Identification Of Controls; Front Panel - NAD M50 Owner's Manual

IDENTIFICATION OF CONTROLS

FRONT PANEL

1 2
1 STANDBY LED
•
This indicator will light up amber upon switching ON the rear panel
POWER switch.
•
When the front panel Standby button is pressed to power up the
M50 from standby mode, this indicator will illuminate blue.
2 STANDBY BUTTON
The rear panel POWER switch must be at ON position for the Standby
button to activate. Pressing the Standby button will result to varying
actions or responses and is best illustrated by the table below.
ACTION/RESPONSE
STANDBY BUTTON STANDBY LED
After switching ON the rear Turns from amber
panel POWER button, press to blue.
from standby mode.
With M50 already powered Remains illuminated
ON, toggle button. in blue.
Press and hold... until Flashing amber and
Standby LED turns to solid then turns to solid
amber. amber.
With the M50 at standby Turns from amber
mode, press Standby button to blue.
or any front panel button.
3 INPUT
Switch input Sources when available. Toggle INPUT button to select
through the following Sources
•
USB - Playback music files from the USB mass storage device
connected to Front USB.
•
Library - Makes available songs from shared computer, NAS,
connected USB mass storage device or M52.
•
Audio/Data disc - Playback loaded audio or data disc.
4 STOP/OPEN
Pressing STOP/OPEN during disc playback will cause the M50 to stop
playback and then eject the loaded disc.
5 DISC SLOT
•
Insert CD or audio disc face down into this slot and playback will
automatically start provided the M50 is not connected to an active
M52 or USB mass storage device.
• CD will not playback automatically if a playlist is already available or
active at the time of CD loading. Select Audio Disc source to browse
and playback CD content.
• Refer also to "RIP/ENCODE CONTROL PANEL" section below for Rip/
Play options when an audio CD is inserted.
8
stop/
input open
3 4 5
RESULT
M50 is powered up.
VFD is illuminated.
M50 remains ON.
VFD is turned on or off.
M50 switches to
standby mode.
VFD is turned off.
M50 is powered up.
VFD is illuminated.
digital music player
play/
pause
6 7 8
IMPORTANT NOTES
• The M50 must stand-alone, i.e. not connected to an active M52 or USB
mass storage device, for a loaded CD to be automatically played back.
• Only Audio CD can be played back by a stand-alone M50. If a data disc
(CD-R/RW with data files) is inserted into the disc slot, select "Data Disc"
source to browse and playback music file contents.
6 VACUUM FLUORESCENT DISPLAY (VFD)
Display visual information about the current Source. Information
supplied is generated by the Source.
7 REMOTE SENSOR
•
Point the remote control at the remote sensor and press the
buttons.
•
Do not expose the remote sensor of the M50 to a strong light
source such as direct sunlight or illumination. If you do so, you may
not be able to operate the M50 with the remote control.
Distance: About 23ft (7m) from the front of the remote sensor.
Angle: About 30° in each direction of the front of the remote sensor.
8 PLAY/PAUSE
• Toggle to start, pause or resume playback of current source.
9 MENU
• Display main menu options. Use the remote control's D/F buttons
to move up or down the menu selections. Press S to select a menu
item (use A to return to the main menu or previous display). Having
selected a menu item, use D/F buttons to select an option and
then press ENTER to confirm selection. Upon pressing ENTER, the
display will revert back to the main menu window.
•
The front panel 7/8/ 9/0 and ENTER buttons perform
respectively the same functions of the remote control A/S /F/D
and ENTER buttons. Use these buttons to navigate through the
MENU options.
}Info
Mass Storage Usage
Test Storage Usage
WiFi Hot Spot Mode
IR Channel
Reboot
Factory Reset
skip
scan scan
menu
skip
© NAD M50
9 10 11