Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Huacam HCV701
Summary of Contents for Huacam HCV701
- Page 1 HUACAM, Inc. HCV701 User Manual www.huacam.com www.huacam.com...
-
Page 2: Table Of Contents
HCV701 Camera ......................6 HCV701 Specifications ....................7 Installation guide ........................8 Minimum Recommended Computer System Requirement.......... 8 Configure the HCV701 via Web Browser ..............8 HCV701 Home Web Page..................12 HCV701 Configuration & Language Page..............14 Basic settings explanation ..................... 15 4.1. -
Page 3: Welcome
HC_Surf, It is fully compliant with ONVIF standard and offers flexible HTTP API and an SDK for advanced integration. The HCV701 Outdoor Day/Night IP camera is a new addition to the popular HCV70X series IP surveillance product family. It ensures ease of use, integration and deployment, with multilingual graphical user interface, provides powerful solution to professional surveillance applications in outdoor environment. -
Page 4: Safety Compliances
1.1 Safety Compliances These instructions are intended to assist users with the operation of the HCV701 and also to instruct on how to avoid dangerous situations or damage to the device. Warnings: Serious injury or death may be caused if any of the warnings below are neglected. -
Page 5: Warranty
User Manual, could void your manufacturer warranty. Please do not use a different power adaptor with the HCV701 as it may cause damage to the products and void the manufacturer warranty. -
Page 6: Product Overview
2. Product overview 2.1 HCV701 Camera NETWORK : 10/100 Switch LAN port for connecting to Ethernet. RST: Reset button LINE IN: 3.5mm Audio LINE IN(Write) LINE OUT: 3.5mm LINE OUT(Green) DC 12V : 12V DC power jack; www.huacam.com... -
Page 7: Hcv701 Specifications
2.2 HCV701 Specifications Model HCV701 Video Compression H.264, MJPEG Image Sensor Resolution 1/3”, CMOS, 1280H x960V Image Sensor Sensitivity Day & night mode, exceptionally low noise levels and low-light sensitivity. Shutter: 1/10000 – 1/30 second Focal Length 2.8mm Aperture F1.8... -
Page 8: Installation Guide
3. Installation guide Minimum Recommended Computer System Requirement To install HCV701, you have to have a computer, PC recommend. The minimum recommended PC system requirement listed below: • Windows 2000, XP, Windows Vista, Windows 7 (32bit or 64bit) • CPU: Intel Pentium 4 or higher, 2 GHz •... - Page 9 Connect the Camera to network with DHCP server (Recommended) The HCV701 by default enabled as DHCP client, it will automatically get IP address from the network with DHCP server running. User can know the IP address assigned to the camera from DHCP server log or using “SearchTool”...
- Page 10 9. In step 6, IE will indicate that “This website wants to install the following add-on: HCViewerX.cab from Huacam Networks Inc.”, allow the installation. 10. Firefox user need to download and install the plug-in to see the video, the plug-in for Firefox is here: http://www.huacam.com/index.php?option=com_jdownloads&Itemid=103&view=finish&cid=5&cat...
- Page 11 The default IP, if no DHCP server; or DHCP offer time out (3 minutes), is 192.168.1.168 1. Connect the computer RJ-45 via an Ethernet cable directly to the IP camera HCV701 . 2. Configure the computer using Static IP: 192.168.1.XXX (1<XXX<255, but NOT 168) and configure the “Subnet mask”...
-
Page 12: Hcv701 Home Web Page
NOTE: Please temporarily disable Antivirus or Internet Security Software when download and install the Huacam Firefox plug-in for video or “GSViewerX.cab” for Microsoft Internet Explorer. HCV701 Home Web Page The Home Page of HCV701 shown as Figure 1: www.huacam.com... - Page 13 Zoom in or Zoom out during ePTZ operation. 3. FOCUS: Adjust the focus of image (Not Applicable to HCV701 ). 4. PTZ SPEED/Default Button: Adjust the rotate speed of the control console (Not Applicable); “D” “Default Button” to reset the video brightness, contrast and saturation value from (auto or manual) adjusted value to factory default value.
-
Page 14: Hcv701 Configuration & Language Page
18. Motion Detection Alarm Indicator: If motion detection alarm triggered, the indicator will flash in red. 3.4 HCV701 Configuration & Language Page • When click the “Configuration” tab, web page will link to page to configure the related parameters of the HCV701 . -
Page 15: Basic Settings Explanation
4. Basic settings explanation 4.1. System Settings Page This page allow user to configure the system settings of HCV701 . Figure 3: System Settings Page Current System Time: Display time current system is running at Set the System Time: Configure the time system is running. -
Page 16: Video & Audio Setting Page
Networking button has to be clicked to save all the changes made to the device. 4.2. Video & Audio Setting Page This page allows user to configure the video and audio related settings. Figure 4-1: Video & Audio Settings Page www.huacam.com... - Page 17 Audio Settings: • Microphone Volume : Slide to adjust microphone gain. • Speaker Volume: Slide to adjust the built-in speaker volume. Power Frequency: Select correct local power frequency to avoid video flicking effect under fluorescence light condition. Default is Outdoor. www.huacam.com...
-
Page 18: Cmos Settings Page
If MJPEG selected, reduce max. frame rate to min. value to save bandwidth and get better image Huacam IP Camera provides two video streams, user can use them with flexibility. For example, the high-resolution stream for local recording; another low or high resolution for remote monitoring;... -
Page 19: Networking Setting Page
• Color Mode: Camera Color Mode. There are three options: Color; Black/White; Auto. NOTE: Auto option recommended for Shutter Speed, IR CUT Setting and Color Mode. 4.4. Networking Setting Page This page allows user to configure network related parameters: www.huacam.com... - Page 20 In addition to HTTP port, RTSP port also required to be configured for port forwarding, in order for remote party viewing the H.264 video. If change the default port from TCP 80 to port “A”, then RTSP port should be “2000+A”. Both www.huacam.com...
-
Page 21: Ddns Settings Page
• Site Name: DDNS site name • DDNS Account: DDNS account name • DDNS Password: DDNS password • STUN Server: Stun server FQDN or IP. If device behind a non-symmetric router, STUN server can help to penetrate & resolve NAT issue. www.huacam.com... -
Page 22: Sip Setting Page
This page allows user to configure SIP related parameters. HCV701 can be configured as SIP endpoint to call out when alarm trigged; or allow permitted number to call in to check the video if Huacam video IP phone is used. - Page 23 Auto On Hook timer, default 300 seconds • Disable Audio in SIP Call: Checked to disable audio for SIP call • Enable Keep Alive: Checked to enable, help NAT resolution • Accept Direct IP Call: Check to accept peer to peer IP call. www.huacam.com...
-
Page 24: Status Page
• Enable Dual-way Audio Warning: Check to enable two-way audio warning. • Phone List/Phone Number: Callee or call receiver number when alarm call trigged. • White List/Phone Number: Phone numbers allowed to call into the camera. 4.7. Status Page This page shows the HCV701 operation status: www.huacam.com... -
Page 25: Advanced Settings Explanation
Figure 9: Status Page NOTE: When SIP account registered, the status will display “Online” in Green. When SIP account unregistered, the status will display “Offline” in Red, as below. 5. Advanced settings explanation The supports all the traditional and advanced telephony features. www.huacam.com... -
Page 26: User Management Page
• Allow Anonymous Viewing: When checked, no security enhanced. Any person can view the camera if knowing the IP or FQDN of the camera, but can NOT change anything, just view ONLY. 5.2 Maintenance Page This page allows user to maintain the camera: www.huacam.com... - Page 27 Server path holding the configuration file (auto provisioning) • XML ConfigFile Password: Password for encrypt the XML based configuration file • Automatic Upgrade Interval (Minutes): Time interval for automatic upgrade, default 10080 • Automatic Upgrade: Checked to enable automatic firmware upgrade and provisioning. NOTE: www.huacam.com...
-
Page 28: Smtp Setting Page (Email Alarm)
Only XML based automatic provisioning is supported by HCV701 . 5.3 SMTP Setting Page (Email Alarm) This page allows user to configure email client to send out email when alarm trigged: Figure 12: SMTP Setting Page • Enable SMTP: When checked, email client is enabled. -
Page 29: Ftp Settings Page (Upload Alarm)
When checked, built-in FTP client is enabled. • FTP Server: IP or Domain name of FTP site or server • FTP Server Port: TCP port for FTP server, default port number 21 • User Name: FTP server User ID • Password: FTP server user password www.huacam.com... -
Page 30: Alarm Server Settings Page (Upload Alarm To Supported Vms Or Http Server)
Figure 14: Alarm HTTP Server Setting Page • Server Name: The name of HTTP server or VMS system • URL: URL of the Server • User Name: User ID from that Server • Password: Password for that User ID www.huacam.com... -
Page 31: Motion Detection Configuration Page (Set Alarm)
NOTE: Huacam provide HTTP API to help 3 party company by using HTTP server or VMS to develop further solutions for its customers. Huacam IP Camera are ONVIF certified. 5.6 Motion Detection Configuration Page (Set Alarm) This page allows user to configure motion detection to trigger alarms: Figure 15-1: Motion Detection Configuration Page •... -
Page 32: Motion Detection Time Schedule
• Upload to Alarm HTTP Server When checked, the alarm will be sent to Alarm HTT Server. Party Server also can be used via HC HTTP API NOTE: Huacam free HC_Surf VMS software can be downloaded here: http://www.huacam.com/index.php?option=com_jdownloads&Itemid=103&view=finish&cid=4&cati • Email and FTP upload JPEG: When checked, a snapshot of trigger moment will be generated and be emailed to pre-configured email account, also upload to FTP server if configured. -
Page 33: Syslog Settings Page (Troubleshooting)
As shown in Figure 15-2, user can configure the Motion Detection Region with related Start and Stop time to control the motion detection operation. 5.8 Syslog Settings Page (Troubleshooting) This page allows user to enable the Syslog to help troubleshooting problems: Figure 16: Alarm Server Setting Page www.huacam.com... -
Page 34: Software Upgrade
Software upgrade can be done via either TFTP, HTTP or HTTPS. The corresponding configuration settings are in the ADVANCED SETTINGS configuration page. 5.10 Software Upgrade via TTFP, HTTP or HTTPS This page allows user to configure firmware upgrade: Figure 17: Firmware Upgrade and Provisioning www.huacam.com... -
Page 35: Instructions For Local Firmware Upgrade Using Tftp Server
Microsoft IIS web server. 5.12 Configuration File Download Huacam SIP Device can be configured via Web Interface as well as via Configuration File through TFTP or HTTP/HTTPS. “Config Server Path” is the TFTP or HTTP/HTTPS server path for configuration file. It needs to be set to a valid URL, either in FQDN or IP address format. The “Config Server Path”... -
Page 36: Restore Factory Default Setting
Restoring the Factory Default Setting will DELETE all configuration information of the camera. Please BACKUP or PRINT out all the settings before approach to following steps. Huacam will not take any responsibility if you lose all the parameters of setting or cannot connect to your VoIP service provider. -
Page 37: Ip Surveilance Faq
The HCV701 web configuration page is not displayed correctly in IE8 ? In IE8, Compatibility View might need to be enabled for the HCV701 web configuration page to load properly. To enable compatibility view, open IE8, click Tools, Compatibility View Setting, and add theHCV701 web configuration pages to the Compatibility View. - Page 38 Make sure that the RTSP port of the device is set to 2000 plus the HTTP Port number. For example, if the HTTP port is 88, then the RTSP port of the device that you configured on HC_Surf or mobile phone should be 2088. www.huacam.com...
- Page 39 RTSP port number changes according to the web port. If the web port is 80, then the RTSP port is 554. If the web port is not 80, then the RTSP port equals the web port +2000. For example, if the web port is 88, then the RTSP port will be 2088. www.huacam.com...
- Page 40 HUACAM Huacam Technology Co., Ltd Tel (+86)0755-28178617 Web www.huacam.com Support: support@huacam.com Sales: sales@huacam.com www.huacam.com...
Need help?
Do you have a question about the HCV701 and is the answer not in the manual?
Questions and answers