Advertisement
Quick Links
Advertisement
Related Manuals for Lanzar VIBE VIBE1801D
Summary of Contents for Lanzar VIBE VIBE1801D
-
Page 2: Table Of Contents
T A B L E O F C O N T E N T S 1. Contents 2. Introduction 3. Features 4. Specifications 5. Amplifier installation 6.7. Features and controls 8.9.10.11. System wiring 12.13. Troubleshooting I B E W N E R ’ S A N U A L —... -
Page 3: Introduction
N T R O D U C T I O N Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service. The VIBE Class-D amplifier has been designed using the latest in electronic technology available today. -
Page 4: Features
CLASS-D DESIGN Low - frequency information for subwoofer only. High efficient power POWER SUPPLIES Stiffly regulated PWM power supplies. MOSFET switches maintain rated power over a wide range of battery voltages. LOW PASS FILTER Adjustable from 50Hz to 150Hz with a slope of 24dB per octave. This allows for the adjustment of the upper point of the frequency bandwidth and the respective subwoofer. -
Page 5: Specifications
P E C I F I C A T I O N S MODEL RMS Power, INTO 4 Ohms RMS Power, INTO 2 Ohms RMS Power, INTO 1.3 Ohms MAX Power, INTO 1.3 Ohms BRIDGE MAX Power, INTO 2 Ohms THD at 1 Watt, 4 Ohm Signal-to-Noise Ratio, below rated power output Frequency Response, at 1Watt,4 Ohm... -
Page 6: Amplifier Installation
1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. - Page 7 E A T U R E S A N D VIBE1801D VIBE3200D — I B E W N E R ’ S A N U A L O N T R O L S Phase Level sonic shift Pass Min Max 15Hz 40Hz 50Hz 150Hz 0°...
-
Page 8: Features And Controls
1. Line Out RCA Jacks - The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. - Page 9 Y S T M I R I N G SIGNAL INPUT AND BYPASS OUTPUT CONNECTION TO SATELLITE AMPLIFIER LINE-INPUT SPEAKER OUTPUT CONNECTION LEVEL to REMOTE GAIN CONTROLLER — I B E W N E R ’ S A N U A L Phase Bass Level...
- Page 10 SIGNAL INPUT AND BYPASS OUTPUT CONNECTION TO SATELLITE AMPLIFIER LINE-INPUT SPEAKER OUTPUT CONNECTION SUBWOOFER Line Line Input Subsonic LowPass Bass Input Level Filter PHASE Filter Boost 0° 180° 10Hz 40Hz 50Hz 150Hz 18dB Remote .1V 2V 2V 8V Master Slave Input sensitivity Bridged mode Data Link LEVEL...
- Page 11 Y S T E M I R I N G to INPUTS OF SATELLITE AMPLIFIER 1 0 — I B E W N E R ’ S A N U A L Master Slave BRIDGED SWITCH ; MASTER POSITION Phase Bass Level sonic...
- Page 12 BRIDGING TWO AMPLIFIERS Master Slave Master Amp Line Line Input Subsonic LowPass Bass Input Level PHASE Filter Filter Boost 0° 10Hz 40Hz 50Hz 150Hz 18dB .1V 2V 2V 8V Master Slave Input sensitivity Bridged mode Data Link From OUTPUTS of HEAD UNIT Slave Amp Line...
-
Page 13: Troubleshooting
R O U B L E S H O O T I N G Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. M P L I F I E R W I L L N O T P O W E R U P . I G H H I S S O R E N G I N E N O I S E ( A L T E R N A T O R W H I N E ) I N S P E A K E R S . - Page 14 RO TECTION LED C OMES ON W H EN T H E A MP LI F I E R IS PO WE R E D UP Check for shorts on speaker leads. Check that the volume control on the head unit is turned down low. Remove speaker leads and reset the amplifier.