Table of Contents
Advertisement
Countdown Timer
You can set the countdown timer within a range
Minutes Seconds
of one to 60 minutes. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are
performed in the Countdown Timer Mode,
which you enter by pressing C.
To set the countdown start time
1. While the countdown start time is on the
Timekeeping
display in the Countdown Timer Mode, hold
Mode time
down A until the current countdown start time
1/10 second
starts to flash, which indicates the setting
screen.
• If the countdown start time is not displayed, use the procedure under
"To use the countdown timer" to display it.
2. While a setting is flashing, use D (+) and B (–) to change it.
3. Press A to exit the setting screen.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm sounds for 10
seconds or until you stop it by pressing any button. The countdown time is
reset automatically to its starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D
again to resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D),
and then press B. This returns the countdown time to its starting value.
Alarms
You can set five independent Daily Alarms. When
Alarm time (Hour : Minutes)
an alarm is turned on, the alarm tone sounds when
the alarm time is reached. One of the alarms can
be configured as a snooze alarm or a one-time
alarm, while the other four are one-time alarms.
You also can turn on an Hourly Time Signal that
causes the watch to beep twice every hour on the
hour.
• There are five alarm screens numbered 1
through 5. The hourly time signal screen is
Timekeeping Mode time
indicated by
• When you enter the Alarm Mode, the screen
Alarm number
you were viewing when you last exited the
mode appears first.
• All of the operations in this section are
performed in the Alarm Mode, which you enter
by pressing C.
To set an alarm time
1. In the Alarm Mode, use D to scroll through
the alarm screens until the one whose time
you want to set is displayed.
x1
:00
• You can configure Alarm 1 as a snooze alarm or a one-time alarm.
Alarms 2 through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm
time starts to flash. This indicates the setting screen.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set
the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the
snooze alarm, the alarm operation is performed a total of seven times, every
five minutes, or until you turn the alarm off or change it to a one-time alarm.
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval
between snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm 1 setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
Operation Guide 3108
:
00
x2
x3
x5
x4
To turn Alarms 2 2 2 2 2 through 5 5 5 5 5 on and off
1. In the Alarm Mode, use D to select a one-
time alarm (alarm number 2 through 5).
2. Press B to toggle the displayed alarm on and
off.
• Turning on a one-time alarm (2 through 5)
displays the one-time alarm on indicator on
the alarm screen. The one-time alarm on
indicator also is displayed in all modes when
One-time alarm on
indicator
any alarm is on.
To select the operation of Alarm 1 1 1 1 1
1. In the Alarm Mode, use D to select Alarm 1.
2. Press B to cycle through the available settings in the sequence shown
below.
Snooze alarm on indicator and one-time alarm on indicator
One-time alarm on
Snooze alarm on
• The applicable alarm on indicator is displayed in all modes when an alarm
is turned on.
• The snooze alarm on indicator flashes during the 5-minute intervals
between alarms.
• Displaying the Alarm 1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
To turn the hourly time signal on and off
1. In the Alarm Mode, use D to select the
Hourly Time Signal (
2. Press B to toggle it on and off.
• Turning on the Hourly Time Signal displays the
hourly time signal on indicator in all modes.
Hourly time signal on
indicator
Illumination
The watch has an EL (electro-luminescent) panel
that causes the entire display to glow for easy
reading in the dark. The watch's auto light switch
illuminates the display automatically when you
angle the watch towards your face.
• The auto light switch must be turned on
(indicated by the auto light switch indicator) for
it to operate.
Auto light switch
• See "Illumination Precautions" for other
indicator
important information.
To turn on illumination manually
In any mode, press L to illuminate the display
for about one second.
• The above operation turns on illumination
regardless of the current auto light switch
setting.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on whenever you
position your wrist as described below in any mode. Note that this watch
features a "Full Auto EL Light," so the auto light switch operates only when
available light is below a certain level. It does not illuminate the display under
bright light.
Moving the watch to a position that is parallel to the ground and then tilting
it towards your face at more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Parallel to
ground
Alarm off
00).
:
More than
40°
4
Advertisement
Table of Contents
