Table of Contents
Advertisement
UD-Stomp
Table1
ITEM
1
INPUT Sensitivity
2
INPUT Sensitivity
3
INPUT Sensitivity
4
INPUT Sensitivity
5
INPUT Sensitivity
6
INPUT Sensitivity
7
INPUT Sensitivity
8
INPUT Sensitivity
9
INPUT Sensitivity
10
INPUT Sensitivity
11
INPUT Sensitivity
12
INPUT Sensitivity
13
INPUT Sensitivity
14
INPUT Sensitivity
15
INPUT Sensitivity
16
NOISE LEVEL
17
NOISE LEVEL
18
NOISE LEVEL
19
NOISE LEVEL
20
DISTORTION FACTOR
21
DISTORTION FACTOR
22
DISTORTION FACTOR
23
DISTORTION FACTOR
24
INPUT Sensitivity
F.
CHEKING OF THE ROM VERSION
While pressing the DOWN and UTILITY switches, turn
on the POWER switch. The model name "Ud.S" is
ERROR MESSAGES
If an error occurs during operation, one of the following error message numbers will appear in the display.
Stop operation of the device and follow the proper solution described below.
E 1
: MIDI Receive Buffer Full
CAUSE:
SOLUTION: Try reducing the amount of data being sent or, break the data into smaller blocks.
E 2
: Communication Error.
CAUSE:
SOLUTION: Check all connections, etc. and try again.
E 3
: Bulk Receive Check Sum Error.
CAUSE:
SOLUTION: Check all connections and data, and try again.
E 4
: Bulk Receive Data Abnormality.
CAUSE:
SOLUTION: Check all connections and data, and try again.
E 5
: Backup Battery Error.
CAUSE:
SOLUTION: Continued use of the device will result in the loss of data.
28
JK101(INPUT) -5dBm(1KHz)
JK101(INPUT) -5dBm(10KHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10KHz)
JK101(INPUT) -25dBm(1KHz)
JK101(INPUT) -5dBm(1KHz)
JK101(INPUT) -5dBm(10KHz)
JK101(INPUT) -5dBm(100Hz)
JK101(INPUT) -25dBm(100Hz)
JK101(INPUT) -25dBm(10KHz)
JK101(INPUT) -25dBm(1KHz)
JK101(INPUT) -35dBm(1KHz) HIGH/LOW SW ON
JK101(INPUT) -35dBm(10KHz) HIGH/LOW SW ON
JK101(INPUT) -35dBm(100Hz) HIGH/LOW SW ON after operation OFF
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
Disconnect the jack of JK101 (INPUT), without filter
JK101(INPUT) -5dBm (1KHz)
JK101(INPUT) -25dBm (1KHz)
JK101(INPUT) -5dBm (1KHz)
JK101(INPUT) -25dBm (1KHz)
JK101(INPUT) -15dBm (1KHz)
Too much MIDI data is being received at one time.
An abnormality is detected during MIDI communications.
The check sum does not match the received MIDI bulk data.
An abnormality is detected in the received MIDI bulk data.
Backup battery power is depleted.
INPUT
JK103(OUT L/MONO)+1.0dBm ± 3dB
JK103(OUT L/MONO)+1.0dBm ± 3dB
JK103(OUT L/MONO)+1.0dBm ± 3dB
JK104(OUT R)-1.0dBm ± 3dB
JK104(OUT R)-1.0dBm ± 3dB
JK104(OUT R)-1.0dBm ± 3dB
JK102(HP L)-0.5dBm ± 3dB
JK102(HP L)-0.5dBm ± 3dB
JK102(HP L)-1.5dBm ± 3dB
JK102(HP R)-3.5dBm ± 3dB
JK102(HP R)-2.5dBm ± 3dB
JK102(HP R)-2.5dBm ± 3dB
JK104(OUT R)-0.5dBm ± 3dB
JK104(OUT R)-0.5dBm ± 3dB
JK104(OUT R)-0.5dBm ± 3dB
JK103(OUT L/MONO)-45dBm or less
JK104(OUT R)-45dBm or less
JK102(HP L)-45dBm or less
JK102(HP R)-45dBm or less
JK103(OUT L/MONO) 0.5% or less
JK104(OUT R) 0.5% or less
JK102(HP L) 0.5% or less
JK102(HP R) 0.5% or less
JK2(Digital Out) Lch:-18dBm ± 3dB, Rch: ± 0dBm ± 3dB
displayed for about 2 seconds. As the version number
"1.00" (each * representing a number) appears after that,
check it. Then the mode will return to the normal mode.
OUTPUT
Advertisement
Table of Contents
