Showview Programming - LG LH-CX245 Owner's Manual

ShowView
Programming
ShowView greatly simplifies entering the date,
channel, start and end times of a Timer
Recording by simply entering a ShowView Code.
ShowView Codes are published in most TV
guide magazines; they can vary one to nine
numbers in length.
S V is a registered trademark of Gemstar
HOW IEW
Development Corporation.
The S V system is manufactured under
HOW IEW
licence from Gemstar Development Corporation.
1. Make sure that TV channels have been tuned and
stored in correct SHOWVIEW order. Insert a video
cassette with protection tab into your DVD/VCR
Combi receiver.
SHOWVIEW NO.
- - - - - - - -
ONCE
REC
2. Press SHOWVIEW.
D E
3. Press or to select the recording type.
ONCE: To record once.
WEEKLY: To record at the same time every week.
DAILY: To record every day (except Saturday and
Sunday) at the same time.
4. Press the numbered buttons to enter the
ShowView Code of the TV programme that you
wish to record.
If you make a mistake press
revised number.
SHOWVIEW NO.
246876543
ONCE
REC
5. Press OK.
If PLEASE CHECK is displayed it means that you
have entered the wrong ShowView number,
entered the ShowView number incorrectly.
If "- -" is displayed, you have to enter the
programme number of the station, you want to
record from.
PR DATE TIME
PR-01 12 10 : 11 11 55
- - - - - - - - - - - - :
- - - -
- - - - - - - - :
- - - -
- - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
6. Press F or G to select the settings that you wish to
revise. (PR, DATE, TIME, VPS and SP).
Press D or E to enter the correct information.
-
0~9, OK i
F then enter the
0~9,
OK i
~ : SP
~ : SP
~ : SP
~ : SP
~ : SP
~ : SP
~ : SP
i
PR DATE TIME
PR-01 12 10 : 11 11
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - -
- - - - - - - - :
- - - -
- - - - - - - - :
- - - - - - - - - - - - :
7. Press D or E to switch VPS/PDC on or off.
Press G to select the recording speed.
Press D or E to select the desired tape speed (SP,
IP, or LP).
IP mode determines how much tape is left and
switches speed from SP to LP, if necessary, to
complete recording the program. IP mode is not
selected when VPS/PDC is ON. Check that the
timer event details are correct. If you wish to record
from AUDIO IN and VIDEO IN on the front or from
either of the EURO SCART sockets on the back of
DVD/VCR Combi receiver, press AV to select for
correct display (AV1, AV2 or AV3).
PR DATE TIME
PR-01 12
10 : 11 11 55
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - - - - - - - - - - :
- - - -
- - - - - - - - :
8. If you want to make another ShowView recording
repeat stages 2 - 7. Press i twice.
If PLEASE CHECK is displayed, you have entered
incorrect information and will need to re-enter the
data.
Press POWER to switch your DVD/VCR Combi
receiver power off mode.
recorder's display while your DVD/VCR Combi
receiver waits to make the recording.
To watch a DVD during timer recording standby
mode, press POWER and DVD to switch to DVD
mode.
9. Press STOP to end recording.
Notes
• Video Programme System (VPS)
The Video Programme System (VPS) ensures that
the TV programmes that you have programmed for
timer recording will be recorded exactly from their
beginning to end, even if the actual broadcasting
time differs from the scheduled time due to delayed
start, or if the programme is extended beyond its
scheduled time. Also, if a programme is interrupted,
for example, if a news flash is inserted, the record-
ing will also be interrupted automatically and
resumed when the programme continues.
The VPS signal is broadcast by the TV station and
this controls the timer in the video recorder.
VPS should be set ON for all timer recordings from
TV stations broadcasting these signals. It should be
set OFF for all timer recordings from TV stations that
are not broadcasting these signals.
SP
~ : 55
SP
~ :
~ : SP
~ : SP
SP
~ :
SP
~ :
SP
~ :
i
~ :
SP
~ :
SP
~ :
SP
~ :
SP
~ :
SP
~ :
SP
~ :
SP
i
will appear in the video
29