EMX CR-2000 Instruction Manual
Keypad/card reader
Hide thumbs
Also See for CR-2000:
- Instruction manual (11 pages) ,
- Operating instructions manual (13 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for EMX CR-2000
Summary of Contents for EMX CR-2000
- Page 1 CR-2000 Keypad / Card Reader Instruction Manual Read instructions carefully before installation...
- Page 2 The CR-2000 has low power consumption (30mA standby) luminous keypad for nighttime use, Short circuit protection, tamper alarm output, and the Wiegand output for monitoring of user access. The CR-2000 may also be used stand alone for access control of doors, gate and barrier arms. Features •...
- Page 3 Door Unlock settings / Alarm Time settings User Operation / Administrator Page 5 Restore Factory settings Page 6 Audio / Visual Indicators Page 6 Packing list / Accessories / User Notes Page 7 Contact and Warranty Information Page 8 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 4 AC/DC - BLACK POWER 9 – 28V DC – input BLUE RELAY INTERNAL CONTACT (normally open) PURPLE RELAY INTERNAL CONTACT (common) ORANGE RELAY INTERNAL CONTACT (normally closed) SHIELD GROUND (earth ground) Figure 2.0 Page 1 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 5 Figure 2.1 Figure 2.2 Page 2 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 6 ID number # password # Press , … This is for users with pass code only no cards. Code may be any four digit combination except for (1234, this is reserved by the system). Page 3 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 7 8. Security Mode 8.1 Press Normal (factory default) 8.2 Press Invalid Lock Within 10 minutes multiple swipes of invalid card or input of invalid pass code 10 times the internal and external alarms will trigger. Page 4 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 8 9 more attempts before unit locks and needs reset by administrator or valid card swipe and correct password entry. 11. Administrator Functions Enter administrator password # 11.1 Remove Alarms See section 1 page 3 11.2 Administering users, passwords, alarm settings, timing functions Page 5 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 9 12.1 Disconnect power 12.2 Remove the back cover 12.3 Use shorting jumper across the reset pins (figure 3.0) 12.4 Restore power 12.5 The CR-2000 will beep twice 12.6 Remove shorting jumper Note: Restoring to factory setting will not delete user(s) data.
- Page 10 For mounting Star Wrench 20mm x 60mm For Tamper resistant screw Star screws M3 x6mm Tamper resistant screw Accessories CR-2000 Card Reader / Keypad 2000 users CARX-20 1.8mm Mifare User Notes Master Password Page 7 CR-2000 Instructions Revision 1.0 02/20/2013...
- Page 11 EMX Industries, Inc. sole responsibility and liability, and the purchaser’s exclusive remedy shall be limited to the repair or replacement at EMX Industries option of a part or parts found not conforming to the warranty. In no event shall EMX Industries, Inc. be liable for damages of any nature, including incidental or consequential damages, including but not limited to damages resulting from non-conformity, defect in material or workmanship.
- Page 12 CR-2000 Instructions Revision 1.0 02/20/2013...
Need help?
Do you have a question about the CR-2000 and is the answer not in the manual?
Questions and answers