D-Link DSL-2730E User Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Wireless Router
  5. DSL-2730E
  6. User manual

D-Link DSL-2730E User Manual

Wireless n 150 adsl2+ modem router
Hide thumbs Also See for DSL-2730E:
Table of Contents

Advertisement

Quick Links

D-Link DSL-2730E
Wireless N 150 ADSL2+ Modem Router

User Manual

RECYCLABLE
2014/08/14
Ver. 1.00

Advertisement

Table of Contents
loading

Related Manuals for D-Link DSL-2730E

Summary of Contents for D-Link DSL-2730E

  • Page 1: User Manual

    D-Link DSL-2730E Wireless N 150 ADSL2+ Modem Router User Manual RECYCLABLE 2014/08/14 Ver. 1.00...

  • Page 2: Table Of Contents

    DSL-2730E User Manual Contents Introduction...................... 1 Packing List ..................1 Safety Precautions ................1 LEDs and Interfaces ................2 System Requirements ................. 4 Features ....................4 Hardware Installation ..................6 Web Configuration ................... 7 Accessing the Device ................7 Setup ....................9 3.2.1...
  • Page 3 DSL-2730E User Manual 3.4.4 Diagnostics ................ 83 3.4.5 System Log ............... 86 3.4.6 Logout ................88 Status ....................88 3.5.1 Device Info ................ 88 3.5.2 Wireless Clients ..............90 3.5.3 DHCP Clients ..............90 3.5.4 ADSL Driver ..............91 3.5.5 Statistics ................

  • Page 4: Introduction

    DSL-2730E User Manual Introduction The DSL-2730E supports multiple line modes. With four 10/100 base-T Ethernet interfaces at the user end, the device provides high-speed ADSL broadband connection to the Internet or Intranet for high-end users like net bars and office users.

  • Page 5: Leds And Interfaces

    DSL-2730E User Manual Do not put this device close to a heat source or under a high temperature  occurs. Keep the device away from direct sunshine. Do not put this device close to an overdamp or watery place. Do not spill ...
  • Page 6 DSL-2730E User Manual Color Status Description Data is transmitted through the WLAN Blinks interface. The connection of WLAN interface is WLAN Green normal. The WLAN connection is not established. WPS negotiation is enabled, waiting for Blinks the clients. Blue WPS negotiation is not enabled on the device.

  • Page 7: System Requirements

    DSL-2730E User Manual The following table describes the interface of the device. Interface/Button Description Antenna position RJ-11 interface that connects to the telephone set through the telephone cable. Ethernet RJ-45 interfaces that connect to the Ethernet LAN4/3/2/1 interfaces of computers or Ethernet devices.
  • Page 8 DSL-2730E User Manual Multiple PVCs (eight at most) and these PVCs can be isolated from each  other A single PVC with multiple sessions  Multiple PVCs with multiple sessions  Binding of ports with PVCs  802.1Q and 802.1P protocol ...

  • Page 9: Hardware Installation

    DSL-2730E User Manual Hardware Installation Step 1 Connect the DSL port of the device and the Modem port of the splitter with a telephone cable. Connect the phone to the Phone port of the splitter through a telephone cable. Connect the incoming line to the Line port of the splitter.

  • Page 10: Web Configuration

    DSL-2730E User Manual Web Configuration This chapter describes how to configure the device by using the Web-based configuration utility. 3.1 Accessing the Device The following is the detailed description of accesing the device for the first time. Step 1 Open the Internet Explorer (IE) browser and enter http://192.168.1.1.
  • Page 11 DSL-2730E User Manual...

  • Page 12: Setup

    DSL-2730E User Manual 3.2 Setup In the main interface, click Setup tab to enter the Setup menu as shown in the following figure. The submenus are Wizard, Local Network, Internet Setup, Wireless Setup and Time and Date. 3.2.1 Wizard Wizard enables fast and accurate configuration of Internet connection and other important parameters.
  • Page 13 DSL-2730E User Manual There are 5 steps to configure the device. Click Next to continue. Step 1 Change the device login password. Step 2 Set the time and date. Step 3 Configure the Internet connection.
  • Page 14 DSL-2730E User Manual If the internet service you subscribed is PPPoE or PPPoA, you can choose the Protocol to be PPPoE or PPPoA. Set the VPI and VCI. Enter the user name and password provided by your ISP.
  • Page 15 DSL-2730E User Manual If the internet service you subscribed is Dynamic IP, you can choose Protocol to be Dynamic IP. The page shown in the following figure appears. If the Protocol is Static IP, you can choose Protocol to be Static IP. The page shown in the following figure appears.
  • Page 16 DSL-2730E User Manual If the Protocol is Bridge, the page shown in the following figure appears.
  • Page 17 DSL-2730E User Manual Step 4 Configure the wireless network. Step 5 Complete and apply the settings. Click Apply to save the settings.

  • Page 18: Local Network

    DSL-2730E User Manual Note: In each step of the Wizard page, you can click Back to review or modify the previous settings. Click Cancel to exit the wizard page. 3.2.2 Local Network You can configure the LAN IP address according to the actual application. The preset IP address is 192.168.1.1.

  • Page 19: Lan Interface

    DSL-2730E User Manual 3.2.2.1 LAN Interface Choose Setup > Local Network > LAN Interface. The LAN Setting page shown in the following figure appears. You may configure the LAN interface, for example, the IP address and subnet mask.
  • Page 20 DSL-2730E User Manual The following table describes the parameters in this page. Field Description Enter the IP address of LAN interface. It is recommended to use an address from a block reserved for private use. This Address address block is 192.168.1.1- 192.168.1.254.
  • Page 21 DSL-2730E User Manual The following table describes the parameters of this page. Field Description Specify the LAN global ipv6 address. It can be Global Address assigned by ISP. Enable Enable or disable the Router Advertisement feature. Enable or disable the “Managed address M Flag configuration”...

  • Page 22: Dhcp Server

    DSL-2730E User Manual Field Description specifies the dhcpv6 server address pool and other parameters. “Auto”: dhcpv6 server is opened and it use WAN dhcp-pd prefix to generate address pool. 3.2.2.3 DHCP Server Choose Setup > Local Network > DHCP Server. The DHCP Server Setting page shown in the following figure appears.
  • Page 23 DSL-2730E User Manual Field Description operation systems that support the DHCP client. It specifies the first and last IP addresses in the IP IP Pool Range address pool. The router assigns IP address in the IP pool range to the host.
  • Page 24 DSL-2730E User Manual Description Field The MAC address is assigned at the factory and it consists of six pairs of hexadecimal character, for example, 00-A0-C5-00-02-12. It displays the lease time. The lease time determines Expiry the period that the host retains the assigned IP addresses before the IP addresses change.
  • Page 25 DSL-2730E User Manual In the DHCP Mode field, choose DHCP Relay. The page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field Description If set to DHCP Relay, the router acts a surrogate...
  • Page 26 DSL-2730E User Manual 3.2.2.4 DHCP Reserved Choose Setup > Local Network > DHCP Reserved. The DHCP Static IP Configuration page appears. This page lists the fixed IP/MAC address on your LAN. The device distributes the number configured to hosts on your network as they request Internet access.

  • Page 27: Internet Setup

    DSL-2730E User Manual 3.2.3 Internet Setup 3.2.3.1 Channel Config Choose Setup > Internet Setup > Channel Config. The Channel Configuration page appears. You may configure the parameters for the channel operation modes of your ADSL Router.
  • Page 28 DSL-2730E User Manual The following table describes the parameters of this page. Field Description Default Route You can select Auto or Specified. Selection The virtual path between two points in an ATM network, ranging from 0 to 255. The virtual channel between two points in an ATM...
  • Page 29 DSL-2730E User Manual Field Description user continuously, the router automatically disconnects the PPPoE connection. WAN IP Settings You can choose Fixed IP or DHCP.  If select Fixed IP, you should enter the local IP address, remote IP address and subnet mask.
  • Page 30 DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Protocol It displays the protocol type used for this WAN connection. ATM VCC The ATM virtual circuit connection assigned for this PPP interface (VPI/VCI).

  • Page 31: Atm Settings

    DSL-2730E User Manual Field Description PPPoE, or Disable Bridge. AC-Name The accessed equipment type. Service-Name The service name. 802.1q You can select Disable or Enable. After enable it, you need to enter the VLAN ID. The value ranges from 1 to 4095.

  • Page 32: Adsl Settings

    DSL-2730E User Manual The following table describes the parameters of this page. Field Description The virtual path identifier of the ATM PVC. The virtual channel identifier of the ATM PVC. The QoS category of the PVC. You can choose UBR, CBR, rt-VBR, or nrt-VBR.
  • Page 33 DSL-2730E User Manual 3.2.3.4 PVC Auto Search Choose Setup > Internet Setup > PVC Auto Search. The Auto PVC Configuration page appears. You may configure PVC auto detect function. Here you can add/delete auto PVC search table.

  • Page 34: Wireless Setup

    DSL-2730E User Manual 3.2.4 Wireless Setup This section describes the wireless LAN and basic configuration. A wireless LAN can be as simple as two computers with wireless LAN cards communicating in a pear-to-pear network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to wired LAN.
  • Page 35 DSL-2730E User Manual Description Field Choose the network model of the modem, which is Mode varied according to the software. By default, the network model of the modem is AP. The service set identification (SSID) is a unique name to identify the modem in the wireless LAN. Wireless...

  • Page 36: Wireless Security

    DSL-2730E User Manual Click the button Show Active Clients to view the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client. Click Apply Changes to save the settings. 3.2.4.2 Wireless Security Choose Setup > Wireless Setup > Wireless Security. The Wireless Security Settings page appears.
  • Page 37 DSL-2730E User Manual The following table describes the parameters of this page: Field Description Configure the wireless encryption mode. You can choose None, WEP, WPA (TKIP), WPA (AES), WPA2 (AES), WPA2 (TKIP) or WPA2 Mixed.  Wired equivalent privacy (WEP) encrypts data frames before transmitting over the wireless network.
  • Page 38 DSL-2730E User Manual The following describes the parameters of this page: Field Description Choose the WEP key length. You can Choose Key Length 64-bit or 128-bit.  If you choose 64-bit, you can choose ASCII (5 characters) or Hex (10 characters).

  • Page 39: Time And Date

    DSL-2730E User Manual Field Description characters), enter any 13 ASCII characters.  If you choose 128-bit and Hex (26 characters), enter any 26 hexadecimal characters. Click it to apply the settings temporarily. If you want Apply Changes to save the settings of this page permanently, click Save in the lower left corner.

  • Page 40: Advanced

    DSL-2730E User Manual Description Field Time Zone Select your local time zone from the dropdown list. Daylight Adjust the clock for daylight savings time. To synchronize the time automatically with the Internet or your own computer, you may select Set Time...

  • Page 41: Advanced Wireless

    DSL-2730E User Manual 3.3.1 Advanced Wireless This function is used to modify the standard 802.11g wireless radio settings. It is suggested not to change the defaults, as incorrect settings may reduce the performance of your wireless radio. The default settings provide the best wireless radio performance in most environments.

  • Page 42: Access Control

    DSL-2730E User Manual Description Field RTS Threshold Determines the packet size of a transmission through (Request to the use of the router to help control traffic flow. Send Threshold) A packet of information that is sent from a connected device to all other devices where it announces its Beacon Interval availability and readiness.
  • Page 43 DSL-2730E User Manual Set the Wireless Access Control Mode to Allow Listed to enable white list function. Only the devices whose MAC addresses are listed in the Current Access Control List can access the modem. Set the Wireless Access Control Mode to Deny Listed to enable black list function.
  • Page 44 DSL-2730E User Manual There are two methods for the wireless client to establish connection with the modem through WPS. For one method, click Regenerate PIN to generate a new PIN, and then click Start PBC. In the wireless client tool, enter the PIN which is generated by the modem to start connection.
  • Page 45 DSL-2730E User Manual 3.3.1.4 MBSSID Choose Advanced > Advanced Wireless > MBSSID. The page shown in the following figure appears. In this page, you can set virutal access points (VAP), its SSID and authentication type. The device supports four virtual access points (VAPs). It is a unique name to identify the modem in the wireless LAN.

  • Page 46: Access Control List

    DSL-2730E User Manual 3.3.2 Access Control List Multiple connections are required by some applications, for example, internet games, video conferencing and Internet telephony. These applications have difficulties working through NAT (Network Address Translation). This section is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on your network.
  • Page 47 DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Select the router interface. You can select LAN or Direction Select WAN. In this example, LAN is selected. LAN ACL Switch Select it to enable or disable ACL function.
  • Page 48 DSL-2730E User Manual Field Description to the Current ACL Table. Reset Click it to refresh this page. When the direction of data packets is set to WAN, the page shown in the following figure appears. The following table describes the parameters and buttons of this page:...

  • Page 49: Port Triggering

    DSL-2730E User Manual Field Description You can choose the following services from WAN: Services Allowed Web, Telnet, SSH, TFTP, SNMP and PING. You can also choose all the services. After setting the parameters, click it to add an entry to the Current ACL Table.
  • Page 50 DSL-2730E User Manual Click the Usual Application Name drop-down menu to choose the application you want to set up for port triggering. When you have chosen an application the default Trigger settings will populate the table below. If the application you want to set up isn’t listed, click the User-defined Application Name radio button and type in a name for the trigger in the Custom application field.

  • Page 51: Port Forwarding

    DSL-2730E User Manual 3.3.4 Port Forwarding This function is used to open ports in your device and redirect data through those ports to a single PC on your network (WAN-to-LAN traffic). It allows remote users to access services on your LAN, such as FTP for file transfers or SMTP and POP3 for e-mail.

  • Page 52: Dmz

    DSL-2730E User Manual 3.3.5 DMZ is the abbreviation of the Demilitarized Zone. Since some applications are not compatible with NAT, the device supports the use of a DMZ IP address for a single host on the LAN. This IP address is not protected by NAT and it is visible to agents on the Internet with the correct type of software.

  • Page 53: Url Block

    DSL-2730E User Manual 3.3.6.1 URL Block Choose Advanced > Parental Control > URL Block. The URL Block page shown in the following figure appears. You may deny certain websites from being accessed during the "schedule" you specified. Here you can add/delete filtered URL.
  • Page 54 DSL-2730E User Manual 3.3.6.2 MAC Block Choose Advanced > Parental Control > MAC Block. The URL Block page shown in the following figure appears. You may block a LAN device connected to the router in the specified time section. In the field Rule Name, input a name that is meaningful to you, then enter a MAC address that you want to deny access to the Internet, and set the days and hours, and click Add Rule to add the MAC into the MAC Blocking Table.

  • Page 55: Filtering Options

    DSL-2730E User Manual In the field Rule Name, give the schedule a name that is meaningful to you, such as "Weekday rule". Set the Day(s) and time field, and click Add Rules to save the new rule in the following Rules Table.
  • Page 56 DSL-2730E User Manual Direction Upstream (Downstream) means packets outgoing (incoming) from (to) router. The Source IP addresses are LAN-side (WAN-side) addresses and the Destination IP addresses are WAN-side (LAN-side) addresses. Select the rule action, specify at least one of the following criteria: protocol, source/destination IP address, subnet mask and source/destination port.

  • Page 57: Mac Filter

    DSL-2730E User Manual For detailed configuration, you may refer to 3.3.7.1IP/Port Filter. 3.3.7.3 MAC Filter Choose Advanced > Filtering Options > MAC Filter. The MAC Filtering page shown in the following figure appears. You may create a list of MAC addresses...

  • Page 58: Dos Settings

    DSL-2730E User Manual 3.3.8 DoS Settings Denial-of-Service Attack (DoS attack) is a type of attack on a network that is designed to bring the network to its knees by flooding it with useless traffic. Choose Advanced > DoS Settings. The DOS Settings page shown in the following figure appears.

  • Page 59: Dns

    DSL-2730E User Manual 3.3.9 Domain Name System (DNS) is an Internet service that translates the URL/domain name into the corresponding IP address. Since URL/Domain Names are alphabetical, they are easier to remember. But the Internet is based on IP address. For example, the URL/Domain Name www.dlink.com is actually 192.168.0.123.

  • Page 60: Ipv6 Dns

    DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Select it, the router accepts the first received DNS Attain DNS assignment from one of the PPPoA, PPPoE or MER Automatically enabled PVC(s) during the connection establishment.

  • Page 61: Dynamic Dns

    DSL-2730E User Manual The following table describes the parameters and buttons of this page. Field Description Select it, the router accepts the first received DNS Attain DNS assignment from one of the PPPoA, PPPoE or MER Automatically enabled PVC(s) during the connection establishment.
  • Page 62 DSL-2730E User Manual be set up with one of the supported DDNS service providers (DyndDNS.org or dlinkddns.com). Choose Advanced > Dynamic DNS. The Dynamic DNS Configuration page shown in the following page appears. The following table describes the parameters and buttons of this page.

  • Page 63: Network Tools

    DSL-2730E User Manual Click Add to save the settings to the Dynamic DDNS Table. 3.3.11 Network Tools The router provides following tools: Port Mapping, IGMP Proxy, IP QoS, UPnP, SNMP, TR-069, Software Forbidden, ARP Binding and Client Limit. 3.3.11.1 Port Mapping Port Mapping supports a single (LAN) port or multiple (LAN) ports to be formed as a group and mapped to a PVC (which is associated w/ a VLAN).
  • Page 64 DSL-2730E User Manual Follow the steps to manipulate a mapping group. Step 1 Select a group from the table. Step 2 Select interfaces from the available WAN and LAN interface groups and add it to the interface group list using the arrow buttons to manipulate the required mapping of the ports.
  • Page 65 DSL-2730E User Manual The selected interfaces will be removed from their existing groups and added to the new group. 3.3.11.2 IGMP Proxy IGMP allows support for efficient multicasting -- transmission of identical content, such as multimedia, from a source to a number of recipients. IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces.
  • Page 66 DSL-2730E User Manual Field Description The device sends query messages to check IGMP user Query Interval periodically. The unit is second. Query The device waits for the IGMP user’s reply. The unit is Response 100 * millisecond. Interval The duration for the modem to cease forwarding Group Leave multicast packets after a corresponding IGMP "Leave...
  • Page 67 DSL-2730E User Manual Step 1 Enable IP QoS and click Apply to enable IP QoS function. Step 2 Click add rule to add a new IP QoS rule. The page shown in the following figure appears. The following table describes the parameters and buttons of this page.
  • Page 68 DSL-2730E User Manual Field Description QoS Policy You can choose stream based, 802.1p based, or DSCP based. Schedule Mode You can choose strict prior or WFQ (4:3:2:1). Source IP The IP address of the source data packet. Source Mask The subnet mask of the source IP address.
  • Page 69 DSL-2730E User Manual 3.3.11.5 SNMP SNMP (Simple Network Management Protocol) provides a means to monitor status and performance and set configuration parameters. It enables a management station to configure, monitor and receive trap messages from network devices. Choose Advanced > Network Tools > SNMP. The SNMP Protocol Configuration page shown in the following figure appears.
  • Page 70 DSL-2730E User Manual Description Field Select it to enable SNMP function. You need to Enable SNMP enable SNMP, and then you can configure the parameters of this page. Enter the trap IP address. The trap information is Trap IP Address sent to the corresponding host.
  • Page 71 DSL-2730E User Manual The following table describes the parameters of this page: Field Description ACS Configuration The URL of the auto-configuration server to connect to. User Name The user name for logging in to the ACS.
  • Page 72 DSL-2730E User Manual Field Description Password The password for logging in to the ACS. Periodic Inform Enable Select Enable to periodically connect to the ACS to check configuration updates. Periodic Inform Specify the amount of time between Interval connections to ACS.
  • Page 73 DSL-2730E User Manual 3.3.11.7 Software Forbidden Choose Advanced > Network Tools > Software Forbidden. The Software Forbidden page shown in the following figure appears. You may config some software to be forbidden to deny the ip packets of it. To forbid one specified PC (or some PCs) from using an application, select the application you want to prohibit, and input a single IP address or IP addresses in range.

  • Page 74: Client Limit

    DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description An IP address to be bound. IP Address Mac Address An MAC address to be bound. Click this icon to add an ARP binding.

  • Page 75: Routing

    DSL-2730E User Manual 3.3.12 Routing Under this menu, static route, default gateway and RIP type routing configurations can be performed. 3.3.12.1 Static Route Choose Advanced > Routing > Static Route. The Routing Configuration page shown in the following figure appears. This page is used to configure the routing information.
  • Page 76 DSL-2730E User Manual Field Description Enable Select it to use static IP routes. Destination Enter the IP address of the destination device. Subnet Mask Enter the subnet mask of the destination device. Next Hop Enter the IP address of the next hop in the IP route to the destination device.
  • Page 77 DSL-2730E User Manual 3.3.12.2 IPv6 Static Route Choose Advanced > Routing > IPv6 Static Route. The IPv6 Routing Configuration page shown in the following figure appears. This page is used to configure the routing information. You can add or delete IP routes.
  • Page 78 DSL-2730E User Manual Choose Advanced > Routing > IPv6 Static Route. The IPv6 Routing Configuration page shown in the following figure appears. The following table describes the parameters and buttons of this page: Field Description Select Enable, the router communicates with other RIP-enabled devices.

  • Page 79: Nat

    DSL-2730E User Manual Field Description Click it to add the RIP interface to the Rip Config List. Delete Select a row in the Rip Config List and click it to delete the row. 3.3.13 NAT Under this menu, NAT ALG (Application Layer Gateway), NAT Exclude IP, NAT Forwarding, FTP ALG Config and NAT IP Mapping can be performed.
  • Page 80 DSL-2730E User Manual 3.3.13.3 NAT Forwarding Choose Advanced > NAT > NAT Forwarding. The NAT Forwarding page shown in the following figure appears. Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway's NAT firewall.
  • Page 81 DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Input a local IP address. Local IP Address Remote Input a remote IP address Address Enable Enable the current configured rule. Apply Changes Submit the configurations.
  • Page 82 DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description FTP ALG port Set an FTP ALG port. Add Dest Ports Add a port configuration. Delete Selected Delete a selected port configuration from the list.

  • Page 83: Maintenance

    DSL-2730E User Manual 3.4 Maintenance 3.4.1 System Choose Maintenance > System. The page shown in the following figure appears. In this page you can reboot your router or save your router configuration to a file on your computer in case you have to reset your router to factory default settings.
  • Page 84 DSL-2730E User Manual The following table describes the parameters and buttons of this page: Field Description Reset to default This option restores all configuration settings back to the settings that were in effect at the time the router was shipped from the factory. All settings will be lost.

  • Page 85: Firmware Update

    Choose Maintenance > Firmware Update. The page shown in the following figure appears. This page displays your device firmware version and information that will be helpfulfor D-Link technicians should you require any technical support. The procedure for updating the firmware is as follows.

  • Page 86: Diagnostics

    DSL-2730E User Manual password, the only solution is to reset your router to factory default settings and you will lose all your device configuration settings. The following table describes the parameters and buttons of this page: Field Description Root The root account is fixed, having full access to the Web-based management interface.
  • Page 87 DSL-2730E User Manual The following table describes the parameter and button of this page: Field Description Host Enter the valid IP address or domain name. Ping Click it to start to Ping. 3.4.4.2 Ping6 Choose Maintenance > Diagnostics > Ping6.
  • Page 88 DSL-2730E User Manual The following table describes the parameters and buttons of this page. Field Description Host Enter the destination host address for diagnosis. NumberOfTries Number of repetitions. Timeout Put in the timeout value. Datasize Packet size. DSCP Differentiated Services Code Point, You should set a value between 0-63.

  • Page 89: System Log

    DSL-2730E User Manual Click Start to start ADSL tone diagnostics. 3.4.4.5 Diag Test Choose Maintenance > Diagnostics > Diag Test. The page shown in the following figure appears. In this page, you can test the DSL connection. You can also view the LAN status connection and ADSL connection.
  • Page 90 DSL-2730E User Manual The router can only keep a limited number of log entries due to router memory constraints. If you have an external SYSLOG server, you may choose to configure external logging and all log entries will be sent to your remote server.

  • Page 91: Logout

    DSL-2730E User Manual 3.4.6 Logout Choose Maintenance > Logout. The page shown in the following figure appears. In this page, you can log out of the configuration page. 3.5 Status You can view the system information and monitor performance 3.5.1 Device Info Choose Status >...
  • Page 92 DSL-2730E User Manual...

  • Page 93: Wireless Clients

    DSL-2730E User Manual 3.5.2 Wireless Clients Choose Status > Wireless Clients. The page shown in the following figure appears. This table shows the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client. 3.5.3 DHCP Clients Choose Status >...

  • Page 94: Adsl Driver

    DSL-2730E User Manual 3.5.4 ADSL Driver Choose Status > ADSL Driver. The page shown in the following page appears. This page displays all ADSL statistics information, including link down or on, downstream and upstream, type, line coding and so on.

  • Page 95: Route Info

    DSL-2730E User Manual 3.5.6 Route Info Choose Status > Route Info. The page shown in the following page appears. This table shows a list of destination routes commonly accessed by your network.

  • Page 96: Help

    DSL-2730E User Manual 3.6 Help In the main interface, click Help tab to enter the Help menu as shown in the following figure. This section provides detailed configuration information for the device. Click a link to view corresponding information.

Table of Contents