Table of Contents
Advertisement
H
o
r
s
e
F
l
a
m
e
®
H
o
r
s
e
F
l
a
m
e
®
W
o
o
d
&
M
u
l
t
i
-
F
u
e
l
S
t
o
v
e
s
W
o
o
d
&
M
u
l
t
i
-
F
u
e
l
S
t
o
v
e
s
Introduction
Congratulations on purchasing a genuine Horse Flame® Stove. When cared for properly,
these high quality, finely crafted cast iron stoves and fireplaces will offer many years of
reliable performance. This instruction manual has been developed to ensure optimum per-
formance from the Horse Flame® stove and fireplace range. It's very important that you tho-
roughly read and understand all instructions before using your new stove or fireplace.
Check Building Codes
When installing, operating and maintaining your stove, follow the guidelines presented in
these instructions, and make them available to anyone using or servicing the stove. Your
city, town, county or province may require a building permit to install a solid fuel burning
appliance.
Always consult your local building inspector or authority having jurisdiction to determine what
regulations apply in your area.
Kindly save these instructions for future references
~ 1 ~
Advertisement
Table of Contents
Related Manuals for Horse Flame HF-317
Summary of Contents for Horse Flame HF-317
-
Page 1: Check Building Codes
This instruction manual has been developed to ensure optimum per- formance from the Horse Flame® stove and fireplace range. It's very important that you tho- roughly read and understand all instructions before using your new stove or fireplace. -
Page 2: Stove Safety
Stove Safety When properly maintained and operated your stove should give you many years of service, however there are important safety aspects of these products that you need to be aware of when operating a stove. 1. The term Multi-fuel refers to any of the main commercially available solid fuels such as coal, wood, turf, anthracite, briquettes. -
Page 3: Before Installing Your Stove
Before installing your stove You need to consider the following to ensure the safe operation of your stove. • Provision of adequate air to support efficient combustion of the fuel. • A well sealed flue/chimney system, hereinafter referred to as the “flue system”. •... -
Page 4: Installation
Installation Unpacking and preparing your stove for installation. 1. Remove your stove from the outer packaging and place on floor. Please inspect stove and check that it is not damaged in any way. Never attempt to use a stove that has been damaged. - Page 5 Parallel Installation Corner Installation Single wall Double wall connector pipe connector pipe A – Chimney Connector to backwall 16.5” (419 mm) 10.5” (267 mm) B – Chimney Connector to sidewall 22” (559 mm) 18” (457 mm) C – Chimney Connector to cornerwall 20”...
- Page 6 Some typical installations are shown as following Sealed door to FLUE access chim- ney for sweep- ing & inspect- ing. The Flue must be 1.5mm thick rust resistant steel and 3 times it‘s Non-combustible reg- diameter away from combust- ister plate. Minimum ible materials.
- Page 7 For Installations where no Chimney exists The Connecting flue pipe from the Stove should connect to the Twin Wall Insulated flue pipe, ensure this flue pipe is the correct type for Multi-Fuel applications. Some typical installations are shown as following: Support Collar Fire Stop Spacer 45°...
- Page 8 The Chimney/Terminal Outlet must be no lower than the minimum positions shown in the diagram below: Point where flue passes through weather Clearance to flue outlet surface (Notes 1,2) At or within 500mm of the ridge. At least 600mm above the ridge. At least 2300mm horizontally from the nearest Elsewhere on a roof point on the weather surface and:...
-
Page 9: Operating Your Stove
Operating Your Stove Fuel Your stove is designed to burn a range of solid fuels such as coal, wood, turf (peat) and etc.; it is not designed to burn, • Paper or cardboard, other than small amounts used to light stove. •... -
Page 10: Ash Removal
tablished, the controls may be adjusted as required. Reducing the air intake will cause the stove to burn slower. This may cause some blackening of the stove glass, but this should burn off once the stove is burning brightly again. Refueling Before refueling your stove, turn the air supply to high for a few moments until there is a good fire in the stove. -
Page 11: Stove Maintenance
Care of glass At times, especially when the air controls are turned to low settings or when damp wood is used, the stove glass will blacken. This is caused by fuel that is not completely burnt, but the build-up on the inside of the glass will normally burn off when a good hot fire is established in the stove. -
Page 12: Troubleshooting
2. Check that glass is not cracked or chipped and that sealing rope is in good condition. Replace as necessary. 3. When the room is dark, use a strong flashlight to check the sealing of the stove at the edge and corners for leaks. Any leaks or cracks found should be repaired with fire cement or damaged parts should be replaced with genuine spare parts. -
Page 13: Glass Blackens
Glass blackens Glass usually blackens when: The fuel is not being burned efficiently because of starvation of air. Bad quality or damp fuel is being used. Balance between primary and secondary air is incorrect. Try to introduce more air into the stove, especially through the secondary air control on the top of the stove door as this air flows down over the glass to help burn off the creo- sote. -
Page 14: Additional Info
ADDITIONAL INFO (FOR BOILER MODEL ONLY) Boiler Connection The advanced Back-Boiler fitted in your Stove must be installed in Compliance with all re- levant Building Regulations and in accordance with Central Heating Standard EN 12828 whilst complying with local Water Supply Regulations. Guidance and further information is available from your Local Water Supplier. - Page 15 The thermostat is a safety device. It automatically closes the air inlet when the water temperature is more than 85± 3℃, so that the water doesn’t get too hot. And it automati- cally opens the air inlet to the set open position when the water temperature is lower than 80±...
-
Page 16: Technical Data
This low level thermostat prevents the system pump for running un- til the stove has reached temperature. TECHNICAL DATA Overall Size (mm) Flue Size Model Output Efficiency Weight H x W x D (mm) (Kg) HF-317 Artemis 660mmX526mmX438mm 125mm (5”) 87kg HFB-317 Windsor 660mmX526mmX438mm 125mm (5”) 96kg HF-517 Baldemar 11kw 715mmX556mmX518mm 150mm (6”) -
Page 17: Horse Flame Warranty
The warranty does not cover parts deemed to be consumables. These include paint, fire- bricks, vermiculite panels, smoke deflection plates(baffle plates), gaskets, rope seals and glass. Horse Flame will repair or replace at its option any stove or stove part thereof found to be defective under these terms. 17 ~... - Page 18 (other than those by the authorised dealer) or failure to maintain the stove in a serviceable condition. Under no circumstances shall Horse Flame be liable for any incidental or consequential damage claims of any nature whatsoever arising from the non-conformance of the stove under the terms of the manufacturer’s warranty.