Page 2
Consult the dealer or an experienced radio/TV tech- nician for help. FCC COMPLIANCE: The responsible party for this prod- uct’s compliance is: Marketed and Distributed by LG Electronics U.S.A., Inc., 1000 Sylvan Avenue, Englewood Cliffs, NJ. Phone: 1-800-243-0000. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit;...
IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard.
Introduction To ensure proper use of this product, please read this owner’s manual carefully and retain for future refer- ence. This manual provides information on the operation and maintenance of your DVD+VCR. Should the unit require service, contact an Authorized Service Center. Moisture Condensation Never operate the DVD+VCR immediately after mov- ing it from a cold location to a warm location.
Types of Playable Discs (8 cm / 12 cm disc) Audio CD (8 cm / 12 cm disc) In addition, this unit plays DVD-R, DVD+R, DVD-RW, DVD+RW, and CD-R / CD-RW that contains audio titles, MP3, WMA, and/or JPEG files. Notes: •...
Regional Code This DVD+VCR is designed and manufactured for playback of region “1” encoded DVD soft- ware. This unit can play only DVD discs labeled “1” or “ALL”. Notes on Regional Codes • Most DVD discs have a globe with one or more numbers in it clearly visible on the cover.
Front Panel d e f g Disc Tray (DVD deck) Insert a disc here. Cassette Compartment (VCR deck) Insert a video cassette here. 1 POWER Switches the DVD+VCR ON and OFF. . /m - DVD: Skip to beginning of current chapter or track, press twice in quick successions to go to previous chapter or track.
Remote Control Selects numbered options in a menu. b B v V Selects menu options. CH/TRK(v v /V V ) Selects VCR channels. Adjusts manually the tape’s picture onscreen. N (PLAY) Starts playback. Repeats sequence between two points (A and B). SPEED Selects recording speed.
Rear Panel Caution Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. b c d e ANT.IN Connect the VHF/UHF/CATV antenna to this terminal. VCR IN LINE 1 (VIDEO/AUDIO (Left/Right)) Connect the audio/video output of an external source (Audio system, TV/Monitor, VCR, Camcorder).
Connecting an Antenna Connecting an Antenna or Cable TV or Cable TV a Antenna Disconnect the antenna from the rear of the TV and identify the antenna cable. If it is a round 75 ohm coaxial cable connect it directly to the jack marked ANT.IN on your DVD+VCR.
RF coaxial connection Connect the RF.OUT jack on the DVD+VCR to the antenna in jack on the TV using the supplied 75-ohm Coaxial Cable (R). How to set the DVD+VCR’s RF output channel 1. When the DVD+VCR is turned off, press and hold CH (V/v) on the front panel for more than five seconds.
Page 13
Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/Video receiver equipped with a multi-channel decoder (Dolby Digital™, MPEG 2, or DTS) 1. Connect one of the DVD+VCR’s DIGITAL AUDIO OUT jacks (COAXIAL X) to the corresponding in jack on your amplifier.
Initial Settings - VCR Initial Settings - VCR By using the VCR Setup menu, you can make various adjustments to items such as clock setting, and timer recordings. Your DVD+VCR allows Remote Control adjustment of several features. General Operation 1. Press VCR on the Remote Control. 2.
TUNING This DVD+VCR is equipped with a frequency synthesized tuner capable of receiving up to 181 channels. These include VHF channels 2-13, UHF channels 14-69 and CATV channels 1-125. Auto Channel Programming 1. Choose the SOURCE SELECT option, then use b / B to select TUNER.
Initial Settings - DVD Initial Settings - DVD By using the DVD Setup menu, you can make various adjustments to items such as picture and sound. You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 16 to 19.
DISPLAY TV Aspect 4:3 : Select when a standard 4:3 TV is connected. 16:9 : Select when a 16:9 wide TV is connected. Display Mode Display Mode setting works only when the TV Aspect mode is set to “4:3”. Letterbox: Displays a wide picture with bands on the upper and lower portions of the screen.
You can set up the DVD+VCR so a DVD disc auto- matically starts playing whenever the DVD is insert- If Auto Play mode is set to On, this DVD player will search for title that has the longest playback time and then play back the title automatically.
LOCK (Parental Control) Rating Some movies contain scenes that may not be suitable for children to view. Many of these discs contain parental control information that applies to the com- plete disc or to certain scenes on the disc. Movies and scenes are rated from 1 to 8, depending on the area.
Operation This chapter describes how to operate the VCR and DVD. VCR T ape Playback VCR T ape Playback Press the VCR button to select the device to be oper- ated. Basic Instructions 1. Turn on the TV. 2. Tune the TV to the DVD+VCR output channel (CH 3 or 4) or if a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Slow Motion 1. While in still mode, press FORWARD (M). The tape is played at a speed 1/19 times slower than the normal speed. 2. Use CH/TRK (v/V) on the Remote Control if necessary to adjust the tracking. 3. To return to the normal speed, press N (PLAY). Notes: •...
VCR T ape Recording VCR T ape Recording Basic Instructions 1. Turn on the DVD+VCR and TV. 2. Tune the TV to the DVD+VCR output channel (CH 3 or 4) or if a direct VIDEO/AUDIO connec- tion is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Channel: Select a TV channel, LINE1 or LINE2. If you have CABLE TV and use a cable box (con- verter) you must set the channel to match the cable box output channel (usually CH 3 or 4). Change channels on the cable box instead of with the DVD+VCR.
Instant Timer Recording With this feature you can record for a preset length without using the program timer. 1. Turn on DVD+VCR and the TV. 2. Be sure the TV is tuned to the DVD+VCR output channel (CH 3 or 4). If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Copying from DVD to VCR You can copy the contents of a DVD to a VHS tape. 1. Insert the disc you wish to copy into the DVD deck and close the disc tray. 2. Insert a blank VHS video tape into the VCR deck. 3.
Additional VCR Information Additional VCR Information • During manual recording, timer recording, Instant Timer Recording, playback, or fast forward modes, the DVD+VCR automatically starts rewinding the tape at the end of the tape. The cassette stops at the beginning of the tape and is ejected. •...
Playing a DVD Playing a DVD Playback Setup 1. Turn on the TV and select the video input source connected to the DVD+VCR. 2. Turn on the audio system (if applicable) and select the input source connected to the DVD+VCR. 3.
Still Picture and Frame-by-Frame Playback 1. Press PAUSE/STEP (X) during playback. Advance the picture frame-by-frame by pressing PAUSE/STEP (X) repeatedly. 2. To exit still motion mode, press N (PLAY). Search 1. Press BACKWARD ( ) or FORWARD ( during playback. 2.
Last Scene Memory This player memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the player or switch off the player. If you load a disc that has the scene memorized, the scene is automatically recalled.
On-Screen Display - DVD On-Screen Display - DVD You can display the general playback status on the TV screen. Some items can be changed using the menu. To use the on-screen display: 1. Press DISPLAY during playback. 2. Press v / V to select an item. The selected item is highlighted.
Playing an Audio CD or Playing an Audio CD or MP3/WMA Disc MP3/WMA Disc The DVD+VCR can play MP3/WMA formatted record- ings on CD-ROM, CD-R, or CD-RW discs. Audio CD Once you insert an audio CD a menu appears on the TV screen.
Audio CD and MP3 / WMA Audio CD and MP3 / WMA Disc Features Disc Features Pause 1. Press PAUSE/STEP (X) during playback. 2. To return to playback, press N (PLAY) or press PAUSE/STEP (X) again. Moving to another Track 1.
Programmed Playback Programmed Playback The program function enables you to store your favourite tracks from any disc in the player memory. A program can contain 30 tracks. 1. Insert a disc. AUDIO CD or MUSIC menu appears. 2. Press PROGRAM. mark will appear to the right of the word “Program”...
iewing a JPEG Disc iewing a JPEG Disc Using this DVD+VCR you can view discs with JPEG files. 1. Insert a disc and close the tray. The PHOTO menu appears on the TV screen. 2. Press v / V to select a folder, and press ENTER. A list of files in the folder appears.
Controlling other TVs with the remote You can control the sound level, input source, and power switch of non-LG TVs as well. If your TV is list- ed in the table below, set the appropriate manufactur- er code. 1. While holding down TV POWER button, press the number buttons to select the manufacturer code for your TV (see the table below).
Language Codes Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu. Language Code Language Abkhazian 6566 Fiji Afar 6565 Finnish Afrikaans 6570 French Albanian 8381 Frisian Ameharic 6577 Galician Arabic 6582 Georgian Armenian...
roubleshooting roubleshooting Check the following guide for the possible cause of a problem before contacting service. Symptom The power cord is disconnected. No power. The power is on, but DVD or VCR button is not switched the DVD+VCR does properly. not work.
Page 38
Symptom The DVD+VCR does An unplayable disc is inserted. not start playback. The disc is placed upside down. The disc is not placed within the guide. The disc is dirty. The Rating level is set. Is the cassette compartment empty? Video tape cannot be inserted.
Specifications Specifications General Power requirements 120V, 60 Hz Power consumption 16 W Dimensions (approx.) 16.9" X 3.1" X 10.4" (430 X 78.5 X 265 mm) (w x h x d) Weight (approx.) 9.24 lbs (4.2 kg) Operating temperature 5˚C to 40˚C (41˚F to 104˚F) Operating humidity 5 % to 90 % Signal system...
Page 40
LG, software errors that do not disable function- ality, operating and software protocols adopted after the date of manufacture or for outside the US, institutional or commercial use, or other causes not arising out of defect in material or workmanship.