Sony D-NE320SP Service Manual page 18

D-NE320SP/NE329LIV/NE329SP
Ver. 1.1
QQ
3 7 63 1515 0
Pin No. Pin Name
157 FILO
158 FILI
159 PCO
160
VSS12
161
DVDD3
162
VDIODSP
163 SFDR
164
SRDR
165
TFDR
166
TRDR
167 FFDR
168
FRDR
169
MDP
170
MDS
171 C176
172
VDIOEM0
173
DVDD4
174
VSS14
175 PC3/XSCS0
176
PC2/SI0
177
PC1/SO0
TE
178 L 13942296513
PC0/SCK0
179 VSS15
180
VDIO5
181
PG7
182, 183
PG6, PG5
184
PG4
185, 186
PG3, PG2
187 PG1
188 PG0
189, 190
DVDD5, DVDD6
191 VSS18
192
AVDAD
193
AVSAD
194
AN7
195 AN6
196
AN5
197
AN4
198
AN3
199, 200
AN2, AN1
201 AN0
www
202
WAKE
203
XADEVENT
204
XRST
.
205, 206
DVDBK0, DVDBK1
207
VSS19
208
VDIO6
18
http://www.xiaoyu163.com
I/O
O
Filter output terminal for master PLL
I
Filter input terminal for master PLL
O Charge pump output terminal for master PLL
- Ground terminal
- Power supply terminal (+1.3V)
- Power supply terminal (+2V)
O Sled servo drive signal (+) output to the motor/coil drive
O Sled servo drive signal (-) output to the motor/coil drive
O Tracking servo drive signal (+) output to the motor/coil drive
O Tracking servo drive signal (-) output to the motor/coil drive
O Focus servo drive signal (+) output to the motor/coil drive
O Focus servo drive signal (-) output to the motor/coil drive
O Spindle motor servo drive signal output to the motor/coil drive
- Not used
O 176.4 kHz clock signal output to the motor/coil drive
- Power supply terminal (+2V)
- Power supply terminal (+1.3V)
- Ground terminal
O Command latch signal output to the power control
I Serial data input from the EEPROM
O Serial data output to the power control and EEPROM
O Serial clock signal output to the power control and EEPROM
- Ground terminal
- Power supply terminal (+2V)
I Cold start flag input from the power control
- Not used
O Reset signal output to the liquid crystal display
- Not used
O Standby signal output to the optical pick-up block
O RF gain-up signal output for CD-RW to the optical pick-up block
- Power supply terminal (+1.3V)
- Ground terminal
- Power supply terminal (+2V)
- Ground terminal
I CD lid open/close switch input terminal "L": close, "H": open
I Charge voltage monitor input from the power control
I Battery voltage monitor input terminal
Wake up signal input from the power control
I
Remote commander key input terminal (NE320SP: Asian area in E and Tourist models only)
- Not used
I Top panel key input terminal (A/D input)
I DCIN voltage monitor input terminal
I Wake up signal input terminal
O Wake up signal output to the power control
x ao
y
I System reset signal input from the power control
i
- Power supply terminal (+1.2V)
- Ground terminal
- Power supply terminal (+2V)
http://www.xiaoyu163.com
8
Description
Q Q
3 6 7 1 3
u163
.
2 9 9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
9 9
2 8 9 9