SERVICE MANUAL 4 HW-D1270TVE/ME Chapter 1 General Information 1-1. General Guidelines When servicing,observe the original lead dress.If a short circuit is found, replace all parts which are overheated or damaged by the short circuit.After servicing ,see to it that all the protective devices such as insulation barriers ,insulation papers shields are properly installed .Confirm that the screws,parts and wiring...
SERVICE MANUAL 5 HW-D1270TVE/ME Chapter 2 Product Feature 2-1. Features Environmental friendly to protect your skin. DC driver to save more energy and water High speed is available for easily dying and washed items are always ready for further use.
SERVICE MANUAL 6 HW-D1270TVE/ME 2-2. Specification washing machines HW-D1270TVE/ME Last update Product identification Description of appliance Washing machine Type of appliance(FS = standing, BI = built-in Supplier own brand Haier Supplier bar code Haier Commercial Brand / Model Haier Commercial bar code...
Page 7
SERVICE MANUAL 7 HW-D1270TVE/ME Adjustable feet n° Safety systems Auto door lock Motor overheating protection No heating without water Auto water cool-down (before drain 90° C boiled water) Water protection Acqua Stop kit ...
SERVICE MANUAL 19 HW-D1270TVE/ME Chapter 9 Error Display and troubleshooting 9-1. Error Display Error message:Door is not properly shut 20s after program is started. Troubleshooting: Pushing the door to Check Whether Door is Shut the door properly properly shut or not Cut off the power and then turn on again.
Page 20
SERVICE MANUAL 20 HW-D1270TVE/ME Check if drain pump acts by touching Check if drain pump or pump position drain pipe is jammed, and open the filter and clean Cut off the power and choose spin program to start, then check the import...
Page 21
SERVICE MANUAL 21 HW-D1270TVE/ME Error message :The heater may be broken Troubleshooting: Heater element Cut off power ,check the resistance must be broken pins heater element please replace it multimenter is it between 30-35Ω ? Turn on power ,and set wash...
Page 22
SERVICE MANUAL 22 HW-D1270TVE/ME Turn on power, and set pre-wash mode, then start. Check the import voltage of Electromagnetic valve must be broken, please electromagnetic valve by multimeter replace it. , is it between AC 220-240V between the white wire and red wire that they are not...
Page 23
SERVICE MANUAL 23 HW-D1270TVE/ME Check the import voltage between M1 Replace PCB wind and M2 wind, is it between AC 220-240V? Error message. Motor overheat protection or is damaged. Troubleshooting: Cut off power and check if motor wires Reconnect well...
Page 24
SERVICE MANUAL 24 HW-D1270TVE/ME Pull out water switch inserts and turn on Replace water pressure power, then set wash mode. While water switch is entering at the position of 1/4 glass window, check the resistance between ① and ②, is it 0? Check the resistance between ①and ③, is it infinite?
SERVICE MANUAL 25 HW-D1270TVE/ME 9-2. Examination & Troubleshooting 9-2-1. Display nothing Troubleshooting: Repair power supply Measure the power supply ,is it exists 220V-240V AC voltage? Press the power switch Is power switch on? Make sure power supply cable assembly is connected well and then Press power switch and check the replace power switch.
SERVICE MANUAL 26 HW-D1270TVE/ME Reconnect the wire there open circuit between electromagnetic valve and computer board? Replace PCB Choose pre-wash program and start, then check if there is 220-240V at export pin of electromagnetic valve 9-2-3. No draining Troubleshooting: Adjust the height of drain pipe to...
SERVICE MANUAL 27 HW-D1270TVE/ME Replace it Is belt loose or worn? Are the screws of counterweight and Fasten them motor loose? Dismantle triangle Remove belt and turn belt pulley by hand, check the bearing .If it and then check if there is different noise is broken, replace it.
Page 28
SERVICE MANUAL 28 HW-D1270TVE/ME Sincere Forever Haier Group Haier Industrial Park, No.1, Haier Road 266101, Qingdao, China http://www.haier.com Haier Washing Machine...