Advertisement
USER'S GUIDE 2534/2654
To recall Telememo records
In the Telememo Mode, use D (+) and B (–) to scroll through Telememo records on
the display.
• Pressing D while the last Telememo record is on the display or B while the first
record is on the display displays the new data screen.
To edit a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes that you want, press A to store them and return to the
Telememo record screen.
To delete a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Hold down D and B until the watch beeps and
display.
• The message
CLR
appears, which indicates that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Telememo record screen.
World Time
The World Time Mode shows you the current time in 27
GMT differential
cities (29 time zones) around the world.
• The time settings of the Timekeeping Mode and the
City Code
World Time Mode are independent from each other, so
you must make separate settings for each.
• Whenever you change the time setting for any city in the
World Time Mode, the settings of all other cities are
changed accordingly.
• For full information on city codes, see the "City Code
Table".
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Timekeeping Mode time
Current time in the zone
of the selected city code
To view the time in another city code
In the World Time Mode, press D to scroll through city codes (time zones) to the east
or B to scroll to the west.
To set the World Time
1. In the World Time Mode, use D and B to scroll
through the city code (time zone) and find the one you
want.
2. Hold down A until the hour setting of the world time
starts to flash, which indicates the setting screen.
3. Press C to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use D (+) and B (–) to
change it.
5. Press A to exit the setting screen.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D and B to display the
city code whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A until the hour setting of the world time
starts to flash, which indicates the setting screen.
3. Press L to toggle Daylight Saving Time ( displayed)
and Standard Time ( not displayed).
4. Press A to exit the setting screen.
• The Daylight Saving Time indicator
GMT differential is on the display only. It does not
appear while the city code is on the display.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while
city code.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
• The
indicator is on the display whenever you display a
city code for which Daylight Saving Time is turned on.
Countdown Timer
Minutes
Seconds
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer has two
modes: auto-repeat and elapsed time, and a progress
beeper signals the progress of the countdown. All of this
makes the countdown timer a valuable tool for timing the
start of a yacht race.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
Timekeeping Mode time
C.
Configuring the Countdown Timer
The following are the settings you should configure before actually using the
countdown timer.
Countdown start time and reset time
Timer mode (auto-repeat, elapsed time)
Progress beeper on/off
• See "To configure the countdown timer" for information about setting up the timer.
CLR
stops flashing on the
appears while the
GMT
is selected as the
Reset Time
You can set a "reset time," which is a kind of alternate countdown start time you can
recall with the press of a button any time a countdown operation is in progress.
Timer Mode
The countdown timer gives you a choice of two modes: auto-repeat and elapsed time.
Auto-repeat
Auto-repeat mode automatically restarts the countdown from the countdown start time
you set whenever zero is reached.
• Auto-repeat mode is best when timing the starts of match races.
• Even if you start a countdown operation from the reset time, the countdown
automatically restarts from the countdown start time whenever it reaches zero.
• Auto repeat timing repeats up to seven times.
Elapsed Time
When the end of the countdown is reached in the elapsed time mode, the timer
automatically switches to an elapsed time measurement operation.
• The elapsed time mode is best when timing the speed of yachts during ocean races.
• The elapsed time operation is performed in one-second increments up to 99 hours,
59 minutes, 59 seconds.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown reaches
zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than
the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal
when the countdown reaches zero.
• The countdown end beeper always sounds, regardless of the on/off status of the
progress beeper.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and a reset
period progress beeper.
• The reset time beeper and reset period progress beeper sound only while the
progress beeper is turned on.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. When the progress
beeper is turned on, the watch beeps each second of the final 10 seconds before the
countdown reaches the reset time.
Reset Period Progress Beeper
The reset period is the portion of the countdown between the reset time and zero.
When the progress beeper is turned on, the watch emits four short beeps at the top of
each minute during the reset period, and 30 seconds before the end of the
countdown.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;
Progress beeper: On
Reset Period
Start Time
Reset Time
Reset Period Progress Beeper
10'00"
5'00"
4'00"
3'00"
Reset Time Beeper
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;
Progress beeper: Off
Start Time
Reset Time
10'00"
5'00"
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the
countdown start time setting starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under "To use the countdown timer" to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start
Time
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
Screen
Use D (+) and B (–) to change the setting.
Start Time
• You can set a start time in the range of 1 to 60 minutes
in 1-minute increments.
Use D (+) and B (–) to change the setting.
Reset Time
• You can set a reset time in the range of 1 to 5 minutes
in 1-minute increments.
Press D to toggle between the auto-repeat mode (ON)
Timer Mode
and the elapsed time mode (OFF).
• An auto-repeat indicator (
repeat mode is selected.
Press D to toggle progress beeper on (ON) and off (OFF).
Progress
• A progress beeper indicator ( ) appears when this
Beeper
setting it turned on.
4. Press A to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
Countdown
End Beeper
2'00"
1'00" 0'30"
0'00"
Elapsed time
measurement
0'00"
Countdown
End Beeper
Reset
Timer
Progress
Time
Mode
Beeper
Button Operations
) appears when the auto-
2
Advertisement
