Download Print this page

Advertisement

Alarm Clock Radio
AM/FM/CD
I'll Wake You Up in Style
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
DANGER: This symbol is intended to alert the user to the risk of exposure to invisible and hazardous laser radiation if the cover
or back is opened the interlock fails or is defeated. Direct exposure to the beam may damage your eyesight.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The rating information is located at the rear of the apparatus.
LASER SAFETY: This unit employs a laser. Only qualified service personnel should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADjUSTMENTS OR PERFORMANCE PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION ExPOSURE.
SURGE PROTECTORS: It is recommended to use a surge protector for AC connection. Lightning and power surges ARE NOT covered under warranty for
this product.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these Instructions.
manufacturer, or sold with the apparatus. When a
2. Keep these Instructions.
cart is used, use caution when moving the cart/
3. Heed all Warnings.
apparatus combination to avoid injury from tip-over.
4. Follow all Instructions.
13. Unplug this apparatus during lightning storms or
5. Do not use this apparatus near water.
when unused for long periods of time.
6. Clean only with a dry cloth.
14. Refer all servicing to qualified service personnel.
7. Do not block any of the ventilation openings. Install in accordance with
Servicing is required when the apparatus has
the manufacturer's instructions.
been damaged in any way, such as power-supply
8. Do not install near any heat sources such as radiators, heat registers,
cord or plug is damaged, liquid has been spilled or objects have fallen
stoves, or other apparatus (including amplifiers) that produce heat.
into the apparatus, the apparatus has been exposed to rain or moisture,
9. Do not defeat the safety purpose of the polarized or grounding-type
does not operate normally, or has been dropped.
plug. A polarized plug has two blades with one wider than the other.
15. WARNING: To reduce the risk of fire or electric shock, do not expose this
A grounding-type plug has two blades and a third grounding prong.
apparatus to rain or moisture. Do not place objects filled with water, such
The wide blade or the third prong are provided for your safety. When
as a vase, on the apparatus.
the provided plug does not fit into your outlet, consult an electrician for
16. The AC mains plug is used as the power disconnect device and it should
replacement of the obsolete outlet.
remain readily accessible and operable during intended use. In order to
10. Protect the power cord from being walked on or pinched particularly at
completely disconnect the apparatus from power, the mains plug should
plugs, convenience receptacles, and the point where they exit from the
be completely removed from the AC outlet socket.
apparatus.
17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries
11. Only use attachments/accessories specified by the manufacturer.
to excessive heat such as sunshine, fire or other heat sources.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
PRECAUCIóN
RIESGO DE DESCARGA ELÉCTRICA
NO ABRIR
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA, NO QUITE LA CUBIERTA (NI LA PARTE TRASERA). NO CONTIENE PIEZAS EN EL
INTERIOR QUE PUEDAN SER REPARADAS POR EL USUARIO. EL MANTENIMIENTO DEBE SER REALIZADO POR PERSONAL DE MANTENIMIENTO CALIFICADO.
VOLTAJE PELIGROSO: El rayo con el símbolo de la punta de flecha dentro de un triángulo equilátero tiene como objetivo advertir al
usuario acerca de la presencia de voltaje no aislado peligroso dentro de la caja del producto que puede ser de magnitud suficiente
para generar un riesgo de descarga eléctrica para las personas.
ATENCIÓN: El signo de exclamación dentro de un triángulo equilátero tiene como objetivo alertar al usuario acerca de la presencia de
instrucciones de funcionamiento y mantenimiento (servicio) importantes en la bibliografía que acompaña a la aplicación.
PELIGRO: Cuando se abre o rompe el seguro, existe la posibilidad de exposición a radiación peligrosa. Evite exponerse a dicho rayo.
ADVERTENCIA DE LA FCC: ESTE EQUIPO PUEDE GENERAR O UTILIZAR ENERGíA DE RADIO FRECUENCIA. LOS CAMBIOS O LAS MODIFICACIONES DE
ESTE EQUIPO PUEDEN PROVOCAR INTERFERENCIA PERjUDICIAL, A MENOS QUE ESTÉN ExPRESAMENTE APROBADAS EN EL MANUAL DE INSTRUCCIONES.
EL USUARIO PODRíA PERDER LA AUTORIDAD PARA HACER FUNCIONAR ESTE EQUIPO SI REALIZA ALGúN CAMBIO O MODIFICACIóN NO AUTORIZADOS.
PRECAUCIÓN: PARA EVITAR DESCARGAS ELÉCTRICAS, UNA LA CLAVIjA ANCHA DEL ENCHUFE CON LA RANURA ANCHA E INSÉRTELA POR COMPLETO.
ESTE DISPOSITIVO CUMPLE CON LA PARTE 15 DE LAS REGLAS DE LA FCC (FEDERAL COMUNICATIONS COMMISSION). EL FUNCIONAMIENTO DEPENDE DE
LAS DOS CONDICIONES QUE SE MENCIONAN A CONTINUACIóN: (1) ESTE DISPOSITIVO NO CAUSA INTERFERENCIA NOCIVA Y (2) ESTE DISPOSITIVO DEBE
ACEPTAR TODA INTERFERENCIA RECIBIDA, INCLUYENDO INTERFERENCIA QUE PUEDA OCASIONAR UN FUNCIONAMIENTO INDESEABLE.
NOTA: Este equipo ha sido probado y cumple con los límites correspondientes a un dispositivo digital Clase B, según la parte 15 de las Normas de FCC.
Estos límites están diseñados para proporcionar una protección razonable contra la interferencia dañina en una instalación residencial. Este equipo genera,
utiliza y puede irradiar energía de radiofrecuencia y, si no se instala y usa de acuerdo con las instrucciones, puede generar interferencia perjudicial en
las comunicaciones de radio. Sin embargo, no se garantiza que la interferencia no se produzca en una instalación en particular. Si este equipo genera
interferencia perjudicial en la recepción de radio o televisión, que puede determinarse encendiendo y apagando el equipo, se recomienda al usuario que
intente corregir la interferencia mediante una o más de las siguientes medidas:
• Vuelva a orientar o ubicar la antena receptora.
• Aumente la separación entre el equipo y el receptor.
• Conecte el equipo a un tomacorriente de un circuito distinto del que está conectado el receptor.
• Consulte con el distribuidor o con un técnico de radio o TV experimentado para obtener asistencia.
• La información de clasificación se encuentra en la parte posterior del aparato.
PRODUCT
Alarm Clock Radio – QSG/Userguide (FRONT)
ART NUMBER
73952890
MODEL NUMBER
MC7223
LOCATION
Troy Larson - 651 704 3014
MEDIDAS DE SEGURIDAD CON EL RAYO LÁSER: Esta unidad usa un rayo láser. Sólo el personal calificado deberá dar servicio a este dispositivo a fin
de evitar daños a los ojos.
ADVERTENCIA: EL USO DE LOS CONTROLES, O EL PROCEDIMIENTO DE FUNCIONAMIENTO QUE NO SEAN LOS ESPECIFICADOS AQUí, PUEDEN DAR
COMO RESULTADO UNA ExPOSICIóN A RADIACIóN PELIGROSA.
PROTECTORES CONTRA SOBRETENSIÓN: SE RECOMIENDA UTILIZAR UN PROTECTOR CONTRA SOBRETENSIóN PARA LA CONExIóN DE CA. LOS CASOS
DE SOBRETENSIóN DE ENERGíA Y RAYOS NO ESTÁN CUBIERTOS POR LA GARANTíA DE ESTE PRODUCTO.
ADVERTENCIA: PARA EVITAR EL RIESGO DE INCENDIO O DESCARGA, NO EXPONGA ESTA UNIDAD A LA LLUVIA O LA HUMEDAD.
Este aparato digital Clase B cumple con la norma canadiense ICES-003.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
1. Lea estas instrucciones.
carro, tenga cuidado al mover la combinación de
2. Conserve estas instrucciones.
carro y aparato para evitar lesiones por caídas.
3. Preste atención a todas las advertencias.
13. Desconecte el aparato durante las tormentas
4. Siga todas las instrucciones.
eléctricas o cuando no se utilice durante un
5. No utilice este aparato cerca de agua.
período prolongado.
6. Limpie sólo con un paño seco.
14. El mantenimiento debe ser llevado a cabo
7. No bloquee ninguna de las aberturas de ventilación. Instale el producto
por personal de mantenimiento calificado. Se
de acuerdo con las instrucciones del fabricante.
requiere mantenimiento si el aparato se dañó
8. No instale el producto cerca de fuentes de calor, como radiadores,
de alguna forma; por ejemplo, si se derramó líquido o cayeron objetos
rejillas de calefacción, estufas u otros aparatos (incluidos los
dentro del aparato, si se expuso a la lluvia o a la humedad, si se cayó,
amplificadores) que generen calor.
si no funciona normalmente o si se dañó el cable de alimentación o el
9. No rechace el objetivo de seguridad del enchufe polarizado o de
enchufe.
conexión a tierra. Un enchufe polarizado tiene dos clavijas: una más
15. ADVERTENCIA: Para reducir el riesgo de incendio o descarga eléctrica,
ancha que la otra. Un enchufe de conexión a tierra posee dos clavijas
no exponga este aparato a la lluvia o a la humedad. No coloque objetos
y una tercera prolongación de conexión a tierra. La clavija ancha y
con líquidos (p. ej., jarrones) sobre el aparato.
la tercera clavija se proporcionan para su seguridad. Si el enchufe
16. El cable de alimentación de CA es el dispositivo para desconectar la
proporcionado no encaja en su tomacorriente, comuníquese con un
corriente; por lo tanto, debe estar al alcance de la mano y se debe
electricista para reemplazar el tomacorriente obsoleto.
poder manejar durante el uso previsto. Para desconectar el aparato de
10. Proteja el cable de alimentación de pisadas o pinchaduras, en particular
la corriente, el cable de alimentación se debe quitar completamente del
en los enchufes, los tomacorrientes y el punto de donde salen del
tomacorriente de CA.
aparato.
17. PRECAUCIóN: Para reducir el riesgo de incendio o explosión, no
11. Utilice sólo dispositivos/accesorios especificados por el fabricante.
exponga las pilas a calor excesivo, como la luz solar directa, el fuego u
12. Use sólo el carro, el pie, el trípode, el soporte o la mesa especificados
otras fuentes de calor.
por el fabricante o que se vendan con el aparato. Cuando se utilice un
MISE EN GARDE
RISQUE DE CHOC ÉLECTRIQUE NE
PAS OUVRIR
MISE EN GARDE : POUR RÉDUIRE LES RISQUES DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE COUVERCLE (OU L'ARRIÈRE). AUCUNE PIÈCE À L'INTÉRIEUR
NE PEUT ÊTRE RÉPARÉE PAR L'UTILISATEUR. CONFIEZ TOUTE RÉPARATION À UN TECHNICIEN QUALIFIÉ.
TENSION DANGEREUSE : L'éclair avec le symbole de la pointe de flèche dans un triangle équilatéral est destiné à alerter l'utilisateur
de la présence de tension dangereuse non isolée dans le boîtier du produit. Elle peut être suffisamment importante pour constituer un
risque de décharge électrique pour les personnes à proximité.
ATTENTION : Le point d'exclamation dans un triangle équilatéral est destiné à alerter l'utilisateur de la nécessité de respecter les
consignes d'utilisation et de maintenance (réparation) fournies dans la documentation qui accompagne l'appareil.
DANGER : Rayonnement invisible et dangereux émis lorsque le compartiment à disque est ouvert, mal verrouillé ou endommagé.
Évitez toute exposition directe au faisceau lumineux.
AVERTISSEMENT DE LA FCC : CET APPAREIL PEUT GÉNÉRER OU UTILISER DE L'ÉNERGIE DE RADIOFRÉQUENCE. TOUT CHANGEMENT OU MODIFICATION
DE CET APPAREIL PEUT ENTRAîNER DES INTERFÉRENCES NUISIBLES À MOINS QUE LES MODIFICATIONS NE SOIENT ExPRESSÉMENT APPROUVÉES DANS
LE GUIDE D'UTILISATION. L'UTILISATEUR RISQUE LE RETRAIT DE L'AUTORISATION D'UTILISER CET ÉQUIPEMENT SI UNE MODIFICATION OU UN CHANGEMENT
NON AUTORISÉ EST EFFECTUÉ.
MISE EN GARDE : POUR ÉVITER TOUT RISQUE DE CHOC ÉLECTRIQUE, INSÉREZ À FOND LA LAME LA PLUS LARGE DANS L'ORIFICE LE PLUS LARGE DE LA PRISE.
CET APPAREIL EST CONFORME À LA SECTION 15 DES RÈGLEMENTS DE LA FCC. LE FONCTIONNEMENT EST SOUMIS AUx DEUx CONDITIONS SUIVANTES :
(1) CE DISPOSITIF N'EST PAS CENSÉ CAUSER D'INTERFÉRENCES NUISIBLES, ET (2) CE DISPOSITIF DOIT RECEVOIR TOUTE INTERFÉRENCE, Y COMPRIS
CELLES POUVANT CAUSER UN FONCTIONNEMENT NON DÉSIRÉ.
REMARQUE : Cet appareil a été testé et approuvé comme étant conforme aux limites préconisées pour un appareil numérique de la classe B
conformément à la section 15 des réglementations de la FCC. Ces limites sont conçues pour fournir une bonne protection contre les interférences nuisibles
dans une installation domestique. Cet appareil génère, utilise et peut émettre de l'énergie de radiofréquence et, s'il n'est pas installé et utilisé conformément
aux instructions, peut perturber les communications radio. Cependant, il n'existe aucune garantie quant à l'absence d'interférences dans une installation
particulière. Si cet appareil cause des interférences nuisibles au niveau de la réception radio ou de la télévision, (ce qui peut être vérifié en l'allumant et en
l'éteignant), l'utilisateur doit essayer de remédier au problème en prenant les mesures suivantes :
• Réorientez ou repositionnez l'antenne réceptrice.
• Augmentez la distance qui sépare l'appareil du récepteur.
• Connectez l'appareil à une prise sur un circuit différent de celui utilisé par le récepteur.
• Consultez le revendeur ou un technicien radio/téléviseur expérimenté.
• La plaque signalétique est située à l'arrière de l'appareil.
PRÉCAUTIONS À PRENDRE AVEC LE LASER : Ce lecteur de disques compacts est doté d'un faisceau laser qu'il emploie pour la lecture des disques.
Seul du personnel dûment qualifié est autorisé à réparer cet appareil en raison des risques de blessure aux yeux.
ATTENTION : L'UTILISATION DES COMMANDES, DES RÉGLAGES OU L'ExÉCUTION DE PROCÉDURES QUI NE SONT PAS SPÉCIFIÉES NI DÉCRITES DANS
CE DOCUMENT PEUVENT ENTRAINER UNE ExPOSITION DANGEREUSE AU RAYON LASER.
PARASURTENSEURS : IL EST RECOMMANDÉ D'UTILISER UN PARASURTENSEUR POUR LE BRANCHEMENT SUR COURANT ALTERNATIF. LES DÉGâTS DUS À
LA FOUDRE ET AUx SURTENSIONS NE SONT PAS COUVERTS PAR LA GARANTIE QUI ACCOMPAGNE CE PRODUIT.
AVERTISSEMENT : POUR ÉVITER TOUT RISQUE D'INCENDIE OU DE DÉCHARGE ÉLECTRIQUE, N'EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L'HUMIDITÉ.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IMPORTANTES CONSIGNES DE SÉCURITÉ
1. Lisez ces consignes.
Si un chariot est utilisé, déplacez prudemment
2. Conservez ces consignes.
l'ensemble appareil et chariot pour éviter des
3. Tenez compte de tous les avertissements.
blessures causées par un basculement.
4. Suivez toutes les consignes.
13. Débranchez cet appareil pendant les orages ou
5. N'utilisez pas cet appareil à proximité de l'eau.
si vous prévoyez de ne pas l'utiliser pendant une
6. Nettoyez uniquement avec un chiffon sec.
longue période.
7. Ne bouchez pas les orifices prévus pour la ventilation. Installez
14. Confiez toute réparation à du personnel qualifié.
conformément aux instructions du fabricant.
Une réparation est nécessaire si l'appareil a été
8. N'installez pas l'appareil à proximité de sources de chaleur telles que
endommagé de quelconque manière, par ex. si le câble ou la fiche
les radiateurs, les grilles de chauffage, les cuisinières ou d'autres
d'alimentation est abîmé(e), ou du liquide a été renversé ou si des
appareils (y compris les amplificateurs) qui génèrent de la chaleur.
objets sont tombés dans l'appareil, ou encore si ce dernier a été exposé
9. Ne supprimez en aucun cas la fonctionnalité de sécurité de la fiche
à la pluie ou à l'humidité, ne fonctionne pas normalement, ou est tombé.
polarisée ou avec mise à la terre. Une fiche polarisée comporte deux
15. AVERTISSEMENT : Pour réduire le risque d'incendie ou de choc
lames avec une plus large que l'autre. Une fiche avec mise à la terre a
électrique, n'exposez pas cet appareil à la pluie ni à l'humidité. Aucun
deux lames et une troisième broche de mise à la terre. La lame large
objet contenant du liquide, comme un vase, ne doit être posé sur
ou la troisième broche ont été prévues pour votre sécurité. Si vous ne
l'appareil.
parvenez pas à brancher la fiche fournie dans votre prise, consultez un
16. La fiche secteur est utilisée comme dispositif de mise hors tension et
électricien afin qu'il remplace la prise obsolète.
doit rester aisément accessible et fonctionnelle à tout moment pendant
10. Protégez le cordon d'alimentation pour qu'il ne soit pas piétiné ou pincé
l'utilisation prévue. Pour mettre l'appareil totalement hors tension,
en particulier au niveau des fiches, des prises de courant et à l'endroit
retirez complètement la fiche de la prise secteur.
où il sort de l'appareil.
17. MISE EN GARDE : Pour réduire le risque d'incendie ou d'explosion,
11. Utilisez uniquement les fixations ou les accessoires recommandés par
n'exposez pas les piles à une chaleur intense, par exemple au soleil, au
le fabricant.
feu ou à d'autres sources de chaleur.
12. Utilisez uniquement avec un chariot, un pied, un trépied, un support ou
une table recommandé(e) par le fabricant ou vendu(e) avec l'appareil.
REVISION LEVEL
C
Spot
color
FINAL ARTWORK DATE
04/24/2013
Black
Pr ocess
1 color (black)
AC CONNECTION
Insert the AC plug (with the 2 blades) into a conveniently located AC outlet having 120V, 60Hz.
NOTE: The AC plug supplied with the unit is polarized to help minimize the possibility of electric shock. If the AC plug does
not fit into a nonpolarized AC outlet, do not file or cut the wide blade. It is the user's responsibility to have an electrician
replace the obsolete outlet.
BATTERY INSTALLATION
Two (2) "AAA" size batteries can be used to back-up the clock and alarm times as follows:
1. Open the Battery Compartment door
on the bottom of the unit by pressing the tab and
ck
lifting the cover off.
2. Insert two (2) "AAA" batteries into the Battery Compartment as shown. Be sure to observe
ADVERTENCIA DE CARRO PORTÁTIL
(símbolo proporcionado por RETAC)
the polarity markings which are engraved inside the battery compartment. Alkaline batteries
are recommended for the longest playing time.
3. Place the Battery Compartment door back on.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Warning – Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
2. Use only the size and type of batteries specified.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed battery may cause damage to
the device.
4. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh ones.
5. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
6. Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer's directions.)
7. Remove batteries promptly if consumed.
8. Clean the battery contacts and also those of the device prior to battery installation.
LOCATION OF CONTROLS
1
14
2
15
3
16
4
17
18
5
6
19
7
20
8
21
9
22
23
10
11
24
12
25
13
26
27
28
29
30
31
OPERATION
To Set the Time to Military (24 hour) or Standard (12 hour) Time:
1. With the power off, press and hold the Stop </Adjust button
for two seconds and the time will change to the next
bm
mode and "12H" or "24H" will blink in the display for three seconds; release the button.
To set or reset the actual time:
With the power off, you can set the time as follows:
1. Press the Stop </Adjust button
until the time blinks in the display.
bm
2. Press the Skip/Search 9/Minute button
to set the current minute.
an
3. Press the Skip/Search :/Hour button ap to set the current hour. If the 24/12 Hour setting is set to 12, make sure to
select the correct AM/PM setting (there is a PM indicator).
4. Press the Stop </Adjust button
when done setting.
bm
To set the alarm(s):
With the power off, you can set the alarm time(s) as follows:
1. Press the desired Alarm 1
or Alarm 2
button to enter the setting mode. The Alarm time will blink and the selected
U
x
alarm indicator will light.
AVERTISSEMENT SUR LES
2. Press the Skip/Search 9/Minute button
to set the alarm minute.
an
CHARIOTS PORTABLES
(Symbole fourni par RETAC)
3. Press the Skip/Search :/Hour button ap to set the alarm hour. If the 24/12 Hour setting is set to 12, make sure to
select the correct AM/PM setting (there is a PM indicator). Press the Alarm 1 U
4. Press the desired Alarm 1
or Alarm 2
button until the respective Alarm 1 or Alarm 2 indicator lights solid to
U
x
activate the alarm.
4a. TO WAKE TO THE BUZZER: Slide the Function switch
to the Buzzer position.
ct
4b. TO WAKE TO THE RADIO: Slide the Function switch
to the Radio position and slide the Band switch
ct
FM Stereo or AM position. Select a desired frequency using the Tuning control
comfortable waking level.
4c. TO WAKE TO A CD: Slide the Function switch
to the CD position and set the Volume control
ct
waking level.
5. When the actual time matches the selected preset alarm time, if set to Radio or Buzzer, the unit will automatically turn
on for 60 minutes and then shut off. If set to CD, the unit will only play the tracks on the CD and then shut off.
NOTES:
• While the alarm is sounding, if the other alarm reaches the alarm time, the first alarm will stop sounding and the second
alarm will start sounding.
• IMPORTANT: Make sure you have disconnected the audio cable from the Aux In jack (rear of the unit); otherwise, there
will be no sound when the actual time matches the preset alarm time.
Spot
color
If applicable.
Remove this box if
PMS
Pr ocess
2995C
this is a 1 color job.
2 color
OPERATION (CONTINUED)
To turn the alarm off:
To turn the alarm off, simply press the Standby/Alarm Off button ar. The alarm will turn off, but will remain set for the next
day. To turn the alarm off so it will not sound the next day, press the Alarm 1
alarm indicator disappears from the display.
Snooze:
While the alarm is sounding, press the Snooze button W. The alarm will turn back on automatically 9 minutes later. If
desired, press the Snooze button
again for another 9 minutes after the original Snooze time has been reached. You may
W
repeat this process up to ten times. To cancel the Snooze function, press the Standby/Alarm Off button ar.
Sleep:
With the unit in the CD or Radio mode, press the Sleep button V; the Sleep indicator and "90" will appear in the display
which indicates the unit will turn off after 90 minutes. Repeatedly press the Sleep button
(90, 60, 30, 15 and Off). To cancel the Sleep function, repeatedly press the Sleep button
After five seconds, the actual time will appear again and the Sleep indicator will disappear from the display.
Display Dimmer:
Repeatedly press the Dimmer (HI/LO) button y
to adjust the display brightness.
To Listen to the Radio:
1.
Press the Standby/Alarm Off button ar
to turn the unit on.
2. Slide the Function switch
to the Radio position and the Band switch
ct
Stereo does not come in well, set the Band switch to FM which will be Mono.
3. Tune a desired station by rotating the Tuning control. Rotate the unit for best reception.
4. Set the volume as desired using the Volume Control br.
5. To turn the unit off, press the Standby/Alarm Off button ar.
To Play a CD (Standard, CD-R and CR-RW):
1.
Press the Standby/Alarm Off button ar
to turn the unit on.
2. Slide the Function switch
to the CD position.
ct
1. CD Open Area
3. Lift the CD Open area
to open the CD door. Remove paper and Foam Shipping Protectors. Gently insert a CD onto
u
2. Program Button
the spindle (label side facing upwards) until it clicks. Close the CD door; the display will then show the number of tracks.
3. CD Mode Button
4. Press the Play/Pause4 ; button
to start playback. While in Playback mode, press the Play/Pause4 ; button
aq
4. Alarm 2 Button
pause; the current track will blink in the display. Press again to resume playback.
5. Dimmer (HI/LO) Button
5. To skip forward or backward through the tracks on the disc, press the Skip/Search 9
6. Alarm 1 Button
forward or backward through the tracks on the disc, press and hold the Skip/Search 9
7. Sleep Button
6. Set the volume as desired using the Volume Control br.
8. Snooze Button
7. To view the CD info on the display, press the CD Display button as.
9. PM Indicator
8. When the disc is done playing, it will stop automatically. Press the Stop </Adjust button
10. Alarm 1 Indicator
is finished. To turn the unit off, press the Standby/Alarm Off button ar.
11. Program Indicator
Note: If a disc is not present or if it is inserted incorrectly, dirty or damaged (disc cannot be read), the display will show "no".
12. Sleep Indicator
13. Repeat Indicator
To Use the Repeat and/or Random Functions:
14. Skip/Search 9/Minute Button
15. AC Power Cord (Rear of Unit)
1. Insert a CD as described above and start playback.
16. Skip/Search :/Hour Button
2. Press the Skip/Search 9
or :
button to select a track to repeat.
an
ap
17. Play/Pause4 ; Button
3. Press the CD Mode button
once; the Repeat indicator will blink and the unit will play the same track over and over
w
18. Standby/Alarm Off Button
until the Stop </Adjust button
is pressed.
bm
19. CD Display Button
4. Press the CD Mode button
a second time; the Repeat indicator will light solid and the unit will then play all the tracks
w
20. Tuning Control
on the CD over and over until the Stop </Adjust button
21. Headphone jack
5. Press the CD Mode button
w
a third time; the Random indicator will light and the unit will randomly play each track
22. Band (AM/FM/FM Stereo) Switch
on the CD and then stop.
23. Stop </Adjust Button
6. Press the CD Mode button
a fourth time; the Repeat and Random indicators will go off and standard playback will
w
24. Alarm 2 Indicator
resume.
25. Random Indicator
26. FM Stereo Indicator
To Program the Memory (up to 20 tracks):
27. Snooze Indicator
1. With a CD inserted and in Stop mode, press the Program button
28. Volume Control
Program indicator will blink.
29. Aux In jack
2. Select the first track to be played back using the Skip/Search 9
30. Function (Radio/Buzz/CD) Switch
again. Repeat this step to program additional tracks, up to a maximum of 20 tracks.
v
31. Battery Compartment (Bottom of unit)
3. Press the Play/Pause4 ; button
to begin playback; the Program indicator will light solid. Adjust the volume control
aq
(BATTERY COVER PART NO.:
as desired. The unit will play all the tracks in the order you programmed them.
WM2759001*)
4. To skip forward or backward through the programs, press the Skip/Search 9
*Consumer Replaceable Part
5. When the disc is done playing, it will stop automatically. Press the Stop </Adjust button
(See end of guide to order.)
is finished.
Notes:
• Programming is the ability to preselect the order in which a series of tracks will be played.
• To stop and clear the program memory: While in Program Stop mode, press the Stop </Adjust button
"PROG" indicator will go off.
Aux In Jack:
With the unit on, insert one end of an audio cable (not included) into the LINE OUT jack on your external audio unit and
the other end into the Aux In jack
on this unit; the unit will automatically enter the AUx mode. Start playback of the
bs
external unit and its audio output sound will be heard through this unit's speakers. Disconnect the cable from the Audio In
jack to resume listening to the previous mode.
Note: If you are in Radio or CD mode, when you connect an external audio unit to the Aux In jack, this unit will
automatically switch to AUx mode. If you remove the plug from the Aux In jack, the unit will revert to the mode it was in
before the external unit was connected.
Headphones Jack:
For private listening, connect 3.5 mm (32 ohm) stereo headphones (not included) to this jack. The speakers are
automatically disabled when the headphones plug is inserted in the jack.
SPECIFICATIONS AND COMPATIBILITY
or Alarm 2
button again.
x
Frequency Range (AM) ........................................ 530 - 1700 KHz
Frequency Range (FM) ........................................... 88 - 108 MHz
Disc Diameter ............. 4.72" (120 mm), 3.15" (80 mm) Single CD
Optical Source .............................................Semiconductor Laser
to the FM,
bl
Dimensions ............................. 5.7 (W) x 7.1 (D) x 3.15 (H) inches
and set the Volume control
to a
bt
br
Specifications are subject to change without notice.
to a comfortable
br
Imation Enterprises Corp.
1 Imation Way, Oakdale, MN 55128-3414 USA
© Imation Corp. www.memorex.com
Memorex and the Memorex logo are trademarks of Imation Corp and its affiliates. All other trademarks are the property of their
respective owners.
For additional setup, operating assistance or an electronic version of this user manual, please visit www.memorex.com
For consumer replaceable part(s), verify part number(s) then contact our parts and accessory fulfillment center at: 1-800-379-8439
User Guide
Please read these instructions completely
before operating this product
memorex.com
MC7223
or Alarm 2
button repeatedly until the
U
x
to select the desired sleep time
V
until the Sleep indicator goes off.
V
to the AM, FM or FM Stereo position. If FM
bl
to
aq
an
or :
ap
button. To search
or :
button.
an
ap
to stop the disc before it
bm
is pressed.
bm
once; "P 01" will appear oin the display and the
v
or :
button, then press the Program button
an
ap
or :
button.
an
ap
to stop the disc before it
bm
and the
bm
Weight ......................................................................... 3.3 lbs
Wavelength ................................................................. 780 nm
Power Supply ................................................ 120 V AC, 60 Hz
Battery Backup ........................... 2 x 1.5 V "AAA" size batteries
...........................................................................(not included)
73952890C

Advertisement

loading
Need help?

Need help?

Do you have a question about the MC7223 and is the answer not in the manual?

Questions and answers

Toni Corbell
March 14, 2025

I want not to have this service

Toni Corbell
March 14, 2025

I want to decline a payment

Summary of Contents for Memorex MC7223

  • Page 1 NOTES: Memorex and the Memorex logo are trademarks of Imation Corp and its affiliates. All other trademarks are the property of their 10. Protégez le cordon d’alimentation pour qu’il ne soit pas piétiné ou pincé...
  • Page 2: Instalación De La Batería

    Memorex y el logotipo Memorex son marcas comerciales de Imation Corp y sus filiales. Las demás marcas comerciales son Memorex et le logo Memorex sont des marques de commerce d’Imation Corp et de ses sociétés affiliées. Toutes les autres • Si la seconde alarme se déclenche pendant que la première retentit, la première alarme s’arrête et la seconde commence NOTAS: propiedad de sus respectivos dueños.
Save PDF