Table of Contents
Related Manuals for Syris SYRDF5
Summary of Contents for Syris SYRDF5
-
Page 1: User Manual
SYRDF5/F6 Stand Alone Fingerprint/Proximity Reader User Manual April, 2008 Ver: 1.00 SYRIS Tech. Corp, 21F-2,NO 12,Sec. 1,Taijunggang Rd Taichung,Taiwan(403),R.O.C. TEL：886-4-2207-8888 FAX：886-4-2207-9999 Email：service@syris.com... - Page 2 Stand Alone Fingerprint/Proximity Reader Device Shape Notice：Communication interface is RS485 © 2008 by SYRIS Technology Corp.
-
Page 3: Operation Procedure
OK starts glittering, user can flash the card that is prepared to record. 2-2.When the device starts beep, move off the card. When the LED light of starts glittering 3 times, the process of Add Card is done. ！ © 2008 by SYRIS Technology Corp. -
Page 4: Delete Fingerprint
！ 4-3.When the device beeps one time, you need to move off the card (the light of OK will glittering one time). The light of shut down, all the ！ process will be done. © 2008 by SYRIS Technology Corp. - Page 5 6-3.When the LED light of OK stops glittering, it means the fingerprint is erased correctly. User can move off finger. © 2008 by SYRIS Technology Corp.
- Page 6 “beep”. The led light of OK will light 2 mins continuely. 7-2.When the light of OK turn off, it means th procedure is finished. Note：Please do not set Duplicated Card/Fingerprint in the same device. © 2008 by SYRIS Technology Corp.
- Page 7 (especially in rainy day or deal with oil by using towel first then material). press sensor. Finger is too dry. Please re-press the finger or make it moister. Finger hurt after capturing Please re-capture fingerprint. fingerprint. © 2008 by SYRIS Technology Corp.
-
Page 8: Emergency Response
Emergency Response Once the Master Card was lost or stealed, please reset a new master card via Reader_Tools. Original one will be erased by device, the level of security is high. Please activate the software © 2008 by SYRIS Technology Corp. - Page 9 Stand Alone Fingerprint/Proximity Reader Step 1. Click the tab of SYRDF5-M1/F6-M1 Step 2. Click the button of Scan reader then the title will be shown ”Reader find ok. (COM : # com port number )” Step 3. Click Fingerprint Step 4. Click Set stand alone mode Step 5.
- Page 10 1、Finger is not touch the sensor fully. 2、Finger is not touch the center of sensor. 3、Finger is not pressed with full strength. 4、Finger press is out of valid scop of sensor. Correct Fingerprint enrollment： © 2008 by SYRIS Technology Corp.
- Page 11 The approach of catching fingerprint is the same as the picture. The system will identify fingerprint via template that is captured from the center of the finger then spread to full fingerprint. © 2008 by SYRIS Technology Corp.
- Page 12 Stand Alone Fingerprint/Proximity Reader SYRDF5 MOUNTING PLATE © 2008 by SYRIS Technology Corp.
- Page 13 SYRDF6 MOUNTING PLATE...
- Page 14 83W x 121H x 45D / 91 W x 146 H x 61 D * This specification is preliminary and is subject to change without prior notice. * Reading range is subject to card type, site interference and antenna specs for more information. © 2008 by SYRIS Technology Corp.
- Page 15 Stand Alone Fingerprint/Proximity Reader SYRDF5 WIRING DIAGRAM * Power supply should be regulated linear power supply. * Your system must have a single earth ground point. * The shield must run continuous throughout the installation. <Enlarge> © 2008 by SYRIS Technology Corp.
- Page 16 Stand Alone Fingerprint/Proximity Reader SYRDF6 WIRING DIAGRAM * Power supply should be regulated linear power supply. * Your system must have a single earth ground point. * The shield must run continuous throughout the installation. <Enlarge> © 2008 by SYRIS Technology Corp.
- Page 17 SYRDF5 WIRING DIAGRAM...
- Page 18 Stand Alone Fingerprint/Proximity Reader SYRDF6 WIRING DIAGRAM © 2008 by SYRIS Technology Corp.
Need help?
Do you have a question about the SYRDF5 and is the answer not in the manual?
Questions and answers