Table of Contents
Advertisement
SPECIFICATIONS
FM
T uning Range:
87.90 - 107.90 MHz, 200 kHz steps
(U.S. & Canadian models)
87.50 - 108.00 MHz, 50 kHz steps
(Ohter area models)
Usable Sensitivity:
Mono : 12.8 dBf 1.2 µV , 75 Ohms IHF
Stereo: 19.2 dBf 2.5 µV , 75 Ohms IHF
50dB Quieting Sensitivity:
Mono : 18.0 dBf 2.2 µV , 75 Ohms
Stereo: 38.0 dBf 22 µV , 75 Ohms
Capture Ratio : 1.5 dB
Image Rejection Ratio : 85 dB
IF Rejection Ratio : 90 dB
Signal-to-Noise Ratio :Mono: 73 dB IHF
Stereo: 66 dB IHF
Selectivity : 50 dB DIN (±300 kHz, 40 kHz dev .)
AM Suppression Ratio : 50 dB
T otal Har monic Distortion : Mono: 0.5%
Stereo: 0.8%
Frequency Response : 30 - 15,000 Hz (±1.5 dB)
Stereo Separation :40 dB at 1 kHz
30 dB at 70 - D 10,000 Hz
Output Level : 0.5 V (U.S.& Canadian models)
0.75 V (Other ar ea models)
Muting Level : 17.2 dBf 2.0 µV, 75 Ohms
SERVICE PROCEDURES
1. Replacing the fuse
This symbol located near the fuses indicates that the
fuse used is fast operating type. For continued protection against
fire hazard, replace with same type fuse. For fuse rating refer to
the marking adjacent to the symbol.
Ce symbole indique que le fusible utlise est a rapide.
Pour une protection permanente, n'untiliser que fusibles de
meme type. Ce darnier est la qu le present symbol est
appse.
CIRCUIT NO.
PART NO.
252075
F901
2. To initialize the unit
This device employs a microprocessor to perform various
functions and operations. If interference generated by an external
power supply, radio wave, or other electrical source results in
accident which causes the specified operations and functions to
operate abnormally.
To perform a result, please follow the procedure below.
1.Set the unit to the standby mode
2.Press and hold down the MEMORY button, then press the
DISPLAY button.
3.The segments of the F.L.tube light on and the unit is set to the
test mode.
4.'Clear' is displayed when the power switch is pressed in the
state of the test mode and the memory is cleared.
AM
T uning Range :
530 - 1,710 kHz, 10 kHz steps
Usable Sensitivity : 30 µV
Image Rejection Ratio : 30 dB
IF Rejection Ratio : 40 dB
Signal-to-Noise Ratio : 40 dB
T otal Harmonic Distortion : 0.8%
Output Level: 0.15 V
General
Power Supply :
AC 120 V , 60 Hz
AC 230-240 V , 50 Hz
Power Consumption : 9 W
Dimensions (W x H x D) :
205 x 76 x 279 mm
8-1/16" x 3" x 11"
Weight : 1.7 kg, 3.7 lbs.
AM reception is available only on the U.S. and Canadian
models.
Specif i cations and exter n al appearance are subject to
change without notice as a result of product improvement.
DESCRIPTION
2.5A-SE-EAK,Fuse
T-405TX
Advertisement
Table of Contents
