Advertisement
Quick Links
Congratulations on your purchase of a Lanzar Viberant amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. Vibe amplifiers are designed with the
latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges
found on modern CD's and recordings.
Table of Contents
Feature and Controls
System Wiring
1. Vibe218/228/238/248/258/268
6. 2 channel stereo
2. Vibe418/428/438
7. 2 channel bridged mode
3. Installation
8. 2 channel tri-mode
4. Specifications
9. 2 channel triamp system
10. 4 channel stereo
11. 4 channel bridged mode
12. 4 channel tri-mode
13. Precautions
14. Troubleshooting
Advertisement
Related Manuals for Lanzar VIBE218
Summary of Contents for Lanzar VIBE218
- Page 1 Congratulations on your purchase of a Lanzar Viberant amplifier. You have purchased a quality product designed and engineered to give you many years of uncompromised musical service. Vibe amplifiers are designed with the latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges found on modern CD's and recordings.
- Page 2 1 2 3 7 6 5 1. INPUT LEVEL CONTROLS Enables the matching of input levels to the output levels from head unit (or other signal source). 2. CROSSOVER MODE SELECTOR Determines the mode of built-in crossover: low pass (permits only low frequency signals to pass to speakers),high pass (permits only high frequency signals to pass to speakers), or flat.
- Page 3 v i b e 4 1 8 / 4 2 8 / 4 3 8 vibe418 2 3 476 1. REMOTE BASS BOOST (vibe428/438) Plug in the remote bass boost control wire in here 2. INPUT LEVEL CONTROLS Enables the matching of input levels to the output levels from head unit (or other signal source).
- Page 4 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length.
- Page 5 Vibe218 2 x 100W 2 x 200W 1 x 400W At 4 Ohms Bridged 2 x 150W 2 Ohm Min. Speaker Impedance 0.04% 15Hz-35KHz, -1dB 250mV-5000mV 22 KOhm >90dB >65dB 35Hz-400Hz 80Hz-2.50KHz +18dB 11.5"x2.3"x8" Vibe 228 Vibe 238 2 x 150W...
- Page 6 Vibe258 Vibe 268 2 x 400W 2 x 500W 2 x 800W 2 x 1000W 1 x 1600W 1 x 2000W 2 x 650W 2 x 800W 2 Ohm 2 Ohm 0.04% 0.04% 15Hz-35KHz, -1dB 15Hz-35KHz, -1dB 250mV-5000mV 250mV-5000mV 22 KOhm 22 KOhm >90dB >90dB...
- Page 7 L/R Audio Outputs To Battery To Remote Output From Head Unit LEFT speaker RIGHT speaker...
- Page 8 To a second amplifier Y Adaptors To Battery To Remote Output From Head Unit Speaker...
- Page 9 To Battery To Remote Output From Head Unit LEFT speaker vibe218/228/238/248/258/268 head unit RIGHT speaker Speaker...
- Page 10 vibe218/228/238/248/258/268...
- Page 11 vibe418/428/438 head unit To Battery To Remote Output From Head Unit...
- Page 12 vibe418/428/438 head unit To Battery To Remote Output From Head Unit...
- Page 13 vibe418/428/438 To Battery To Remote Output From Head Unit...
- Page 14 • Before you drill or cut any holes, investigate your car's layout very carefully. Take care when your work near the gas tank, fuel lines, hydraulic lines and electrical wiring. • Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident.
- Page 15 • Check for good ground connection. • Check that remote DC terminal has at least 12V DC. • Check that there is battery power on the "+" terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. •...