5-1. IC PIN DESCRIPTION
• IC801 CXP82220-051Q (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
A-PLAY
2
POWER IN (CED)
3
—
4
SIRCS
5
—
6
RECVOLOUT
7
—
8
BUSIN
9
POWER OUT
10
POWER IN (U)
11
A-SHUT
12
A-SHUMIT
13
CAPM (H/L)
14
PITCH.CON
15
—
16
BUSOUT
17
LINE MUTE
18
LPF
19
RECMUTE
20
B-BIAS
21
NR SW
22
B-IV
23
PB SELECT (A/B)
24
REC/PB
25
PBEQ (HIGH/NORM)
26
NR/MUTE/PASS
27
AMSOFF/AMS/BS
28
B-RELAY
29
B-SHUT
30
B-SHUMIT
31
B-PLAY
32
B-HALF
33
METER (L)
34
METER (R)
35
KEY3
36
KEY1
37
KEY2
38
RESET
39
XIN
40
XOUT
41
VSS
42
—
43
—
44
KEY4
45
RECVOL IN
46
—
47
—
48 – 50
—
51
ARL (LED)
52
SYNC (LED)
53, 54
—
SECTION 5
DIAGRAMS
I/O
I
Play switch input (DECK A)
I
Power-in detection input
—
Connected to ground.
I
Sircs signal input
—
Connected to ground.
O
Record level control output (PWM)
—
Not used in this set.
I
Control A signal input
O
Power hold output
I
Power-in detection input
I
Capstan motor rotation detection input (DECK A)
I
Capstan motor rotation detection input (DECK A)
O
Capstan motor high/normal select output "L":ON
O
Pitch control ON/OFF output "L":ON
—
Not used in this set.
O
Control A signal output
O
Line mute ON/OFF control output "L":Mute ON
O
Low pass filter on output
O
Recording mute output "L":Mute ON
O
Bias ON/OFF output (DECK B) "H":ON
O
Dolby selector "H":C, "Open":B, "L":Dolby off
I
Metal detection input (DECK B)
I
Playback A/B selector input "L":A, "H":B
O
Record/playback dolby NR mode selector output "L":Playback
O
PB EQ high/normal select output "L":Normal
O
Audio selector "H":Pass, "Open":Mute, "L":Dolby
O
AMS amp selector "H":BS, "Open":AMS, "L":OFF
O
Relay record/playback selector output (DECK B) "L":Record
I
Capstan motor rotation detection input (DECK B)
I
Capstan motor rotation detection input (DECK B)
I
Play switch input (DECK B)
I
Half switch input (DECK B)
I
Meter L-CH input (A/D converter)
I
Meter R-CH input (A/D converter)
I
Key 3 input (A/D converter)
I
Key 1 input (A/D converter)
I
Key 2 input (A/D converter)
I
System reset input
I
System clock oscillator input (10 MHz)
O
System clock oscillator output (10 MHz)
—
Ground
—
Connected to ground.
—
Connected to ground.
I
Key 4 input (A/D converter)
I
Record volume input (A/D converter)
—
Connected to power supply.
—
Connected to ground.
—
Not used in this set.
O
AUTO LED driver "H":ON
O
SYNCHRO LED driver "L":ON
—
Not used in this set.
– 14 –
Pin Description