Related Manuals for German Light Products impression X4S
Summary of Contents for German Light Products impression X4S
- Page 1 from software version: V1.09 (Instruction version: 1.1) e-mail: service@glp.de Internet: http://www.glp.de...
- Page 2 Notes: German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
-
Page 3: Table Of Contents
S ..........16 5.1 Safety regulations ..................16 5.2 Maintenance and Interval (rule-of-thumb) ............16 5.3 Changing the Fuse..................17 Technical Specifications..................18 Dimensions ......................19 Index ........................20 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 4: Description Of Device
1 6. Power On/Off 7. DMX- Output (5-pin) 8. DMX- Input (5-pin) 9. Mains supply (fixed cable) b a s e s i d e 2 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 5: Safety Instructions
9. Use only original GLP spare parts. Any structural modification of the system will terminate all warranty claims. 10. Please keep this instruction manual for future reference. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 6: Preparation And Installation
Should you have any questions about the operation of your fixture then please contact your local GLP office, or their authorized distributor, a list of which can be found at http://www.glp.de. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 7: Mounting
In (length max.11mm) addition the top of the base is marked with a FRONT arrow allowing consistent orientation during installation. 4x rubber feet Fixture from below German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 8: Operating On The Floor (Upright)
This technique is necessary to cope with the torque which accrues in this mounting position. Never use the "Mounting in hanging position" technique described above to fasten the fixture in the sideways position. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 9: Securing The Fixture
USITT DMX-512 Standard input/output in 5-pin connectors. Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] / Pin 4&5 N.C. The DMX- Addressing starts at the DMX- Address [001]. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 10: The Menu Field
White adjust Adjust intensity for red channel White adjust Adjust intensity for blue channel blue White adjust Adjust intensity for green channel green Clear Erase EEPROM memory EEPROM German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... - Page 11 4 below Position Switch automatic position feedback ON/OFF feedback Reverse Pan Invert Pan movements: ON/OFF Reverse Tilt Invert Tilt movements: ON/OFF Reset RESET and new calibration for all functions German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
-
Page 12: Dmx Channel Selection (Dmx Protocol)
00..03 0..1 Change PWM frequency 100..200 64..C8 40..78 RESET 250..255 FA..FF 98..100 14) Move- No macros ment Movement Size Phase Use "Speed" to adjust macros 0° 01..01 01..01 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... - Page 13 Color 05 - Green 40..47 28..2F 16..18.5 Color 06 - Turquoise 48..55 30..37 19..21.5 Color 07 - Cyan 56..63 38..3F 22..24.5 Color 08 - Blue 64..71 40..47 25..27.5 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
- Page 14 0..255 00..FF 0..100 5) Red- Color mixing system – Red 0 - 100% 0..255 00..FF 0..100 coarse 6) Red- Color mixing system – Red-Low 0..255 00..FF 0..100 fine German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
- Page 15 Rainbow-effect Stop will pause this function. After resuming the rainbow-effect will be continued from the current color. The Rainbow-effect will run synchronously only if started from one of the predefined colors (see also before). German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
-
Page 16: Maintaining And Cleaning The
The intervals given below are only suggestions from our experience. Position Interval In this way LED reflector and optical system weekly soft brush /lint-free cloth Fan and air channel monthly vacuum cleaner, airbrush, etc. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 17: Changing The Fuse
Replace the fuse with one with the exact rating as printed in this manual or the body of the fixture. Never use a different one! Attach the side cover again before operating the fixture. German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 18: Technical Specifications
300° in min. 1,5 seconds (Position Feedback) Weights and Measures ∅165,5 mm Base only Total width of fixture 224 mm Hight (head vertical) 323mm (incl. base) Weight (net) 5.5 kg German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 19: Dimensions
7 Dimensions 3x M10 (length max.11mm) German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... -
Page 20: Index
VBG 70 ............7 Menu Field ..........10 Micro-fuse ............. 9 Mode-key ..........10 Warranty claims ..........5 Mounting............7 Weights and Measures........ 18 Mounting in hanging Position......8 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09... - Page 21 German Light Products GmbH (Instruction version: 1.1) / from software version: V1.09...
Need help?
Do you have a question about the impression X4S and is the answer not in the manual?
Questions and answers