Remote Control - Arcam AVR250 Handbook

Remote control

The CR80 remote control is a multi-function unit that controls the
AVR250 and up to seven other devices. The instructions on this page
only refer to the control of the Arcam AVR250.
For information on using the remote control for other devices, and
a full list of features, see the instruction booklet supplied with the
CR80.
Source selection
– DVD input
DVD
– Satellite input
SAT
– toggle between the VCR and PVR inputs
VCR
– CD player input
CD
– Tape (monitor) input
TAPE
– AV input
AV
– DVD-A (multi-channel) input
MCH
– FM tuner input
FM
– AM tuner input
AM
Press the relevant button once to select input;
press and hold to select the analogue input if a
digital input is present.
MUTE
Press once to mute the main system. Press again
(or use ) to un-mute.
VOL +/–
VOLUME +/–
Adjusts the volume.
MODE
Use this button to cycle through available
surround modes.
INFO
Press to change the RDS display mode for the
tuner.
P- / P+ (Tune/Preset Down/Up)
If the tuner is in mode, then these
PRESET
buttons decrease/increase the preset selection.
If the tuner is in mode, then these buttons
TUNE
decrease/increase the selected frequency.
SYN (Lip sync)
Press once to adjust the Lip sync audio delay. Use
3 4
the and navigation buttons.
Press again to exit the Lip sync function.
DIS (Display)
Press to cycle through Off/Dim/Bright illumination
of the front panel display
TRM (Speaker trim)
Press to display the OSD Speaker trim level
menu.
speaker levels, using the navigation buttons.
Press again to exit the 'Speaker Trim' function.
AVR250
E-18
allows temporary adjustment of
TRM
Device selection
IMPORTANT: Press the 'AMP' button first to operate
the AVR250.
SET
SELECT DEVICE
CBL DVD VCR TV
SAT CD AMP AUX
1 2 3
DVD SAT VCR
4 5 6
CD AUX TAPE
7 8 9
TUN AV MCH
0
MUTE
FM AM
LAST
THX
SLEEP
VOL CH
FX
A–B
SUB
EXIT
GUIDE
OPEN
MODE
OK
INFO MENU
P.MODE SUBT TITLE MENU
P – P + TM FAV
ZOOM AUDIO MEM RETURN
TST SYN DYN SLP
ANGLE SETUP STATUS SEARCH
DIS TRM 1 2
CR80
NOTE
Remember to install the two AA batteries supplied before
trying to use your remote control.
On/Stand-by
This allows the AVR250 to be put into and
taken out of stand-by remotely.
THX
In Zone 2, use this button to enable 'Follow
Zone 1' mode.
Note that the AVR250 does not support THX
processing.
FX (DSP effects mode)
Use this button to cycle through effects
modes for two-channel sources.
SUB (Subwoofer trim)
Allows a temporary trim of the subwoofer
level. Press , then adjust using
SUB
34
the buttons on the navigation panel.
Navigation buttons
Arrow buttons allow navigation around the
menus on the AVR250.
Confirm selection by pressing
MENU
Press to select the OSD Main menu.
Press and hold for more than two seconds to
select the 'Set-up Menu Index'.
TM
Tuning mode: press this button to toggle
between 'preset' and 'tuning' modes on the
tuner.
DYN/MEM
Used to store a radio station in a preset.
Press once to enter store mode; use the
/ buttons to select the preset to use,
P+ P-
then press this button again to confirm the
selection.
1/STATUS
Press this button to toggle between FM
'stereo mute' and 'mono' on the tuner.
The other buttons in this area are used for
DVD control and do not effect the AVR250.
.
OK