Model C1060 Table of Contents Safety Information .......................... iii Intended Use .............................iii FCC Information..........................iv System Description .......................... 1 Introduction...............................1 System Configurations..........................1 Single–Lane Standard Communication System .................1 Single–Lane Duplex Communication System..................1 Dual–Lane Standard Communication System..................1 Dual–Lane Duplex Communication System ..................1 Cross–Lane Communication System ....................1...
Page 4
Charging Batteries..........................15 Disposing of Batteries ........................16 Making Sure Batteries are Ready for Use..................16 Important Information about C1060 Rechargeable Batteries ............16 Special Instructions for System Manager ..................17 Programming the Headset for Cross–Lane Operation................17 Reprogramming ..........................17 Enabling/Disabling the Talk Lock Feature....................
Read, understand, and follow all safety information contained in these instructions prior to installation & operation of the 3M Headset Intercom System, Model C1060. Failure to follow all instructions listed could result in electrical shock, fire and/or other personal injury. Retain these instructions for future reference.
For communications equipment sales and service, contact your local 3M authorized intercom dealer. If special service assistance is needed, or for information on how to properly dispose of your non–functional C1060 rechargeable batteries, please call (800) 328-0033. For more information, visit the 3M Foodservice Web site: http://www.3m.com/foodservice...
Model C1060 System Description Introduction The 3M Model C1060 Headset Intercom System is a wireless intercom system designed for high reliability, compactness, and ease of service. The system can be programmed to operate on any one of 16 different channels to provide high–quality audio performance and reduce the possibility of...
System Description Model C1060 Systems The number of system components and the procedures necessary to operate them vary depending on the system configuration. However, four components Components are common to all system configurations. The base station is the interface between the customer at the menu sign and the Base Station headset worn by the operator.
The programming station is used to program C960 and C1060 headsets to the same channel as the base station. Infrared light is used to transfer program data to the C1060 headset and a separate jack is provided for the C960 headset programming cable. See Figure 3.
This indicator lights when the ON/OFF switch is in the ON position. 2 POWER Indicator Note If for some reason the C1060 headset system does not operate and the system includes an optional wired backup system, turn off the C1060 Base Station to enable the backup system. 3 VOLUME With the switch in the DAY position, the volume of the menu sign speaker is increased for daytime operation.
Model C1060 Controls and Indicators Headset The headset controls are shown below. Figure 6. Headset Controls 1 ON / OFF Switch Press the switch once to turn on the headset, and press it again (when the headset is on) to turn off the headset Press the volume up control to increase the volume in the headset earpiece.
Page 12
Controls and Indicators Model C1060 5 T2 (Talk Lane 2) For dual–lane systems, press and hold the T2 (Talk Lane 2) switch to talk to the customer at the menu sign in lane 2. Release the switch to listen. Switch For single–lane systems, T2 can also be used to talk to lane 1.
Model C1060 Controls and Indicators Battery Chargers The 3–slot and 6–slot battery charger controls are shown below. Figure 7. Battery Chargers The charging slots hold batteries during the recharging cycle. 1 Charging Slots 2 Charging Status The charging status indicators light RED or GREEN to indicate charging status: Indicators RED indicates the battery is being charged.
Headset Preparation Model C1060 Headset Preparation Rotate ear cup and ear pad so that the indicator on the ear cup is aligned to the 1. Rotate Ear Cup back of your head. This sets the angle of the ear pad for a comfortable fit.
Model C1060 Operation System startup includes turning on the base station and each headset that will be System Startup used. To turn on the base station: Turning On the Base Station 1. Slide the power ON/OFF switch to the ON position. Check to see that the POWER indicator lights.
Operation Model C1060 Communication During Off–Peak Hours During off–peak hours, the cross–lane module is turned on to enable a single operator to communicate with customers in either lane (1 or 2). 1. An alert tone sounds in the headset when the system detects a customer (vehicle) at the menu sign: •...
Model C1060 Operation Use this mode to talk to other operators who are wearing headsets without being Page Mode heard by the customer at the menu sign. This mode is available with all system configurations. To page another operator, press and hold the page switch. Release the page switch to listen.
Operation Model C1060 LED Indicator Turns green?? . . . then press ON / OFF Switch Press and hold PAGE switch . . . Figure 11. Page Switch and On / OFF Switch To respond to a page, press P (page switch).
When installing a battery, make sure it is fully charged. It is important to remember that an unused C1060 battery loses five percent of its charge per week. If a battery has not been used for several weeks, make sure to charge prior to use.
Maintenance Model C1060 Replacing the Ear To replace the ear pad, remove the worn/damaged ear pad from the ear cup and and Headband Pads replace it with a new pad. See Figure 13. Figure 13. To replace the headband pad, remove the worn/damaged pad by peeling it from the back of the battery housing.
Model C1060 Maintenance Battery Charger Location The battery charger should be placed on a flat surface such as a desktop or table in a clean, dry environment. Cleaning the Contacts If the indicators fail to light during charger operation, clean the contacts using a water–moistened cotton swab.
Batteries perform best at moderate temperatures. Extremes of heat and cold reduce their performance. • An unused C1060 battery loses five percent of its charge per week. Batteries that have not been used for several weeks should be recharged before use.
Model C1060 Special Instructions for System Manager Programming the The headsets are factory programmed for single–lane operation to enable the operator to press either T1 or T2 to communicate with lane 1. Headset for Cross- Lane Operation For cross–lane systems, the headsets must also be programmed to enable communication with either lane 1 or lane 2.
In cases where a cellular phone tower is nearby, certain combinations of cell frequencies may cause random interference. In some cases, changing channels may have no effect. Please call your local 3M Dealer, or 3M F.S.T. Communications Products Technical Service (800–328-0033) in these cases.
Page 25
Model C1060 Special Instructions for System Manager The C1060 system is capable of operating on any one of eight different channels. You can correct these types of interference by changing the base station operating channel. To do this: 1. With the base station turned on, press and release the Channel Select switch once.
Page 26
Special Instructions for System Manager Model C1060 Important Note: Align the missing pin in the programming station jack with the plugged position in the end of the programming cable. Figure 18. 3. Press the RESET switch to “read” the new channel selection into the microprocessor.
Model C1060 Special Instructions for System Manager Figure 19. 4. With the headset turned OFF, swing the microphone back, and insert the headset into the programming station with its programming window facing toward the programming cable jacks. See Figure 19.
Special Instructions for System Manager Model C1060 Day/Night Monitor Switch Volume Access Figure 20. Normally, the VOLUME DAY/NIGHT switch is always left in the DAY position. However, if local ordinances require quieter nighttime operation of the menu sign, move the VOLUME DAY/NIGHT switch to the NIGHT position.
Page 31
2. Turn the backup intercom on or backup wired intercom. The intercom. plug in its power transformer. C1060 system works OK. 3. The volume controls are set too 3. Turn the volume controls up. low on the backup intercom. 4. Defective backup intercom or 4.
For communications equipment sales and service, contact your local 3M Service authorized intercom dealer. If special service assistance is needed, or for information on how to properly dispose of your non–functional C1060 rechargeable batteries, please call (800) 328-0033. For more information, visit the 3M Foodservice Web site: http://www.3m.com/foodservice...