Table of Contents
Advertisement
* Important: If a remote control button does not work when pressed, press the
remote and try the button again.
AUDIO OUTPUT
Select the digital output to be output from the
optical digital audio output connector of the unit.
1
Do steps 1 and 2 on page 60.
2
1) Press
DVD MAIN MENU
DISC LANGUAGES
AUDIO OUTPUT
ST I L L MODE
: F I ELD
2) Press SET to
TV MODE
: L e t t e r b o x
SELECT
:
SET
: SET
END
: ACTION
3
1) Press
AUDIO OUTPUT
LPCM(DVD)
: OFF
D o l b y D i g i t a l
: B i t s t r e a m
d t s
: OFF
2) Press SET
DRC
: OFF
SURROUND
: OFF
SELECT
:
SET
: SET
END
: ACTION
I I I I I "LPCM (DVD)" selections
OFF: Linear PCM of less than 48 kHz/16 bit is output.
When playing DVDs recorded in linear PCM of
over 48 kHz/20 bit or 96 kHz, no digital audio is
output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or 96 kHz, digital audio
converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
I I I I I "Dolby Digital" selections
Bitstream:
Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
OFF:
No output.
I I I I I "dts" selections
Bitstream:
dts bitstream is output. (Factory preset)
OFF:
No output.
I I I I I "DRC (Dynamic Range Compression)" selections
OFF: Normal audio range is selected. (Factory preset)
ON:
For dynamic sound even at low volume, this is
useful for late-night listening. [Dolby Digital DVDs
only].
I I I I I "SURROUND" selections
Surround Sound creates the effect of sound coming from
non-existent rear speakers even when only connected to
a 2-channel stereo system.
OFF: No Surround Sound effect. (Factory preset)
ON:
Surround Sound effect.
4
Press ACTION to redisplay DVD menu
and go to step 2 to setup another item.
Or, press ACTION three times to exit.
DM2092-K(P58-63 DVD).p65
Type of amplifier
to be connected
No amplifier is connected
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
to select
AV amplifier including
Dolby Digital decoder
"AUDIO OUTPUT."
AV amplifier including
Dolby Digital/dts decoder
display screen.
• Make settings according to amplifier
connected to optical audio output as shown in
above table.
to select
• When a dts decoder is not connected, to enjoy
an item.
dts DVD, please select audio output other than
dts on the dts DVD menu screen. Otherwise,
there will be no sound from the unit speakers.
repeatedly for output.
*1 Audio output from unit is converted to 48
(See below.)
kHz/16 bit in addition to audio from digital
audio output.
To enjoy high quality sound at 48 kHz/20 bit /
24 bit or 96 kHz, connect the amplifier or
decoder directly to the audio output
connectors, not to the digital audio output
connector. [Select "OFF" at the "LPCM
(DVD)".]
*2 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or dts decoder,
be sure to select "OFF".
If "Bitstream" is selected, starting DVD play
may cause such a high level of noise as to be
harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select "Bitstream" in "dts". If "OFF" is
selected, there will be no sound.
Notes
• Turn off other surround effects when
using this surround effect.
• For optimum effect, the distance between
the unit and the listener should be about
3 or 4 times the distance between the
right and left front speakers.
61
, DVD button on the
Recommended setting
LPCM
Dolby
dts
(DVD)
Digital
OFF
OFF
OFF
1
2
PCM*
OFF*
OFF*
1
PCM*
Bitstream
OFF
1
PCM*
Bitstream
Bitstream
61
2002/06/26, 9:49
2
3
*
Advertisement
Table of Contents
