Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zitzi Guppy
Summary of Contents for Zitzi Guppy
-
Page 1: User Manual
User manual... - Page 2 Check the checkbox if the product is CUSTOMIZED. The CE Mark is no longer valid and should be removed. The product is only intended for use as an under frame together with seating systems produced by Anatomic SITT AB. If other uses are desired, please contact Anatomic SITT AB.
-
Page 3: Safety Precautions
Safety precautions Introduction For you to use all advandtages of the Zitzi Guppy, it is important that you read through this manual thoroughly. This applies to all persons who are in the vicinity of the user. Adjustment of the Zitzi Guppy should always be performed by medically qualified person. -
Page 4: Table Of Contents
Using the transportation kit Caster positioning Caster fork position Direction lock Angle adjustment of caster fork Install the direction lock Activate direction lock Brake Releasing the direction lock Drum brake © Anatomic SITT AB User manual - Zitzi Guppy I 4... - Page 5 Recommendations Gas piston Risk assessment Warranty Terms of sale Combinations Warranty Spare parts Warranty claims Marking Returning products Recycling Reconditioning Customer service Service Technical data Cleaning Finishing Marking Wheels © Anatomic SITT AB User manual - Zitzi Guppy I 5...
-
Page 6: Seat Part
Tighten the screws (D) firmly. Note! The picture shows only one type of mounting plate assembly instructions. For more information about mounting plates, see the instruction manuals for se- lected seating system. © Anatomic SITT AB User manual - Zitzi Guppy I 6... -
Page 7: Tilt
To restore the angle to its neutral position, press the tilt handle (A) and push the handle upwards and backwards. Obs! Be careful to avoid risk of pinching while tilting the seat. Obs! Be aware of the possible increased risk of overturn during tilt. © Anatomic SITT AB User manual - Zitzi Guppy I 7... - Page 8 © Anatomic SITT AB User manual - Zitzi Guppy I 8...
-
Page 9: Armrest
Loosen the screws (A) and adjust the angle using the three holes (E) in the attachment. Depth adjustment Loosen the screws (D) underneath the armrest plate and adjust to required position using holes underneath. © Anatomic SITT AB User manual - Zitzi Guppy I 9... - Page 10 © Anatomic SITT AB User manual - Zitzi Guppy I 10...
-
Page 11: Driving-Handle
Angle adjustment of driving-handle Press the buttons (D) on the inside of the driving-handle and adjust. Fold the push-frame Release the adjusters (C) and fold the push-frame forewards. Tighten the adjusters (C). © Anatomic SITT AB User manual - Zitzi Guppy I 11... -
Page 12: Wheels With Quick-Release
Secure that the wheel is installated properly by trying to pull it outwards. Release the wheel Press and hold the button (B) in the wheel center as you pull off the wheel from the chassis. © Anatomic SITT AB User manual - Zitzi Guppy I 12... -
Page 13: Driving Wheels
For advice and help balancing the wheelchair, please contact your dealer. Notice! NOTE that changing the wheelposition might increase the risk of tipping. Notice! The screws should not be taken out completey. Just loosen them a little. © Anatomic SITT AB User manual - Zitzi Guppy I 13... -
Page 14: Caster
You kan adjust the castors in five different height positions. This allows you to adjust the castor height after positioning the driving wheels. Obs! OBS! Secure that the screws is properly tighten after the adjustment. © Anatomic SITT AB User manual - Zitzi Guppy I 14... -
Page 15: Caster Fork Position
Loosen and rotate the eccentric nuts (C) on the caster attachment (B) until the correct angle is obtained. Tighten the screws properly after adjusting the caster fork. Obs! Make sure the screws are properly tightened after the adjustment. 90° Ground © Anatomic SITT AB User manual - Zitzi Guppy I 15... - Page 16 Detailed drum brake © Anatomic SITT AB User manual - Zitzi Guppy I 16...
-
Page 17: Brake
Squeeze the brake by lifting the drum brake arm (E) and move the nut (D) further up the wire. Tighten the nut (D) and adjust the tension with the screw (C) © Anatomic SITT AB User manual - Zitzi Guppy I 17... - Page 18 © Anatomic SITT AB User manual - Zitzi Guppy I 18...
-
Page 19: Installation Of Drum Brake
When selecting the 16 ” wheels, the screw (C) is threaded directly in the plate. Note! For more information on how to use the quick-release, see page 12. Note! The installation of the drum brake is the same for all wheel sizes. © Anatomic SITT AB User manual - Zitzi Guppy I 19... -
Page 20: Parking Brake
Tighten the screws (E) when required position is reached. Using the handbrake Set the handbrake (D) by pressing the handbrake arm forward. Pull the arm back to release the handbrake. © Anatomic SITT AB User manual - Zitzi Guppy I 20... -
Page 21: Footrest
When the footrest attachment is installed to the chassis you can adjust the heght of the footrest. Loosen the adjuster (F) and adjust to required height. Tighten the adjuster. © Anatomic SITT AB User manual - Zitzi Guppy I 21... -
Page 22: Calf Support
Loosen the screws (A) slightly and then adjust to the required height. Tighten the screws (A) Widht adjustment of the calf support Loosen the screws (B) slightly and then adjust to the required widht. Tighten the screws (B) © Anatomic SITT AB User manual - Zitzi Guppy I 22... -
Page 23: Anti-Tip Device
Finish by placing nut covers (D) as illustrated. Note! Zitzi Guppy should always be equipped with anti-tip device because of its many adjustment possibilities. Using the anti-tip device The anti-tip should be used for a safer and secure usage of the chassis. It can easily be folded when not in use by carefully stepping down the anti-tip and turn it aside. -
Page 24: Step Bar
Push the step bar with your foot while holding the driving handle and gently pull the chassis backwards to free up some space under the castors. Obs! It is important to hold the driving handle firlmy while using the step bar. © Anatomic SITT AB User manual - Zitzi Guppy I 24... -
Page 25: Installation Of Front Bracket
Craschtested and approved Craschtested and approved according to 7176-19 for 70 kg. Note! When using the transportation kit, the angle of the chassis has to be 0°. © Anatomic SITT AB User manual - Zitzi Guppy I 25... -
Page 26: Transportation Kit
Transportation kit © Anatomic SITT AB User manual - Zitzi Guppy I 26... - Page 27 Pull the locking pin (H) straight up and then rotate 90° and release the pin into the hole in the movining part. Ensure that the direction is locked. Note! Direction lock fits only by choosing the 7” castors. © Anatomic SITT AB User manual - Zitzi Guppy I 27...
-
Page 28: Direction Lock
Direction lock © Anatomic SITT AB User manual - Zitzi Guppy I 28... -
Page 29: Mudguards
You can adjust the mudguars in height by loosen the screws (D). Adjust to re- quired heigt and then tighten the screws (D). Tips! You just need to loosen the screws (D) slightly. © Anatomic SITT AB User manual - Zitzi Guppy I 29... - Page 30 Indication for transportation brackets Guppy from above with the drive wheels closest to the footer © Anatomic SITT AB User manual - Zitzi Guppy I 30...
-
Page 31: Transportation In A Vehicle
Crash tested and approved is crash tested and approved according to ISO 7176-19 up to 70 kg. Note! Crash test is approval valid for weights up to 70 kg. © Anatomic SITT AB User manual - Zitzi Guppy I 31... -
Page 32: Maintenance Instructions
Further, they should be stored so that the piston rod is placed facing downward. Otherwise, the gas spring seal might break and the gas piston fail. Note! Gas piston must be activated regularly © Anatomic SITT AB User manual - Zitzi Guppy I 32... -
Page 33: Warranty
Zitzi Delfi Pro and Anatomic Sits. For other combinations please contact Anatomic SITT AB. Spare parts For the CE marking of the Zitzi Guppy to be valid, the frame may only be fitted with spare parts delivered by Anatomic SITT AB. Marking Zitzi Guppy and its accessories are CE marked products. -
Page 34: Reconditioning
Reconditioning Service Regular maintenance is important for the Guppy to funcion safe and properly. The need for service changes is dependending on use and wear. Check all moving parts and fasteners regularly. Useoriginal parts from Anatomic SITT AB when reconditioning the Guppy. -
Page 35: Stability
Function control means that you go through wheels, stability, brakes, push handle and push bar. Notice! Always check that the device is not customized when reconditioning, before it is sent to new users. © Anatomic SITT AB User manual - Zitzi Guppy I 35... -
Page 36: Adaptation And Customization
Adaptation and customization Guidelines and recommendations Every time the Zitzi Guppy is altered in some way, an assessment has to be made to determine if it is an adaptation or a customization. An adaptation is any change made in comprehension of the CE mark. All other changes are customizations. -
Page 37: Terms Of Sale
40% of the invoice value For products returned more than 360 days from delivery no refund is made for the products Customized products cannot be returned © Anatomic SITT AB User manual - Zitzi Guppy I 37... -
Page 38: Customer Service
Tel. +353 021 461 8000, Fax +353 021 461 8099 Tel. +603 8070 9166, Fax +603 8073 9166 Email info@gymncare.com Mobilitec Rua dos Verdes 123, PRT-4470-658 Pedras Tel. +351 229 436 130, Fax +351 229 436 139 © Anatomic SITT AB User manual - Zitzi Guppy I 38... -
Page 39: Technical Data
41 cm 57 cm 48,5cm 44,5 cm The total lenght of the chassi change depending on location and wheels. C measurement is taken at the height of castor house. © Anatomic SITT AB User manual - Zitzi Guppy I 39... - Page 40 Fax +45 86 17 01 75 Anatomic SITT Nederland B.V. Postbus 6027 / 4000 HA Tiel, The Netherlands Tel +31 344 63 45 40 Fax +31 344 62 33 61 anatomicsitt.com info@anatomicsitt.com facebook.com/anatomicsitt youtube.com/anatomicsitt © Anatomic SITT AB User manual - Zitzi Guppy I 40...