Advertisement
1
7
5
6
NOTE: If in doubt, refer to Fig 1 for part location in relation to machine.
1. Affix Handle to operating position. (Fig 2)
2. Remove Recovery Tank (Fig 3), Clear Dome and Transfer Hoses.
3. Fill Solution Tank with clean water (at a maximum of 60°C) and solution mixture (max. 15 ltrs) via the
opening at the front of the Solution Tank.
4. Replace Top Tank , Clear Dome and Transfer Hoses , ensuring correct seating.
5. Check mains cable for visible damage, If non detected, Plug into mains socket. If damage detected , do
not proceed and refer to safety instructions.
6. When the machine is plugged in ,ensure Green Indicator Light comes on.
7. Activate switches to choose cleaning options as follows: (Fig 5)
A) Brush.
B) Vacuum.
C) Pump. (Amber light will come on when in use)
NOTES:
•
Ensure selector switch is set to Brush position. (Fig 6)
•
Although the functions work independently , to operate the machine normally, only turn on the Brush and
Vacuum switches.
•
Use the Handle Trigger for controlled solution spray (Fig 7) (Amber light will come on).
•
If extra cleaning is needed before picking up water, use just the Brush and Pump switches.
•
For constant spray, press the Pump switch to its on position. (normally used when the Carpet or
Upholstery tools are in use).
•
The machine has been designed to be pulled towards the operator, not pushed away from the
operator.
Always remove plug from mains socket outlet before carrying out any routine maintenance, cleaning,
brush removal or converting the appliance to another application.
8.
The pump has been fitted with a thermal trip to protect it from overheating. To prevent this , during
operation, the operator should visually check that there is constant water flow by looking at the clear
section of the hoses (Fig 8 & 9) . If the appliance is allowed to run dry the trip will activate,
pump light will go out and the appliance will cease to function. If this occurs, switch off the pump , refil the
appliance with water/solution and allow upto 20 minutes for pump to cool and reset before re-starting.
9.
If any foam is detected in the clear dome during operation, turn the machine off (unplug from the mains)
and either empty the machine or add defoamer to the recovery tank .
Always empty and clean Tanks after use. Only drain the Tanks and deposit soiled water or solution into
10. To empty the Recovery Tank, remove the Clear Dome, and Transfer Hoses and empty Tank.
11. To empty the Solution Tank , remove the Dump Hose from the Solution Tank and allow the solution to
flow out. ( See Above for drainage). The solution hoses shows the operator the level of cleaning solution
in the tank (Fig 9). Do not allow the level to drop below the black coloured section of the Dump Hose.
12. If during normal operation, the brush stops or cuts out ,press and hold the reset button for a few
seconds. The machine can then be restarted in the normal manner (Fig 5 D). If problem persists contact
your Victor service agent.
13. If during operation ,the Spray Jet ceases to spray solution, remove plug from socket outlet, remove the
Transfer Hoses, Recovery Tank and Clear Dome then tilt the machine back. (to gain access to the nozzle)
Remove the spray nozzle (located on the underside of the machine) by twisting it from its housing. Clean
the nozzle under a tap to release any dirt. Once done, replace the nozzle. (Fig 10).
14. If it becomes necessary to remove or check the brush , remove plug from mains socket outlet , remove
the Transfer Hose, Recovery Tank and Clear Dome, tilt the machine back to gain access to the brush.
To remove the brush turn the locking knob in the direction printed on it. (Fig 12). Once the locking knob
has been removed the brush can be removed by pulling it to the right then out. (Fig 11). When re-fitting
brush, ensure White Indicator bristles are on the R/H side (as shown).
15. If prior or during operation, damage is detected on the power cable, remove plug from the mains.
The cable can be removed from the machine by removing the attaching screw and replaced with a new
cable pack means of the attaching screw. (Fig 5 E). See Safety Instructions prior to carrying out this operation
1.1
Handle with solution trigger
1.2
Switches.
1.3
Transfer Hoses.
1.4
Recovery Tank.
1.5
Floor Drying Feature.
1.6
Floor Squeegee
1.7
Clear Dome.
3
1.8
Solution Tank
4
Fig 1
8
(Fig 4.)
safe, suitable approved locations.
FEATURES OF THE V-SX 15
9
10
11
OPERATING INSTRUCTIONS
the
amber
2
12
14
13
Fig 2.
Fig 6.
Fig 7.
Fig 9.
Fig 11.
1.9 Coupling Socket.
1.10
Selector Switch
1.11
Reset Button.
1.12
Electronics Enclosure.
1.13
Solution Tank Dump Hose /
Fluid Indicator
1.14
Quick Change Cable Pack
Fig 3.
Fig 4.
B
C
A
E
D
Fig 5.
Fig 8.
Fig 10.
Fig 12.
Advertisement
