ARROW DISPLAY REMARK OPERATION Unit Zero Auto weight Total price 1. Press key SHIFT & The LCD returns Total to initial state after Total Discount. Input the SHIFT Discount 0.000kg 0.00 0.00 Total Discount key discount amount 1$, and ENTER then press key ENTER.
METHOD 2: Trade example: Some apples are sold. The unit price of the apple is 4.000$/kg, and LFCODE is 900001. After change the unit price, the unit price of the apple is 3.000$/kg. ARROW DISAPLY OPERATION Unit Zero Auto Weight Total price LLFCODE?
Page 28
METHOD 2: Trade Example 1: The unit price of the cheese is 4.000$/ kg, and LFCODE is 15. Change the unit price of the cheese as 3.000$/kg. When finish this dealing, it will recover to the original price 4.000$/kg. ARROW DISAPLY OPERATION REMARK...
Page 29
METHOD 3: Temporarily change the price of the PLU, which is needed to be weighted. Trade Example:The unit price of the cabbages is1$/kg, and it should be change price as 2$/kg in the evening to promote it. When finish this dealing, it will recover to its initial price 1$/kg. Suppose a cabbage is 3kg, and its hotkey is 13.
8 SOME SIMPLE OPERATION 8.1 Copy price label 1. Call PLU or input unit price in normal state and print a piece of label. 2. Press “Copy” key and input a number between 1 and 9, then the corresponding number pieces of label is printed.
8.5 Package by Fixed weight Fix weight package, this function is available by setting on PC software first. For example: pack fish by the fixed weight 0.255kg, and the corresponding hotkey is 38. Note: Before operate on the scale, please press key Price Lock first, and the indicator light for ‘price lock’ will be lighting.
3. Put the orange on pan, 2.000kg 0.00 0.00 press hotkey 07 4. Put the grape on pan, 3.000kg 0.00 0.00 press hotkey 08 5. Press hotkey 01 3.000kg 0.00 34.00 8.8 Traceability Function This function is used to modify the traceability information temporary. This function should be activated from the item ‘System Set’.
9 FUNCTION SET 9.1 PLU Set Notes: This operation can be locked by password that is set in background PC changed randomly. PLU Input 1.Press PLU key for 2 seconds. The display shows “PLU EDIT”, it means the system is in the state of editing PLU.
9.2 System Set Note: This operation can be locked by password set in background PC server and is changeable as will. 1. Press the System Set for two seconds and then use “←” “→” to select the item ‘SYSTEM SET’to enter the system setting state.
If you choose “YES”, the system will be in stat. mode, when you use the hotkey, the sale subtotal of this key will be printed on label. And if you choose “NO”, you can do hotkey operation as normal. 27. stat Warnning? : Whether to set the stat. Warnning. Use arrow key to select “YES” or “NO”. 28.
9.5 Lock Scale You can lock the scale by password, so that other people can’t do any operation on the scale. Lock scale as the following method: 1. Press SHIFT Password key until the word “PASSW” appears on the LCD display. 2.
10 COMMUNICATION SETUP Ethernet TO PC NETWARE WINDOWS NT UNIX POS SERVER PC MANAGER POS1 POS2 Note: If the HUB/SWITHCH can’t identify the Crossover Cable when you use HUB/SWITCH to connect the scale, please use A Straight through Cable to replace the Crossover one.
10.1 Handshaking Flowchart of Label Scale and Background Link32 gathers Sale account from the scale Link32 run starting Command (201) Is there PLU Background is there Link32 sends end Change in requires sale Background? uploading sale account i command (220) account (120) Background transfers one Link32...
Page 39
Record package format: One record package includes three aspects: 1. Package length 4Byte 2. Command 4Byte 3. Record uncertain length Example: Starting command: 00080201 Package length: 0008 Command: 0201 Record: no ACK command: 00220102100000010000 Package length: 022 Command: 0102 Source: 02100000010000 From command list we can see responding command includes three aspects: Command: 0210 which means responding to command 0210 LFCode: 000001...
10.2 Making procedure of connector (1) Select a connector wire (8 pin) by length of L. (2) Put A end of the connector wire at the edge of blade of pliers horizontally (note: point against the baffle to ensure 12mm peeling length), press the pliers and pull out the wire and the peeling length is about 12mm.
11 TROUBLESHOOTING The scale breaks down: 1. There is no sound and no display but backlight when power is on. Reason: Electric sparkle caused by power plugging in and pulling out destroys the ROM program in the main board. Treatment: Change main board, reset sequence number and download all records. 2.
Page 42
Demonstration for cleaning the thermal printer head: Clean the thermal printer head. ② Clean the thermal printer head. ① Open the thermal printer head [Note]:The alcohol cleaning pen is with the scale when it leave factory. Please take it out as the picture shows below.
Page 43
Questions about weighing: 1. The scale can’t weigh correctly. Reason: a. Rubber pad, which sustains the scale pan, touched the shell (upper cover). b. Humidity or component aging or area difference makes the scale weigh incorrectly. c. Sensor is damaged by over loading. Treatment: a.
12 APPENDIX 12.1 Appendix 1: Barcode Coding List Barcode type Department Commodity Total price Weight Checksum number 00~09: Ean13 code, the front two codes represent department code: DD (2) IIIIIIIIII (10) DD (2) IIIIII (6) PPPP (4) DD (2) IIIII (5) PPPPP (5) DD (2) IIII (4)
Page 45
36-38: 18code, the front one code represents department code, which is particular for the batch management of live commodity. D (1) LLLLLL (6) IIII (4) RR (2) QQ.QQQ (5) D (1) LLLLLL (6) IIII (4) RR (2) QQQQ.Q (5) D (1) LLLLLL (6) IIII (4) RR (2)
12.2 Appendix2: Main difference between LB scale and LP scale: Main difference between scale with pole and scale without pole: LB serial Scale (with pole) LP Serial scale (without pole) System set option: System set option: R/T/D/B/P/A/L/H/O/M/S/I/J/X/K/E/F/C/Y/G/Q/N/U/V/W/Z/,/./ R/T/D/B/P/A/L/H/O/M/S/I/J/X/K/E/F/C Two select key ← (hotkey 11), → (hotkey 10). Only one select key →...
Need help?
Do you have a question about the LS2RX and is the answer not in the manual?
Questions and answers