Summary of Contents for EXP Computer CD ReWriter CRW-726
Page 1
PC Card CD ReWritable Installation Manual CRW-726...
Page 2
RMA number. You are responsible for packaging, providing proof of the date of purchase and the shipping cost of the failed product to EXP Computer, Inc. You are responsible for mailing the warranty registration card. The warranty claims may not be honored if there is no corresponding TROUBLE SHOOTING registration card on file at EXP.
Page 3
INTRODUCTION PART NAMES AND FUNCTIONS The CD ReWriter is a portable CD-ROM drive, which consists of a low- 1. Parallel Port interface cable power CD rewritable drive, a small 26 pin universal connector, a cable for Standard 25 pin Parallel port connector and 26 pin small connector. Parallel port (printer port),.
Page 4
INSTALLATION SOFTWARE INSTALLATION FOR WINDOWS 95/98 The installation procedures have two sections for each type of interface. Check all the connection as states in the “Hardware Installation” section. 1. Parallel Port interface From the Desktop Click ‘My Computer’ icon, ‘Control Panel’ and then ‘Add New Hardware’...
Page 5
3. Open "SCSI controllers". Click "Have Disk...". VERIFY YOUR INSTALLATION From “desk top” click on “my computer” icon. There should be addition CD-ROM drive’s icon displayed. SOFTWARE INSTALLATION FOR WINDOWS NT 4.0 Due to user interface similarity of the Windows 95 and the Windows NT 4.0.
Page 6
INSTALLATION FOR PCMCIA INTERFACE (OPTIONAL) SOFTWARE INSTALLATION FOR WINDOWS 95/98 NOTE: The PC Card interface is sold separately as an option component The “New Hardware Found” dialog box* will appear when you insert the CD for the CD ReWriter. Please contact EXP, if you wish to purchase very first time.
Page 7
SOFTWARE INSTALLATION FOR WINDOWS NT 4.0 For user with a newer revision of Windows 95 od Windows 98, “Update Device Driver Wizard” box * will appear. Click on “Next” button, let PC CARD Interface Windows 95 search for driver. Make sure to insert the CD device driver Currently there is no Plug and Play support for PC Card (PCMCIA) on the diskette into your floppy drive.
Page 8
CD-Audio and data CD. WARNING If you are using the CD Rewriter or software supply by EXP Computer Inc. to reproduce copyright data, you must obtain permission from the copyright owner. Consult your legal adviser before you proceed. You may be violate the...
Page 9
TROUBLE SHOOTING Symptom: The EXP CD starts to become excessively slow or does not PARALLEL PORT INTERFACE work at all. Solution: The parallel port on your machine may be able to a number of Symptom: No additional drive icon in “My Computer”. The EXP CD driver different modes, standard, Bi-directional, EPP or ECP.
Page 10
PCMCIA INTERFACE If you see the screen below, it means the PCMCIA device driver is not using 32-Bit Card Support. Follow on screen instructions Symptom: No “New Hardware Found” dialog box display. by except all the default setting. At the end of the installation, you will be asked to restart the computer.
Page 11
In some computer, the I/O Range XXX, Interrupt Request 15 Symptom: No additional drive icon in “My Computer”. may be use by a built-in secondary IDE controller. Try changing The EXP CD driver installed without any incident. the interrupt to 9,10 or 11. You can also try different I/O addresses.
Page 12
REMOVING OR RE-INSTALLING THE DRIVER PCMCIA INTERFACE (OPTIONAL) PARALLEL PORT INTERFACE If you need to remove or reinstalling the driver, make sure the EXP CD-ROM disk card is inserted. Go to “My Computer” icon, “Control Panel”, “System”,“ Device Manager” • Go to “My Computer”...
Page 13
APPENDIX A FCC COMPLIANCE STATEMENTS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Need help?
Do you have a question about the CD ReWriter CRW-726 and is the answer not in the manual?
Questions and answers