Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Netphonic NG-188
Summary of Contents for Netphonic NG-188
- Page 1 NG-188 User Manual NG-188 User Manual 1 / 46...
-
Page 2: Table Of Contents
NG-188 User Manual NG-188 Features....................4 Appearance .........................4 Interface ........................4 Electricity characteristic .....................4 Software........................5 Standard and Protocols .....................5 Compliant Standards....................6 Operating requirement....................6 Package ........................6 Installation........................7 Web Configuration ....................8 Access Web setting page..................8 Current state........................9 Network ........................10 Wan Config..................10 2.3.1 LAN Config ..................11 2.3.2... - Page 3 Network Diagnosis .....................41 Restore to factory default..................41 POST Mode(safe mode) ...................42 FAQ........................43 How many SIP servers may NG-188 register simultaneously?........43 How can I know the NG-188’s IP address?..............43 How to use NG-188’s Lifeline function?................43 Why the settings vanish after reboot?................43 How to use the dial rule?.....................43...
-
Page 4: Ng-188 Features
NG-188 User Manual 1 NG-188 Features Appearance Power: Power indicator. Server: Server indicator. Registered: ON; Registering: Blinking; Do not register: OFF. VoIP: Indicate the calling status. Hook-on: OFF; Hook-off and in VoIP state: ON; Hook-off and in PSTN state: OFF... -
Page 5: Software
NG-188 User Manual The network connects:2 RJ45 connect, a WAN, a LAN One Liftline Software Support two sip servers running at the same time. Back-up sip server support. NAT, Firewall. DHCP client and server. Support PPPoE, (used for ADSL, cable modem connecting). -
Page 6: Compliant Standards
NG-188 User Manual RTP: Real-time Transport Protocol RTCP: Real-time Control Protocol VAD/CNG save bandwidth Telnet: Internet's remote login protocol DNS: Domain Name Server TFTP: Trivial File Transfer Protocol HTTP: Hyper Text Transfer protocol FTP: File Transfer protocol RFC 3362：T.38 protocol Compliant Standards ●... -
Page 7: Installation
192.168.10.x or using dynamic obtain IP. Open your web browser and key in 192.168.10.1. Then you will see the logon page of NG-188, the default username and password is admin/admin for administrator and guest/guest for guest. -
Page 8: Web Configuration
2 Web Configuration 2.1 Access Web setting page Enter NG-188 IP address in the web browser and press ENTER to go to the log on page, and key in the username and password to access NG-188 setting page. Default username and password is:... -
Page 9: Current State
VoIP： show the default protocol, the working state of SIP and IAX2, you can see whether NG-188 has registered the public sip server and IAX2 server. Phone Number shows the public sip server、 the private sip server and the IAX2 server phone numbers. -
Page 10: Network
----Set local DNS server in the Preferred DNS and the Alternate DNS Configure to dynamic obtain IP ----Enable DHCP; If there is DHCP server in your local network, NG-188 will automatically obtain WAN port network information from your DHCP server. Configure PPPoE: ----Enable PPPoE ----PPPoE server: Enter “ANY”... -
Page 11: Lan Config
NG-188 User Manual 2.3.2 LAN Config Bridge Mode: Enable this option to switch to bridge mode. Gateway won’t assign IP for its LAN port in bridge mode and its LAN and WAN port will be in the same network. (This setting won’t take effect unless you save the config and reboot the device) -
Page 12: Voip
Proxy Password: proxy server password Domain Realm: SIP domain, enter the sip domain if any, otherwise NG-188 will use the proxy server address as sip domain. Local SIP port: Local SIP register port, default 5060 Phone Number:... -
Page 13: Iax2 Config
NG-188 will periodically detect whether the public SIP server is available, if the server is unavailable, the NG-188 will switch to the back-up SIP sever, and continue detecting the public sip server. NG-188 will switch back to the primary SIP server if the server is available again. - Page 14 NG-188 User Manual IAX Server Port: Register port of public IAX server，default port is 4569 Account Name: Username of your SIP account (Always the same as the phone number) Account Password: Password of your IAX account. Local port: Signal port of local, default port is 4569...
-
Page 15: Advance
Lease Time: DHCP server lease time. Start IP: Start IP of lease table. End IP: End IP of lease table. Network device connecting to the NG-188 LAN port can dynamic obtain the IP in the range between start IP and end IP. -
Page 16: Nat
NG-188 User Manual 2.5.2 NAT Advance NAT setting. Maximum 10 items for TCP and UDP port mapping. IPSec ALG: Enable/Disable IPSec ALG; FTP ALG: Enable/Disable FTP ALG; PPTP ALG: Enable/Disable PPTP ALG; Transfer Type: Transfer type using port mapping. Inside IP: LAN device IP for port mapping. -
Page 17: Net Service
NG-188 User Manual 2.5.3 Net Service HTTP Port: configure HTTP transfer port, default is 80.User may change this port to enhance system’s security. When this port is changed, please use http://xxx.xxx.xxx.xxx:xxxx/ to reconnect. Telnet Port: configure telnet transfer port, default is 23. -
Page 18: Firewall Settings
Access list support two type limits: input_access limit or output_access limit. Each type support 10 items maximum. NG-188 firewall filter is base WAN port. So the source address or input destination address should be WAN port IP address. Configuration:... - Page 19 NG-188 User Manual Des Mask: Destination address mask. Indicate the source is dedicate IP if set to 255.255.255.255. Otherwise is network ID 19 / 46...
-
Page 20: Qos Settings
NG-188 User Manual 2.5.5 QoS settings AT-530 IP phone implement QoS based on 802.1p, The QoS is used to mark the network communication priority in the data link/MAC sub-layer. AT-530 will sorted the packets using the QoS and sends it to the destination. - Page 21 NG-188 User Manual NG-188 Gateway implement QoS based on 802.1p, The QoS is used to mark the network communication priority in the data link/MAC sub-layer. NG-188 will sorted the packets using the QoS and sends it to the destination. QoS Enable: Enable QoS service.
-
Page 22: Advance Sip Settings
NG-188 User Manual 2.5.6 Advance SIP settings This page is used to set the private sip server, stun server, and back up sip server information. STUN Server setting: STUN Server Addr: configure stun server address; STUN Server Port: configure stun server port default 3478 STUN Effect Time: stun detect NAT type circle, unit: minute. - Page 23 NG-188 User Manual 23 / 46...
-
Page 24: Digital Map
NG-188 support below digital map: Digital Map is based on some rules to judge when user end their dialing and send the number to the server. NG-188 support following digital map: ----End With “#”: Use # as the end of dialing. -
Page 25: Call Service Settings
Enable Call Waiting: Enable/disable Call Waiting Accept Any Call: If this option is disable, NG-188 refuse the incoming call when the called number is different from NG-188’s phone number. No Answer Time: no answer call forward time setting. - Page 26 NG-188 User Manual Black List: incoming call in these phone numbers will be refused. Limit List: outgoing calls with these phone numbers will be refused 26 / 46...
-
Page 27: Mmi Filter
NG-188 User Manual 2.5.9 MMI Filter MMI filter is used to make access limit to NG-188 Gateway. When MMI filter is enable. Only IP address within the start IP and end IP can access NG-188 gateway. 27 / 46... -
Page 28: Audio Settings
NG-188 User Manual 2.5.10 Audio Settings CODEC: select the prefer CODEC; support ulaw, alaw and G729 Signal Standard: Support CHINA, Japan and USA standard Input Volume: Handset in volume. Output Volume: Handset out volume. G729 Payload Length: G729 payload length... - Page 29 NG-188 User Manual protocol .The parameters is as below VPN IP： After VPN registered successfully, VPN server will give an IP aggress to the terminal . If there is a IP address shown on terminal (except for 0.0.0.0) ,it means your...
-
Page 30: Dial-Peer Settings
NG-188 User Manual 2.6 Dial-Peer Settings Please refer to “how to use dial rule?” for detail. 30 / 46... -
Page 31: Config Manage
NG-188 User Manual Config Manage Save Config: save current settings. Clear Config: restore to default settings. Notice: clear config in admin mode, all settings restores to factory default; clear config in guest modem, all settings except sip, advance sip restore to factory default. -
Page 32: Update
2.8.3 Auto update: NG-188 gateway support FTP and TFTP auto update. The gateway will auto obtain the configure file from your update server if configured. To obtain the original configure file, you can use the FTP/TFTP back up as describe above. Configure file using module structure, user may remain the concerned modules and remove other modules. - Page 33 NG-188 User Manual Current Version: the system will display the current version number 。 Server Address: FTP/TFTP server address Username: FTP server user name Password: FTP server password Config File Name: The name of configuration file Config Encrypt Key: The encrypt key of confirmation file...
- Page 34 NG-188 User Manual <GLOBLE CONFIG MODULE> ConfFile Version：7 34 / 46...
-
Page 35: System Manage
NG-188 User Manual 2.9 System Manage 2.9.1 Account Manage Set web access account or keypad password of AT-530. 2.9.2 Phone Book: User may set contacts in this page, and the contacts will be saved in the memory. Then using the Pbook, Vol+,Vol-,Menu/OK and Exit keys to choose your friend in the contacts and then press # to call out. -
Page 36: Time Set
NG-188 User Manual IAX2 Log Level: set the IAX2 log level Please click “apply” after setting 2.9.4 Time Set: Server:type the ip address of time server Timezone:select correct time zone in list box Timeout: longest response time for SNTP Manual Timeset:The time setting Daylight: Daylight Saving time 2.9.3 Reboot:... -
Page 37: Use Normal Phone To Pre-Configure Ng-188 Gateway
NG-188 User Manual Use normal phone to pre-configure NG-188 gateway User may pre-config NG-188 gateway using a normal phone connecting to NG-188. please refer the below command: Notice: all command below can be end with # to speed response. "#****"... -
Page 38: Telnet Console
4.1.1 Basic structure User may use telnet command to access and manage gateway. NG-188 adopts tree structure for telnet. Every node contains its sub-nodes or local command. User can type “help” or “?” whenever to see sub-nodes and all local command under current node. -
Page 39: Global Command
NG-188 User Manual 4.2 Global Command Global command is available under all nodes, NG-188 support following commands: Command Function Example exit Return to parent-node #exit logout Exit #logout ping Ping command, use to check network, #ping www.google.com write Save setting to flash... -
Page 40: Tree Structure
NG-188 User Manual 5 Tree Structure 5.1.1 Debug (Level 0~7) path: <debug># show debug setting ---show [disable]enable debug all modules ---[no] all xxx [disable]enable debug app module ---[no] app xxx [disable]enable debug cdr module ---[no] cdr xxx [disable]enable debug sip module... -
Page 41: Network Diagnosis
NG-188 User Manual uptime path: <show># show running time Example:#<show># uptime version path: <show># show gateway version Example:#<show># version 5.1.4 telnet and logout Usage: #telnet –target -port Login:xxx Password:xxx #logout 5.1.5 tracert trace network path info usage: #tracert –host Example:#tracert www.google.com 6 Network Diagnosis There are some telnet commands for checking your network. -
Page 42: Post Mode(Safe Mode)
How to enter safe mode? In the NG-188 booting procedure, it use the static ip 192.168.1.179 (WAN port IP) for a short time, user can telnet to this ip address in this occasion to enter the save mode.(remember to change your PC into the network 192.168.1.xx ) -
Page 43: Faq
How many SIP servers may NG-188 register simultaneously? NG-188 support 2 SIP servers and a IAX server. The Default server is SIP . If you want to use the IAX server you must set IAX as default protocol in the IAX config page. IAX and SIP can register simultaneously but not work simultaneously. - Page 44 075583018049 and NG-188 will send 8675583018049 to your server. *T rule: Dial the * and the line with switch to PSTN. Note that you need to set another rule “Prefix Number: *; Length: 1” in the Digital Map. (Refer “How to use NG-188’s Lifeline Function?”) 179 rule: when you dial 179 , the call with send to 192.168.1.179, suit for LAN application...
-
Page 45: How To Use Speed Dial Function
NG-188 User Manual How to use speed dial function? Please refer to “How to use dial rule?”. How to configure digital map? Please refer digit map settings. How to use Call Forward, Call Transfer and 3-way Conference calls? User may set up the configuration in the Call Service page to use these value add service. - Page 46 Che k Enable Three Way Call Only sip protocol support this f unction .Assume A is the NG-188 user, and B calls and talking with A through VoIP. A can press Hook-Flash to hold the call with B, then enter C’s number to talk with C, and then press Hook-Flash again switch back to user B , then A can press * to make 3-way conference calls.