Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pixsys TD570
Summary of Contents for Pixsys TD570
- Page 1 PANNELLO OPERATORE TOUCH SCREEN TD570 - TD700 Manuale operatore...
-
Page 2: Table Of Contents
Dimensions and installation ............. 3 Hardware data ................. 6 Mechanical features ............... 6 Standard Hardware configuration ..........6 Display and Lamp TD570 .............. 6 Display and Lamp TD700 .............. 6 Connections ................... 6 Electrical wirings ..............8 Terminal block M1 ............. 9 Ethernet connection ............ -
Page 3: Introduction
1 Introduction Thanks for choosing a Pixsys device. TD570/TD700 is a Touch-screen graphic Terminal and HMI, Windows-CE based. Sealing of front panel according to IP54, box sealing according to IP30. 2 Ordering codes TOUCH PANEL 5,7” - 640x480 TD570-AD Power supply 12..24V AC/DC ±15% 50/60Hz TOUCH PANEL 7”... - Page 4 179 mm Dima di foratura 180 x 144 mm Frontal panel cut-out Spessore suggerito 2 9 mm ÷ Suggested thickness M emory Card (op t ional) Cod. CARD SD 32mm 32mm inserimento insert Memory Card Memory Card 204 mm Es p ans ione (op t ional) Cod.
- Page 5 179 mm Dima di foratura 180 x 144 mm Frontal panel cut-out CARD Spessore suggerito 2 9 mm ÷ Suggested thickness Memory Card (optional) Cod. CARD SD 32mm 32mm inserimento insert Memory Card Memory Card 204 mm Espansione (optional) Cod. ETD884-AD...
-
Page 6: Hardware Data
5 Hardware data Mechanical features Front panel dull anodized aluminium 8mm Standard Hardware configuration ARM V4i 200 MHz Audio AC ’97 SoundMAX® Codec Display and Lamp TD570 Type LCD TFT touch screen Dimensions Active area 5.7” Resolution 640 x 480 Pixel dimension 0.18 x 0.18 mm... - Page 7 I/O Port 2 rear USB port 2.0 12 Mbits/S 150mA Audio 1 line Out Power supply 12..24V AC/DC ±15% 50/60Hz Power consumption Typical 3,7 W Max 4,8 W...
-
Page 8: Electrical Wirings
Separate control lines from power wires • Avoid proximity of remote control switches, electromagnetic meters, powerful engines • Avoid proximity of power groups, especially if phase-controlled View of connectors on TD570-AD and TD700-AD: CARD USB Device DIP2 DIP3 DIP1 COM1... -
Page 9: Terminal Block M1
6.1 Terminal block M1 Positive power supply of device Ground power supply of device Rs485+ opto-isolated Rs485+ opto-isolated Isolated ground for serial CAN H opto-isolated serial CAN L opto-isolated serial 6.2 Ethernet connection Connector RJ45 DIP2 DIP3 DIP1 COM1 USB1 ETH1 USB2-2... -
Page 10: Usb Connections
Ethernet Connector 10/100 Base-T available on rear side of Terminal, below terminal block of power supply. It allows to connect the device to local network. Green led indicates that link is available and device is connected to network. Yellow led indicates that data transmission/receipt is in progress. 6.3 USB connections The device is provided with two USB 2.0 connectors. -
Page 11: Com1 Rs232 Connector
The connector on front panel allows to connect plug&play peripheral devices also when the Terminal is panel-mounted. USB Peripheral devices include keyboards, mouse, serial converters, barcode readers etc. Max current available on USB connector is 150mA. If using pendrives, the system will rename “Harddisk” the first inserted pendrive and “Harddisk2”... - Page 12 Request To Send RS485 + (B)
-
Page 13: Audio Connector
6.5 Audio connector Audio Jack 3.5mm A non-amplified stereo output is located on the right side of the device. 6.6 SD/MMC connector SD/MMC reader, push-pull type CARD USB Device... -
Page 14: Usb-Device Connector
The connector is located on the upper side of the device , close to mini-usb connector. It is push-pull type, therefore enter memory card till a click is produced and release it (see diagram below ). To extract the Memory, press it until a click is produced and pull it. The device can support SD and MMC memories up to 2GB, it does not support SD-cards HC. -
Page 15: Etd-Exp Connector For Data Acquisition Modules
ETD-EXP connector for data acquisition modules Connectors for data acquisition modules : DIP2 DIP3 DIP1 COM1 USB1 ETH1 USB2-2 The “ETD-EXP1” “ETD-EXP2” connectors allow quick connection of proprietary expansion slots for data acquisition purpose. Please proceed as follows: Switch the device off, disconnect power supply, enter the expansion slot , fix the four screws contained in the package, connect power supply and switch the device on. -
Page 16: Setting Of Dip-Switches
Example of connection ETD884-AD: CARD 7 Setting of dip-switches TD570/TD700 are provided with some internal dip-switches (which may be accessed by special holes on the enclosure), allowing the user to adapt the device to specific requirements. N.B.: Switch the device off and disconnect power supply... -
Page 17: Serial Dip-Switches
7.1 Serial dip-switches DIP1 is conceived to set the serial communication. It is placed underneath power supply terminal block, therefore the terminal block must be removed in order to get access to DIP1. The following table shows the optional settings of this dip-switch: Input type Dip- Notes... -
Page 18: Cpu Dip-Switches
Chiude tra linee CANH e CANL una resistenza di terminazione di Termination 120 Ohm. Close a termination resistor RS485 330Ohm between RS485+ and Termination RS485- Polarization Close polarization resistors on RS485 RS485 line If the device is used as Master RS485, the dip-switches will have to be set as “RS485 polarization”. - Page 19 Input type Dip-switch Notes Default position: configuration for Default TD570/TD700. Prevent Raising “DIP2” to ON , the writing writing on on flash memory is not allowed. flash memory N.B.: Dips no. 1, 3 and 4 are directly connected to CPU and...
-
Page 20: Com1 Dip-Switches
tampering may affect the correct operation of the Touch- screen! 7.3 COM1 dip-switches "DIP3" dip-switch allows selection between debug serial port (to be used for software developments) and system COM1 serial port. Both serial ports are available on 9poles connector with RS232 protocol. -
Page 21: Connecting The Terminal To Pc
Windows-based PC. To connect the device to a PC, it is necessary to get a USB type A - mini USB type B cable (Pixsys code 1620.00.082) and the software ActiveSync (for Windows 2000 up to Windows XP) or alternatively the Windows Mobile Device Centre (for Windows Vista and Windows 7). - Page 22 Windows 2000..Windows XP Windows Vista and Windows 7 By means of these software tools, the device is identified by the PC as a mass storage peripheral and this way it will be possible to explore files and transfer them from PC to device and viceversa.
-
Page 23: Connection By Ftp
8.2 Connection by FTP TD570/TD700 support FTP protocol and this allows network files transfer between PC and Terminal. To access the folders on the device, just open “Explorer” and type: “ftp://anonymous:anonymous@192.168.0.100” (being “192.168.0.100” the IP address of the device). To get the IP address of the device just double-click on network icon on Windows taskbar. - Page 24 Anyway we suggest to use an FTP client for data transfer, as this is normally simpler and quicker to use. An example is FileZilla Client FTP, available for free download at http://filezilla-project.org/download.php...
-
Page 25: Remote Desktop
8.3 Remote desktop The device is integrating Remote Desktop feature. This requires “cerdisp.exe” to be run on the device (it is already pre-installed on it) and “cerhost.exe” to be run on PC. As a first step the device must be connected to local network, then double-click the desktop “Cerdisp”... -
Page 26: Auto-Start Of Selected Applications
At this stage run the “cerhost.exe” application on the PC which will be used to control the TD430. A window with different options will be displayed , click on “File” and then on “Connect”. A further window will show in a few seconds a list of devices available for connection. -
Page 27: Create Autorun.lnk File
on the device and will start the application pointed by the autorun.lnk available on the root of the USB peripheral or of the memory card. 9.1 Create autorun.lnk file N.B.: Whenever an application is run automatically by autorun, Windows desktop is not run. Therefore if the running application should be closed, the device will still display the latest window. - Page 28 Go to the device root (nandflash) or to USB peripheral (Harddisk) and click “Edit” and “Paste Shortcut”. Open video keyboard and rename the Autorun file Restarting the device, the application pointed by the created Autorun file will automatically start.
-
Page 29: Installation Program
10 Installation program Software applications to be installed on TD570/TD700 must be compatible with Windows CE for ARM V4i platform Usually these applications are provided as a single installation file with .CAB extension. The installer service already stored on the device will automatically recognize the installation package and will guide the user step by step through the correct proceeding. - Page 30 The “VS2005tcp.exe” application allows to connect the device by Ethernet connection to development environment Visual Studio 2005. All described applications are available for immediate access on desktop of the device.
-
Page 31: Notes / Updates
12 Notes / Updates... - Page 36 PIXSYS srl www.pixsys.net e-mail: sales@pixsys.net support@pixsys.net 2300.10.135 - Rev. A 031210 *2300.10.135*...
Need help?
Do you have a question about the TD570 and is the answer not in the manual?
Questions and answers