Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EYEsurv ESIP-MP3-BTZF1
Summary of Contents for EYEsurv ESIP-MP3-BTZF1
- Page 1 HD IR Waterproof Fixed Network Camera Quick Start Guide Version 1.0.0...
- Page 2 Welcome Thank you for purchasing our network camera! This quick start guide is designed to be a reference tool for your system. Please keep this start guide well for future reference. Please open the accessory bag to check the items one by one in accordance with the list below. Contact your local retailer ASAP if something is missing or damaged in the bag.
- Page 3 Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera. 6. Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work.
-
Page 4: Table Of Contents
Table of Contents Framework........................1 Multiple-function Combination Cable..............1 Framework and Dimension ................2 Bidirectional talk ....................3 1.3.1 Device-end to PC-end................. 3 1.3.2 PC-end to the device-end ................3 Alarm Setup ...................... 3 Device Installation ......................5 Device Installation ..................... 5 Install Micro SD Card .................. -
Page 5: Framework
1 Framework 1.1 Multiple-function Combination Cable You can refer to the following figure for multiple-function combination cable information. See Figure 1-1 Figure 1-1 Multiple-function combination cable Please refer to the following sheet for detailed information. Port Name Function Connection Note Power port. -
Page 6: Framework And Dimension
Port Name Name Note ALARM_COM Alarm output public port. Alarm output port. It is to output the alarm signal to the alarm device. ALARM_NO NO: normal open alarm output port. It shall work with ALARM_COM port. I/O Port Alarm input port 1. It is to receive the on-off signal ALARM_IN1 from the external alarm source. -
Page 7: Bidirectional Talk
1.3 Bidirectional talk 1.3.1 Device-end to PC-end Device Connection Please connect the speaker or the MIC to the audio input port of the device. Then connect the earphone to the audio output port of the PC. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the bidirectional talk function. - Page 8 Figure 1-4 Alarm Please refer to the following figure for alarm input information. See Figure 1-5. Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the logic “1”.
-
Page 9: Device Installation
2 Device Installation 2.1 Device Installation Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference. Step 1. Dig three holes in the wall or the surface, and then input the three expansion bolts to the holes and secure. -
Page 10: Adjust Lens
Figure 2-2 Micro-SD card 2.3 Adjust Lens Rotate lens counterclockwise, and take it down. You can see its front and rear adjusting rod. Front rod adjusts focus while rear rod adjusts zoom. After adjusting rod, rotate lens cover clockwise to fasten it. See Figure 2-3. Note: ... -
Page 11: Adjust Bracket
Figure 2-3 Adjusting lens 2.4 Adjust Bracket You adjust bracket with a M4 inner hex screw. Before adjustment, you loosen the screw with inner hex wrench in accessories bag. Rotate rear cover 360°horizontally, and 90°vertically. Rotate pedestal 360°. Secure the screw with inner hex wrench after adjustment. See Figure 2-4. Note: M4 inner hex wrench must be secured, otherwise the pedestal will be unstable and device cannot be fixed to specific angle. -
Page 12: Button
Figure 2-4 Adjusting bracket 2.5 Button You can switch button to up/down to zoom in/out. You also can switch button to left/right to focus. Long press button for 2s for auto focus which makes video clear. See Figure 2-5 and 2-6. Note: The button is for motorized series only. - Page 13 Figure 2-5 Button Position Figure 2-6 Button...
-
Page 14: Quick Configuration Tool
3 Quick Configuration Tool 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”... - Page 15 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 3-1), please select a device IP address and then double click it to open the login interface.
-
Page 16: Web Operation
4 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. ... - Page 17 Figure 4- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 4- 3. Figure 4- 3 Web monitoring window...
-
Page 18: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Cr VI PBDE ○ ○ ○ ○ ○ ○ Circuit Board Component ○ ○ ○ ○ ○ ○ Device Construction Material ○ ○ ○ ○ ○...
Need help?
Do you have a question about the ESIP-MP3-BTZF1 and is the answer not in the manual?
Questions and answers