Zetta Z15 Quick Start Manual

Zetta Z15 HD Security Camcorder Quick Start Guide
Overview
Congratulations on your purchase of Zetta Z15 HD security camcorder!
Zetta Z15 is an intelligent security camcorder with multi-function triggering and multi auto
on/off modes. The camcorder comes with a built-in rechargeable battery which can record
up to 10 hours continuous video and sound during typical use and standby for more than 4
months when vibration triggering is enabled. By plugging in the 5V DC adapter, it can achieve
168 hours circular recording.*
* Actual life and performance may vary depending upon usage and settings; battery not replaceable.
Features
Circular recording – loop back recording once memory card is full
Time stamp – put time stamp on video
Schedule recording – set the time to automatically turn on / off recording, 7-day circular
Vibration-trigger recording – select to record only when vibration is detected
Motion-trigger recording – select to record only when motion is detected
Voice-trigger recording – select to record only when voice is detected
Auto on/off mode – select different auto on/off scenarios
Selectable day/night mode – select day mode or night mode to suit your environment
Auto gapless split file – gaplessly split files for every 10 / 15 / 20 minutes
Orientation – use when the camcorder is turning up-side-down
Selectable resolution – recording of 1280x720(720p) or 640x360(360p) video and sound
Frame rate adjustment – lower the frame rate to save memory space
Configurable video quality – high / medium / low
Support max 64GB microSD(TF) card (for better performance, use card with class 4 or
above and before use, format the card as FAT32 only)

Package Contents

Please unpack your intelligent security camcorder and check that the following were included:
Zetta Z15 HD security camcorder
5V DC Adapter
USB 2.0 Cable
Quick Start Guide
Note: The configuration tool is not included in the package, please download it from
http://www.zetta.com.hk
Zetta Z15 at a Glance
LED indicator on/off
card slot
custom mode
surveillance mode On-the-GO mode
USB port
camera
microphone
www.zetta.com.hk
Charging
The camcorder comes with an internal rechargeable battery. To use the camcorder for
the first time or not using the camcorder for a long time, remember to fully charge the
battery for at least 6 hours and resync the time by using the Zetta Widget (see section
"Configuration Tool"). You can charge your camcorder through the USB port of your computer
or the DC adapter.
To charge the battery through USB port, connect the USB cable to the USB port of the
computer and the camcorder. For details, please see the status below. The camcorder will
function as a mass storage device, you will not be able to record video at this moment.
To charge the battery through DC adapter, connect the DC adapter to the camcorder. For
details, please see the status below. Moreover, you will also be able to record video while
charging, depending on the mode you set.
Recording
The power button is located at the right side of the camcorder. It can turn the camcorder on
or off.
Start Recording
Press and hold the Power button until the green LED is on (approximately 2 seconds), and
then release the button. When you see the green LED flashing, the camcorder is recording.
Otherwise, please see the status below.
Stop Recording
Press and hold the Power button until the orange LED is off (for approximately 2 seconds).
WARNING: Turn off camcorder before removing card!
Status
Without DC adapter
Green LED on: camcorder is booted up
Green LED flashing: normal recording
Green / Red LED intermittent flashing: battery low and recording
Red LED on: no card, card fail, battery low or card full (not in circular recording)
DC adapter plugged in
Orange LED on: charging but no recording
Green LED on: charging complete but no recording
Green LED flashing: charging complete and recording
Green / Orange LED intermittent flashing: charging and recording
Red LED on: no card, card fail or card full (not in circular recording)
Connected to computer
Orange LED on: charging
Green LED on: charging complete