1. Manuals
  2. Brands
  3. Avitech Manuals
  4. Multiplexer
  5. Titan 9000 series
  6. User manual

Avitech Titan 9000 series User Manual

Modular card based multiviewer
Hide thumbs Also See for Titan 9000 series:
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
Titan 9000
Multiviewing experience taken to the next level
Revision 1.0.0, (May, 2013)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Titan 9000 series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Avitech Titan 9000 series

Summary of Contents for Avitech Titan 9000 series

  • Page 1 User Manual Titan 9000 Multiviewing experience taken to the next level Revision 1.0.0, (May, 2013)

  • Page 2: About This Manual

    Except as expressly written by Avitech International Corporation, the furnishing of this document does not provide any license to patents, trademarks, copyrights or other intellectual property of Avitech International Corporation or any of its affiliates.

  • Page 3: Table Of Contents

    Contents About This Manual ........................ii Technical Support ........................ii Warranty ............................. v Limitation of Liability ........................ v Extended Warranty Options ..................... v Services and Repairs Outside the Warranty Period .............. v Regulatory Information ......................v Federal Communications Commission (FCC) Statement ............. v European Union CE Marking and Compliance Notices ............
  • Page 4 5.5 Start/Stop Alarm Sound and Special Layout ..............61 5.6 Setting Group Parameters ....................62 5.7 Briefing ..........................65 Appendix A Using the LCD Panel ................67 A.1 Welcome Screen ......................67 A.2 Navigating the Main Menu ....................68 A.3 Navigating the System Parameters Menu ..............72 Appendix B Setting Up Static IP ..................

  • Page 5: Warranty

    Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Avitech is not responsible for any radio or Limitation of Liability television interference caused by using other than recommended Avitech’s liability under this warranty shall not exceed the purchase...

  • Page 6: Getting Started

    1. Getting Started The Titan 9000 Series is a modular card based Multiviewer. Each card can receive up to four input signals and up to four cards can be installed in the 1RU chassis. Users can monitor four HDMI/DVI/VGA/ YPbPr sources via HD 1080p output.
  • Page 7 Ear with screw RS-485 Cascading Cable (optional – (already installed on Titan 9000 upon order when purchasing 2 or more Titan 9000) for assembly on to rack mount) Proprietary RJ-45 to RS-232 (DB9-FM) Cable ® DVI to HDMI Adapter (optional) (optional) –...

  • Page 8: Product Features

     Supports DVI, features 4 DVI outputs (via a HDMI to DVI adapter)  Supports cascading, features an HDMI input for cascading  Supports Avitech’s Phoenix-Q configuration interface via Ethernet connection  Supports TSL through serial interface (RS-232) or Ethernet (IP) ...

  • Page 9: Specifications

    7. External Linear Time Code (LTC) 8. Safe area, aspect ratio detection 9. Screen background color is configurable  Audio Output Control: 1. Supports 8 channel embedded audio 2. HDMI: 8 channels selectable between the 4 groups 3. Analog: 1/8 inch stereo headphone jack for audio monitoring 4.
  • Page 10  1680x1050, 50Hz/60Hz  1920x1080, 50Hz/60Hz  1920x1200, 50Hz/60Hz Transmission of audio signal is not included when using the DVI to VGA, DVI to YPbPr adapters. Output Normal/VESA output timing; 8-bit/10-bit HDMI color depth; user configurable:  1920x1200 (WUXGA) 50Hz/60Hz ...
  • Page 11  1920x1080, 50Hz/60Hz  1920x1200, 50Hz/60Hz Output Normal/VESA output timing; 8-bit/10-bit HDMI color depth; user configurable:  1920x1200 (WUXGA) 50Hz/60Hz  1920x1080 (HD 1080) 50Hz/60Hz  1680x1050 (WSXGA+) 50Hz/60Hz/75Hz  1600x1200 (UXGA) 50Hz/60Hz/75Hz  1600x900 (HD+) 60Hz HDMI and DVI ...

  • Page 12: Connections To The Titan 9000

    1. One Titan 9000 – (HOB card) can do 1x2 wall display. Likewise, two Titan 9000 – (HOB cards) can do 2x2 wall display. 2. It is highly recommended to input at 1920x1080 and output at 1920x1080 resolution. Titan 9000 – (Control card) Control interface RJ-45 connector for connection to TSL port of the TSL controller for TSL (Ethernet/serial...
  • Page 13 Front Panel Go to previous selection Go to next selection A quick press moves the cursor one character to the left, while a long press deletes the character to the left of the current cursor Control Buttons position (e.g., set password) Moves the cursor one character to the right.
  • Page 14  For setup via the Avitech Phoenix-Q utility through network connection Ethernet (IP)  For entering the Avitech ASCII Protocol (AAP) X command interface  For connecting to TSL port of the TSL controller for TSL interface Headset 1/8 inch audio port for connecting headphones (stereo) Updates the firmware;...
  • Page 15 Rear Panel (control card) Rotary dial to assign unique addresses in systems with two or more chassis HDMI connector for multimedia input Cascade In (cascade from other Titan 9000 or from other video source as background image) Table 1-10 Titan 9000 – (Control Card) Component Description Figure 1-5 Titan 9000 Chassis Component Rear Panel (chassis)

  • Page 16: Hardware Configuration

    2. Hardware Configuration This chapter discusses the process of installing a card into Titan 9000 chassis. To prevent any damage to hardware components as well as avoid any injury, make sure to turn off power to the Titan 9000 by disconnecting the power cord before making any changes to the hardware configuration. 2.1 Installing the Card The Titan 9000 chassis accept any of the following cards: ...
  • Page 17 Step 3. Align both sides of the card to the rails, and slide all the way into the chassis. Figure 2-3 Align the Card to the Rail on Both Sides Step 4. Secure the screws on both sides to fix the card to the chassis. Figure 2-4 Secure the Screws on Both Sides...

  • Page 18: Phoenix-Q Configuration

    3. Phoenix-Q Configuration The Avitech Phoenix-Q program requires no installation. Just copy the system files to your computer’s hard drive. This chapter introduces the Phoenix-Q software for setting up the Titan 9000. 1. Make sure the Titan 9000 is powered on and connected properly to your computer through Ethernet before launching the Phoenix-Q software.

  • Page 19: Starting Up The Phoenix-Q Software

    Step 3. The following window will appear to signify a successful communication. Click OK to exit. Figure 3-2 IP Address Pinged Successfully 3.3 Starting Up the Phoenix-Q Software Step 1. Run the Phoenix-Q software by double-clicking Phoenix-Q.exe. Step 2. Make sure you have set the correct IP address (see Appendix A for details). Step 3.
  • Page 20 The computer will start to search for your Titan 9000. Figure 3-4 Phoenix-Q Software: Connection Progress When cascading the Titan 9000 make sure each chassis has a different rotary ID setting selected (e.g., 1 – 2 – 3) on their rear chassis. The Group View window will list the card(s) found and will initially be listed under Idle Group.
  • Page 21  Step 4. Click System Configuration. Figure 3-6 Phoenix-Q Software: Click “System””Configuration” The Group Setup window will appear. Figure 3-6 Phoenix-Q Software: Group Setup...
  • Page 22 Step 5. To assign the grouping drag the Idle Device on the left panel to the desired Group # on the right panel (e.g., Group 001). Figure 3-7 Phoenix-Q Software: Assign Group # to Idle Device Or, click the One Device Per Group button to assign a card to each group or click All Devices in Group 1 to assign all cards to belong to Group 1.
  • Page 23 After dragging/assigning the card, it is displayed as belonging to the assigned group. Figure 3-8 Phoenix-Q Software: Idle Device Assigned to Group 001 Step 6. Repeat the previous step for any additional Idle Device(s), if any. Next, click OK to exit the Group Setup window.

  • Page 24: Obtaining The Umd (Under Monitor Display) Data From Router

    The next figure shows sample idle devices assigned to groups. The “[1.1]” appearing before the card name signifies the chassis ID and card ID number. Hence “[1.2]” would signify chassis ID 1 and card ID 2. Figure 3-10 Phoenix-Q Software: Chassis and Card ID 3.4 Obtaining the UMD (Under Monitor Display) Data from Router ...
  • Page 25 The progress of disconnection will appear on screen. Figure 3-13 Phoenix-Q Software: Disconnection Progress  Step 2. Click System Options. Figure 3-14 Phoenix-Q Software: Click “System””Options”...
  • Page 26 Step 3. On the Options screen click External Device and make sure that Device Enable is set On. Figure 3-14 Phoenix-Q Software: Enable External Device Step 4. Make sure that the IP Address corresponds to the IP address of the computer running the …...

  • Page 27: Window Layout

    Step 5. Lastly, make sure that the Port Number shown is correct. If not, enter the value directly or click the up/down arrow button. Then click OK to exit the Option screen setup. Figure 3-16 Phoenix-Q Software: Enter Correct Port Number Make sure the value appearing for both IP Address and Port Number are similar to the value entered in the tpcGW utility, they must be to be able to successfully connect to the router.

  • Page 28: Resizing Window

    3.5.2 Resizing Window Perform the following steps to resize a window: Method 1. Right-click the mouse on a window, and then select Size. Followed by the desired preset size. Figure 3-18 Phoenix-Q Software: Select a Preset Size Method 2. Resize a window by dragging the border of a window to the desired size. Keep in mind that there is a scaling limitation for each window that limits the minimum scalable size to 128×80 pixels for NTSC/PAL video (320×180 for Titan 9000-HOB).
  • Page 29 3.5.4 Visual Studio For a quick global view of monitors installed in the studio, click the Visual Studio tab to easily glance the present set ups. Figure 3-20 Phoenix-Q Software: Group Layout Quick Information Positioning the cursor on top of a window will provide a quick information of the window. As ...
  • Page 30 Layout For a quick layout setup of your video windows, right-click the mouse anywhere on a window to access the Layout menu. Select from 2×2 up to 10×10 as possible grid positions, as well as specify a fixed 1 row by “N” columns or “N” rows by 1 column. Figure 3-22 Visual Studio: Modify the Layout...

  • Page 31: Basic Setup Using The Phoenix-Q Software

    4. Basic Setup Using the Phoenix-Q Software This chapter introduces you to the Phoenix-Q software for setting the features of your Titan 9000; as well as familiarizes you with the menus appearing on the Phoenix-Q software. Some items appearing on the menus of the Phoenix-Q software may not be available (grayed-out). 4.1 File Menu Figure 4-1 Phoenix-Q Software: File Menu All the presets you create are stored in the Titan 9000 flash memory, not on your computer.
  • Page 32 The file extension GP# will be automatically added to the filename. 1. When using a keypad, use the numbers 0–9 for your preset names. 2. When using the GPI, use the numbers 1–8 for your preset names. Each group’s preset can be saved by clicking Save Global Preset (with checkmark); and the file extension GLB will be automatically added to the filename.

  • Page 33: Edit Menu

    Step 5. Select a saved file and then click OK to load the preset. Figure 4-5 Phoenix-Q Software: Load Preset File Just like the Save window you can delete a file appearing on the Load window by right-clicking the filename and clicking Delete.

  • Page 34: View Menu

    Font Type: Click Font Type to select the Font, Font style, and Size. Then, click OK. Figure 4-7 Phoenix-Q Software: Set Font Properties For Windows 7: When using the Phoenix-Q in a different language other than English the Font “Arial” might not appear as the default font-type.
  • Page 35 Toolbars and Docking Windows: Enable (with checkmark) or disable the display of the Standard toolbar, Available Windows panel, Log Window panel, Group View panel, Properties panel, Briefing panel, as well as Customize the display. Figure 4-9 Phoenix-Q Software: “Toolbars and Docking Windows” Menu Customize: Click Customize to design the look of the menus and commands appearing on the Phoenix-Q software.
  • Page 36 Application Look: Click Application Look to select the overall design and theme of the Phoenix-Q software. Click on the themes title to view the theme. Note: The “dot” in front of Visual Studio.NET 2005 signifies that it is the currently selected theme. Figure 4-11 Phoenix-Q Software: “Application Look”...

  • Page 37: System Menu

    4.4 System Menu Figure 4-12 Phoenix-Q Software: System Menu System Menu Connect the computer and Titan 9000 via Ethernet connection; or Connect or Disconnect it. Before connecting make sure that the correct Disconnect configurations are entered under the item Communication. When you have unplugged the Ethernet cable and re-connected it, click Reconnect Reconnect to continue the configuration process.
  • Page 38 Restore: To manually Restore a preset perform the following steps. Step 1. Set the Titan 9000 to the factory-default value (see Appendix B for details). Step 2. Make sure that the rotary ID setting of the chassis being restored matches the old chassis’ setting (if the restoration to be attempted is not for the same chassis).
  • Page 39 When the setup of the Present Configuration window is different from the setup in the Preview Configuration window (e.g., upon selecting Backup_2013_03_05_14_15_10 folder in the Date window) then restore is not allowed by the system and the Restore button remains grayed-out. Step 6.
  • Page 40 Use the Setup Speaker ID function to set up the speaker to monitor the audio source by assigning the Speaker ID number (1 to 32) for each card ID. Click to assign One group per speaker or to assign All group in one speaker.
  • Page 41  Step 1. Click System Export Label (.txt) and assign a filename. Then click Save. Figure 4-20 Phoenix-Q Software: Export Label Step 2. Open the exported text file. The first row of text provides a guide to the two types of labels (A for ANSI / B for BMP Label).
  • Page 42  General Backup Path The default backup path “C:\Avitech\Backup\” contains the system configuration, preset files, system log data, and firmware version information. To change the backup path, type the desired path in the Value column (if available). Figure 4-24 Options: “System””General””Backup Path”...
  • Page 43 … Or click the select folder button “ ” (if available) and when the Select Folder screen appears select from the existing folders or click the Make New Folder button to create a new folder. Then click OK to exit. Figure 4-24 Phoenix-Q Software: Select Folder Window ...
  • Page 44   General New Device Detected Click the drop-down button (use the mouse to click the cell’s rightmost portion) to select Open Group Setup window that allows the Phoenix-Q program to automatically open the Group Setup window when a new device has been detected. Figure 4-26 Options: “System””General””New Device Detected”...
  • Page 45   General Display Device ID (Group View) To display the device ID information in the Group View panel, make sure Display Device ID (Group View) is enabled (set On). Click the drop-down button [use the mouse to click the Display Device ID (Group View) cell’s rightmost portion] to select On.
  • Page 46    General Display Name Custom Name Type the group’s new name (up to 30 characters). Figure 4-30 Options: “System””General””Custom Name”   Play Alarm Sound No Video Make sure that Play Alarm Sound when No Video occurs is Enabled (set On). Click the select …...
  • Page 47   Play Alarm Sound No Audio Make sure that Play Alarm Sound when No Audio occurs is Enabled (set On). Click the select … folder button “ ” and when the Alarm Sound screen appears click the select folder button choose another alarm sound to play when no audio occurs.
  • Page 48 Display Type: Quad/Full screen Sample scenario 1 – a single window loses video signal Regardless of the present monitor’s window layout, the quad/full screen layout would be displayed and the single window without video signal would occupy the top-left position/full screen to warn user that the particular window has no video signal.
  • Page 49   External Device Device Enable To allow the Phoenix-Q software to get the UMD (under monitor display) data from the router (when necessary) click External Device and make sure that Device Enable is set On. Figure 4-35 Options: “External Device””Communication””Device Enable” ...

  • Page 50: Help Menu

      External Device Port Number Make sure that the Port Number shown is correct. If not, enter the value directly or click the up/ down arrow button. Then click OK to exit the Options screen setup. Figure 4-37 Options: “External Device””Communication””Port Number” Make sure the value appearing for both IP Address and Port Number must be similar to the value entered in the tpcGW utility to be able to successfully connect to the router.
  • Page 51 Firmware Version Step 1. Click Firmware Version. Figure 4-39 Phoenix-Q Software: Firmware Version Step 2. Click Export. Step 3. Assign a filename and click Save to store the data. Figure 4-40 Phoenix-Q Software: Save Firmware Version Information Upgrade Firmware: Click Upgrade Firmware to bring the device’s firmware up-to-date (see “Firmware Upgrade Reference Guide for Titan 9000”...

  • Page 52: Setting The Group/Card Properties

    5. Setting the Group/Card Properties To set the properties of the Titan 9000, click to select the Card on the Group View window (left panel) and the Properties window (right panel) would list the parameters available for setup. Figure 5-1 Phoenix-Q Software: Properties Window Some of the items appearing on the Properties window may or may not be available for your Titan 9000.
  • Page 53 Note: The RS-232 port is not for connecting to a computer for configuration (Phoenix-Q utility). Likewise, it cannot be used for entering any Avitech ASCII commands. When configuring, connect the (Master Titan 9000) to the controlling computer via an Ethernet connection and then connect the (Master Titan 9000) RS-232 port to the TSL router.
  • Page 54 (On / Off) Select the display address. The address should match the TSL controller’s configured address connected to the router output feeding the corresponding Avitech input. Display Address Upon right-clicking Display Address and clicking Quick Setting, set the (0 up to 126) starting and ending number (0-126) to be displayed for each four sources (e.g., Set 100 as the Start Number for Source 1 and set 126 as the End...
  • Page 55 TSL UMD (Source 1/2/3/4) Properties Option Select to display 8 or 16 dynamic characters (if the TSL implementation First 8 Characters allows it). All 16 Characters Tally Enable Enable tally for a window or all the windows in a group. (On / Off) Flash Enable flashing tally for a window or all the windows in a group.
  • Page 56 Embedded Audio Select the source of embedded audio signal that will be outputted through HDMI OUT port; whether Local (from the card’s HDMI IN port) or Pass HDMI Out Type through embedded audio (from cascaded signal source) Select the source of embedded audio signal; from each window’s HDMI Source IN port.
  • Page 57 Clock Set the background color appearing on the clock. Click Others for more color choices (Standard tab) or customize the color (Custom tab) by setting the Hue/Saturation/Luminance as well as the Red/Green/Blue values. Clock B-G Set the background transparency level of the clock. 0 signifies total Transparency transparency.
  • Page 58 Clock Specify the desired time zone shown on a particular monitor. Time Zone Note: This item is not available when you select Counter in Source. Broadcast Sync Allows the card to synchronize the clock with an external SNTP time Time server.
  • Page 59 Clock Label Background Color Specify the clock label’s background color. Click Others for more color choices (Standard tab) or customize the color (Custom tab) by setting the Hue/Saturation/Luminance as well as the Red/Green/Blue values. The following table shows the Properties setting for each window in the Titan 9000. Window Show or hide the selected window on the monitor.
  • Page 60 Window Font Color Specify the window label’s font color. Click Others for more color choices (Standard tab) or customize the color (Custom tab) by setting the Hue/ Saturation/Luminance as well as the Red/Green/Blue values. Background Color Specify the window label’s background color. Click Others for more color choices (Standard tab) or customize the color (Custom tab) by setting the Hue/Saturation/Luminance as well as the Red/Green/Blue values.
  • Page 61 Window Meter Group 1 Meter Group 2 Select the audio meter’s group (embedded audio). Meter Group 3 Meter Group 4 Select the audio meter’s width. Width (2 / 4 / 6 / 8 / 10 / 12 / 14) Select the meter’s ballistics. Meters which monitor audio levels are typically one of two varieties: VU (Volume Unit) or PPM (Peak Program Meters).

  • Page 62: Copy Window Properties

    Image Adjustment Brightness Adjust the brightness quality of the input signal. (–128 to 127) Contrast Adjust the contrast quality of the input signal. (0 to 1023) Alarm Enable Activate the various alarm features. (On / Off) Video Alarm Enable Activate the video signal alarm feature. (On / Off) Border Red Color...
  • Page 63 The properties of a window can be copied to another window on the same card, as well as between cascaded chassis. Step 1. Right-click a window and select Copy. Figure 5-3 Phoenix-Q Software: Right-click Window and Click “Copy” The properties that can be copied include the following: ...

  • Page 64: Undo/Redo Changes

    5.2 Undo/Redo Changes Clicking the allow you to undo the previous step; while clicking the allow you to redo the previous step that was undone. To undo or redo multiple actions click the drop-down arrow symbol beside the undo/redo button, then highlight and click the actions to be undone or redone. Click the scrollbar to highlight more than 6 actions.

  • Page 65: Copy Window Size

    5.4 Copy Window Size This function allows a set of windows to copy the width, height, and size of a window appearing on screen. For example, clicking the Make Same Width button ( ) would cause the selected windows to have the same width. To modify the window size: Step 1.

  • Page 66: Start/Stop Alarm Sound And Special Layout

    5.5 Start/Stop Alarm Sound and Special Layout Before starting or stopping playing of alarm sound when no video or no audio occurs; as well as display of special screen layout when no video occurs, make sure to enable the feature. To find out click SystemOptions on the Phoenix-Q software’s drop-down menu.

  • Page 67: Setting Group Parameters

    5.6 Setting Group Parameters The settings here only affect the cards included in a particular group. Upon right-clicking a particular Group # (e.g., Group 001) heading portion the following menu will appear. Figure 5-11 Phoenix-Q Software: Set Group Parameter  Click Group Reset to refresh all cards belonging to the same group.
  • Page 68  Click Set Subgroup. Figure 5-12 Phoenix-Q Software: “Cascade In Switch & Device Cascade Series” Window...
  • Page 69 Click the checkbox to enable or disable “cascade in” for each ID number. Use the mouse to change the ID number designation only (by dragging using the symbol); this will not affect the actual physical connection of the Titan 9000. Figure 5-13 Phoenix-Q Software: Drag to Change the ID Number Designation Only Make sure the ID number designation must match the actual physical connection of the cascaded Titan 9000.

  • Page 70: Briefing

    5.7 Briefing This function allows you to cycle between presets for a slideshow effect. Step 1. Right-click the title bar and when the menu appears, click Add. Figure 5-14 Briefing: Click “Add” Step 2. Enter the Process name, specify the Time (H : M : S), then select the previously saved preset File.
  • Page 71 Step 2. Assign a filename and click Save to store the data. Figure 5-18 Phoenix-Q Software: Save Log Window Information You can also refer to your computer’s hard drive (C:/Avitech/Backup/Backup_date_time/Log/ folder) for various system log messages text file. Figure 5-19 Phoenix-Q Software: Location of Auto-save Log File...

  • Page 72: Appendix A Using The Lcd Panel

    Appendix A Using the LCD Panel This chapter discusses the process of using the LCD panel to set up Titan 9000. The LCD panel allows for control of the Titan 9000 including; output resolution and signal adjustment, user logo, audio (headphone and HDMI), cascade, HDMI output source, preset file, color correction, clock, window display parameters, alarm, aspect ratio adjustment, safe area and operational status report.

  • Page 73: Navigating The Main Menu

    A.2 Navigating the Main Menu 1. Press the button from the default initial screen to enter the main menu. 2. Use the buttons on the front panel to navigate: ( 3. The following sections are setup items on the main menu, details of each are in the following tables, respectively: Resolution Select the desired display resolution and frequency.
  • Page 74 Audio On: listen to the audio output via headphones.  Mute: disable the audio output via headphone feature.  On/Off  Sound: select the left/right/both channels.  Stereo  Mono L (left)  Mono R (right)  Volume: adjust the volume. ...
  • Page 75 Auto Layout Press the button to rearrange the windows layout appearing on the monitor.  2×2 layout if only 1 card in the chassis  3×3 layout if only 2 cards in the chassis  4×4 layout if only 3 cards in the chassis ...
  • Page 76 Full Screen On: allow the selected window to appear in full screen mode (default setting is OFF). Status Off: window appears in its present configuration. Exit Exit the window full screen menu. Table A-13 Window Full Screen Signal Format On: display the window’s input signal format. Status Off: disable the display of the window’s input signal format.

  • Page 77: Navigating The System Parameters Menu

    Window Border On: display the border for the particular window. Status Off: disable the border of the window. Exit Exit the window border setup menu. Table A-18 Window Border Image Border On: display the border for the particular image. Status Off: disable the border of the image.
  • Page 78 LCD Panel Adjust the LCD panel contrast. Contrast  0 to 26 Table A-24 LCD Panel Contrast Lock LCD Panel On: enable the lock LCD panel feature when a set idle time has elapsed.  Password: input the text string for unlocking the LCD panel (up to 7 characters).
  • Page 79 Dual Power On: turn on the power alarm feature that is triggered when either one of the power source in redundant power supply is cut-off. Status Off: disable the dual power alarm feature. Exit Exit the dual power alarm setup menu. Table A-28 Dual Power Alarm...

  • Page 80: Appendix B Setting Up Static Ip

    Appendix B Setting Up Static IP The following two methods allow Titan 9000 to be in the same network mask with the connected computer. Method 1: Change the IP Address of the Titan 9000 Master Chassis Step 1. Run the Phoenix-Q software by double-clicking Phoenix-Q.exe. Figure B-1 Phoenix-Q Software: Initial Screen...
  • Page 81 Step 2. Change the IP address by first clicking the default IP Address: 192.168.0.5 entry in the IP Connection List window. Then, click Change Connection Properties. Figure B-2 Phoenix-Q Software: Click “Change Connection Properties” The present IP address is shown in the IP address field. The corresponding Subnet Mask and Gateway belonging to the present IP address is also displayed.

  • Page 82: Method 2: Change The Ip Address Of The Controlling Computer

    Step 4. Click OK to exit. Figure B-4 IP Address Change Successful Method 2: Change the IP Address of the Controlling Computer For Windows XP Step 1. Click Start, and then right-click the mouse on My Network Places, and click Properties. Step 2.

  • Page 83: Appendix C Resetting To The Factory-Default State

    Appendix C Resetting to the Factory-Default State Step 1. Power-off the Titan 9000 by unplugging the power cord. Step 2. Push the number 2 dip switch located on the control card downward to the ON position. Figure C-1 Push Number 2 Dip Switch Downward Step 3.

Table of Contents