Chapter 3 AMI BIOS Setup ..................24 Overview ....................24 Main Menu ....................25 Advanced Menu ..................26 Boot Menu ....................34 Security Menu .................... 35 Save & Exit Menu ..................35 Chapter 4 Driver Installation .................. 37 QBOX-200S User’s Manual...
The product chassis may be hot when the system is working. Please do not touch the surface before turn off the system power and wait for about 5 minutes until the system cools down. QBOX-200S User’s Manual...
Also, before connecting a cable, make sure both connectors are correctly oriented and aligned. CAUTION Do not attempt to service the system yourself except as explained in this user’s guide. Follow installation and troubleshooting instructions closely. QBOX-200S User’s Manual...
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. QBOX-200S User’s Manual...
Do not dispose of lithium batteries in domestic waste. Dispose of the battery according to the local regulations dealing with the disposal of these special materials (e.g. to the collecting points for disposal of batteries) QBOX-200S User’s Manual...
(take adequate measures) at their own expense. The user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. QBOX-200S User’s Manual...
Buildings in which climate is controlled usually maintain an acceptable level of humidity for system equipment. However, if a system is located in an unusually QBOX-200S User’s Manual...
Page 11
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety approved. QBOX-200S User’s Manual...
Introduction Overview The QBOX-200S is a fanless digital signage player ideal for space critical applications. This embedded hardware platform features Intel® BayTrail Processor, Atom™ E3825, and DDR3L SO-DIMM. It comes with 1x HDMI, 1x VGA, 2x USB2.0, 1x USB 3.0, 1x GbE LAN, 1x mSATA, 1x Micro SD card cage, 1x COM.
ATX/AT Mode Support Operating: 0°C to 45°C Temperature Storage: -20°C to 80°C Humidity Humidity: 0% to 90% Dimensions 150.6 x 80.8 x 33mm ( W x D x H ) Certifications CE, FCC Class A Table 1 QBOX-200S Specification QBOX-200S User’s Manual...
The hard disk LED blinks when data is being written into or read from the HDD. Phone Jack Audio Out The green stereo headphone jack is used to connect the system’s audio out signal to amplified speakers or headphones. QBOX-200S User’s Manual...
Page 15
The USB (Universal Serial Bus) port is compatible with USB devices such as keyboards, mouse devices, cameras, and hard disk drives. USB allows many devices to run simultaneously on a single computer, with some peripheral acting as additional plug-in sites or hubs. QBOX-200S User’s Manual...
The eight-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network. HDMI HDMI connector for display output D-Sub 15 pin VGA connector for display output Antenna reserved holes for wireless antenna connections. QBOX-200S User’s Manual...
HDMI Figure 4 VGA/ HDMI NOTE When the system reboots without connecting the VGA/HDMI, there might be no image on screen when you insert the VGA/HDMI cable. Please pressing <Ctrl>+<Alt>+<F4> simultaneously to show the image on screen. QBOX-200S User’s Manual...
Chapter 2 Connect USB mouse & keyboard Your QBOX-200S does not come with a keyboard and mouse connector, but you can use any USB keyboard or mouse to connect with your computer. USB 3.0 Figure 5 Connect USB mouse & keyboard NOTE Using a third-party USB mouse or keyboard may require software drivers.
Chapter 2 Connect LAN port Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch. RJ45 Figure 6 RJ45 connector QBOX-200S User’s Manual...
Connect the power cable to the power adapter Connect the power cable to a power outlet Press the power switch on the front panel to turn on the system DC Jack Power Switch Figure 8 Turning on the system QBOX-200S User’s Manual...
Figure 9 VESA mounting (1) NOTE To fasten the metal shelf, your monitor must comply with VESA75 or VESA100 standard. Place the QBOX-200S onto the monitor and secure it with the four screws properly on both sides of VESA mount kit as shown below.
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS only. If this happens you will need to reconfigure your BIOS settings. QBOX-200S User’s Manual...
Menu provides System Overview information and allows you to set the System Time and Date. Use the “<” and “>” cursor keys to navigate between menu screens. Table 2 QBOX-200S BIOS Main Menu BIOS SETUP UTILITY M a i n...
Port 1 Empty F4 Save & Exit Port 1 [ Enabled ] ESC Exit Version 2.16.1242. Copyright (C) 2013, American Megatrends, Inc. SATA Options: Disabled, Enabled SATA Mode Options: IDE Mode, AHCI Mode Port 1 Options: Disabled, Enabled QBOX-200S User’s Manual...
[ Disabled ] +- Change Opt. F1: General Help Current Status Information F2: Previous Values F3: Optimized Defaults F4 Save & Exit ESC Exit Version 2.16.1242. Copyright (C) 2013, American Megatrends, Inc. Security Device Support Options: Disabled, Enabled QBOX-200S User’s Manual...
F1: General Help +VCORE : +0.789 V F2: Previous Values +VIN : +11.644 V F3: Optimized Defaults : +5.106 V F4 Save & Exit +VMEN : +1.349 V ESC Exit Version 2.16.1242. Copyright (C) 2013, American Megatrends, Inc. QBOX-200S User’s Manual...
Options: Power Off, Power On, Last State Resume By PCIE Device Options: Disabled, Enabled Resume By RTC Alarm Options: Disabled, Enabled EUP Power Saving Mode Options: Disabled, Enabled Watchdog Timer Configuration WDT Function [Disabled] ■ Options: Disabled, Enabled QBOX-200S User’s Manual...
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. Full Screen LOGO Display Options: Disabled, Enabled Bootup Numlock State Options: On, Off Keyboard Detect Warning Options: Disabled, Enabled CSM Support Options: Disabled, Enabled Boot Option Filter Options: UEFI and Legacy, Legacy only, UEFI only QBOX-200S User’s Manual...
Discard Changes and Reset Enter: Select Save Options +- Change Opt. Save Changes F1: General Help Discard Changes F2: Previous Values F3: Optimized Defaults Restore Defaults F4 Save & Exit ESC Exit Version 2.16.1242. Copyright (C) 2013, American Megatrends, Inc. QBOX-200S User’s Manual...
Page 36
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. QBOX-200S User’s Manual...