Related Manuals for Aurora DXW-2
Summary of Contents for Aurora DXW-2
- Page 1 USERS GUIDE DXW-2 Series 2 Gang Decora ® HDBaseT Wall Plate Transmitter DXW-2 DXW-2E DXW-2EU / DXW-2EUH Manual Number: 131120 Firmware: v1.13 & above...
-
Page 2: Safety Instructions
Power outlet: To prevent electric shock, be sure the electrical plug used on the product power cord matches the electrical outlet used to supply power to the Aurora product. Use only the power adapter and power connection cables designed for this unit. -
Page 3: Table Of Contents
Front DXW-2, DXW-2E, DXW-2EU, DXW-2EUH ................. 3 Rear Panel DXW-2, DXW-2E, DXW-2EU, DXW-2EUH ............... 4 APPLICATIONS ......................... 5 Example 1 Typical DXW-2 Transmitter to RX Receiver ................ 5 Example 2 DXB-8 Button Wall Control to DXW-2................. 6 Example 3 DXW-2EU Connected to DXE-USB-H1 ................7 Example 4 DXW-2EUH Connected to DXE-USB-D1P ................. -
Page 4: Package Contents
DXE-USB-D1P USB Device side extender unit with 24v DC power supply for DXW-2EUH Compatible HDBaseT Receivers The DXW-2 Series is an HDBaseT technology product and should work with other HDBaseT receivers. Please note if product does not supply POE remotely local 24v DC power supply (PS0053-1) must be used. -
Page 5: Introduction
USB ports for powering USB devices and transmitting 480Mbps up to 220ft independently to a different location. The DXW-2 Series can be remotely powered by the receiver device and also has the ability to transmit IR signals via the sensor window on the front of the unit for remote control of IR controllable devices. -
Page 6: Front Dxw-2, Dxw-2E, Dxw-2Eu, Dxw-2Euh
DB15 VGA Connector – VGA up to 1080p can be input. Through the use of a breakout cable YPbPr, Video, and S-Video can also be input. The DXW-2 will check for VGA signal, if no signal, YPbPr, then Composite Video, and finally S-Video. When switching back and forth the DXW-2 will remember the last source selected for faster switching. -
Page 7: Rear Panel Dxw-2, Dxw-2E, Dxw-2Eu, Dxw-2Euh
220 feet with CAT 6 cable allowing the PC to be located elsewhere from the video. Note: Some 2 gang electrical boxes or mud rings have curved or beveled corners that may prevent the DXW-2 from properly fitting. Make certain to use a brand that fits the full dimensions listed in the specification section. -
Page 8: Applications
User Guide APPLICATIONS Example 1 Typical DXW-2 Transmitter to RX Receiver... -
Page 9: Example 2 Dxb-8 Button Wall Control To Dxw-2
DXW-2 to the DXE-CAT-RX receivers. This allows not only the switching of the DXW-2 to be controlled but the remote display device as well. Make certain the baud rates are set the same on the DXW-2 and the DXB-8. More information on the DXB-8 can be found on the Aurora website... -
Page 10: Example 3 Dxw-2Eu Connected To Dxe-Usb-H1
User Guide Example 3 DXW-2EU Connected to DXE-USB-H1 The DXE-USB-H1 (Host Unit) will be located by the computer using the Mini USB Type B to USB Type A Male cable that is supplied with the DXE-USB-H1. The 24v DC is not required to be connected when used with the DXW-2EU. -
Page 11: Example 4 Dxw-2Euh Connected To Dxe-Usb-D1P
User Guide Example 4 DXW-2EUH Connected to DXE-USB-D1P The DXE-USB-D1P (Device Unit with 24v DC supply) will be located by the product using the USB Type A connectors (ex. Keyboard, mouse, etc). The DXW-2EUH will supply 5v to the USB connectors for local charging even if the DXE-USB-D1P is not connected as it derives its power from the HDBaseT connection. -
Page 12: Operation
The time to lock depends on the display but typical time can be from 3-5 seconds. Keep in mind the DXW-2 series does not scale so what comes in is what will go back out for both the VGA and the HDMI. -
Page 13: Edid Handling
HDMI input on the display or amplifier. Keep in mind if this feature is enabled (see RS-232 commands) installations relying on loss of signal to turn display on and off will not work. The DXW-2 factory default is disabled but can be enabled and saved in non-volatile memory via RS-232 command. -
Page 14: Serial Commands
User Guide SERIAL COMMANDS RS-232 Commands ! - Command, ? - Query, ~ Response <cr> = 0x0D Hex / 13 Decimal Command String Format Information y = port number = 1 or 2 (1 is HDBaseT, 2 is Rear Port) a = baud rate = 2400, 4800, 9600, 19200, 38400, 57600, 115200 Baud Rate Setup... -
Page 15: Rs-232 Command Usage
User Guide RS-232 Command Usage Example Example String Example Response Set Port 1 Baud Rate to 96008N1. Baud Rate Setup Command !BR1,9600,8N1<cr> ~BR1,9600,8N1<cr> Set button 1 to Release to green & Push to blue. Button LED Setup !BL1,G,B<CR> ~BL1,G,B<CR> Trigger button 2 (HDMI) Button Push !BP2<cr>... -
Page 16: Connector Pin Definition
User Guide CONNECTOR PIN DEFINITION VGA DB15HD Pin 1 Red (Pr) Pin 8 Ground Pin 15 SCL Pin 2 Green (Y, S-Video C) Pin 9 Pin 3 Blue (Pb) Pin 10 SYNC Ground Pin 11 NC Pin 4 Composite (S-Video Y) Pin 5 Ground Pin 12 SDA Pin 6 Ground... -
Page 17: Cat5E/6/6A
User Guide CAT5e/6/6A All transmission distances are measured using Belden 1583A CAT5e 125MHz Solid UTP cable. The transmission distance is defined as the distance between the video source and the display. To reduce the interference among the unshielded twisted pairs of wires in UTP cable, you can use shielded STP cables to improve EMI problems, which is worsen in long transmission. -
Page 18: Appendix
Problem Solution a. Check that the power plug is properly inserted into a functioning power outlet. Keep in mind the DXW-2 can be powered locally or remotely via 1. No Video Signal. HDBaseT POE. b. Make certain source is on. -
Page 19: Appendix 2 Firmware Update
DXW-2 Update Utility DXW-2 Update Software requires a serial cable connected in a null (RX to TX, TX to RX, GND to GND) configuration to a PC. The firmware can be updated directly at the DXW-2 rear serial port or it can be updated via HDBaseT receiver RS-232 port. -
Page 20: Appendix 3 Supported Timing
User Guide APPENDIX 3 Supported Timing VGA Port Supported Timing 525p@60 640x480@60 1152x864@75 625p@50 640x350@70 1280x768@60 720p@60 640x350@85 1280x800@60 720p@50 640x480@72.80 1280x960@60 720p@24 640x480@75 1280x960@85 720p@25 640x480@85 1280x1024@60.02 720p@30 720x400@70 1280x1024@75.02 1080i@60 720x400@85 1280x1024@85.02 1080i@50 800x600@56.25 1360*768@60 1080i@100 800x600@60.31 1440x900@60 1080p@60 800x600@72.19 1400x1050@60... -
Page 21: Appendix 4
24 .65A DC (Only 1 required on either TX or RX) DXW-2 & DXW-2E 6 Watts [max], DXW-2EU / 2EUH 11Watts (5 Watts for USB Ports) Important: If DXW-2EU is drawing power from the receiver it will require 20 watt or Power consumption better power supply. - Page 22 User Guide 1x DXW-2 or DXW-2E or DXW-2EU / 2EUH accordingly Package Contents 1x Paintable White Wall Plate 1x User Manual PS0053-1 24v DC 15.5 Watt power Supply Options PS0062-1 24v DC 24 Watt power Supply CA0054-1 8” VGA to 4 RCA Adaptor cable (YPbPr and Composite Video)
-
Page 23: Appendix 5 Cabling
APPENDIX 5 Cabling Aurora extender products have been tested utilizing shielded cabling. Although our products will work fine without shielded cable it is highly recommended for environmental reasons as the signals are high frequency and can radiate as well as be susceptible to external frequencies and possibly cause noise or disruption in the image. -
Page 24: Appendix 6 Warranty
Limited 3 Year Warranty Aurora Multimedia Corp. (“Manufacturer”) warrants that this product is free of defects in both materials and workmanship for a period of 3 years as defined herein for parts and labor from date of purchase. This Limited Warranty covers products purchased in the year of 2009 and after. - Page 25 User Guide This product warranty extends to the original purchaser only and will be null and void upon any assignment or Aurora Multimedia Corp. 205 Commercial Court Morganville, NJ 07751 Phone: 732-591-5800 Fax: 732-591-6801...
Need help?
Do you have a question about the DXW-2 and is the answer not in the manual?
Questions and answers