HG532e Home Gateway User Guide HUAWEI TECHNOLOGIES CO., LTD.
Page 2
HG532e Home Gateway V100R001 User Guide 202494_03 Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address: Huawei Industrial Base Bantian, Longgang...
Page 3
Huawei Technologies Co., Ltd. and its affiliates ("Huawei"). The product described in this manual may include copyrighted software of Huawei and possible licensors. Customers shall not in any manner reproduce, distribute, modify, decompile, disassemble, decrypt, extract, reverse engineer, lease, assign, or sublicense the said software, unless such restrictions are prohibited by applicable laws or such actions are approved by respective copyright holders.
Page 4
To better understand how we protect your personal information, please see the privacy policy at http://consumer.huawei.com/privacy-policy. ErP Product Information Hereby, Huawei Technologies Co.,Ltd. declares that the product meets the directive 2009/125/EC and its implementation regulation (EC) NO 1275/2008 amended by (EC) 278/2009,(EC) 642/2009,(EU) 617/2013,(EU) 801/2013,and its implementation regulation (EC) NO 278/2009.
Contents 1 Connecting the Cables and Getting Started ........1 1.1 Connecting Cables ................ 1 1.2 Powering On the HG532e .............. 2 2 Setting Network Access Parameters ..........3 2.1 Logging in to the Web-based Configuration Utility ......3 2.2 Configuring a Dial-up Connection to Access the Internet ....4 2.3 Configuring a Wireless Network Name and Password ......
HG532e). 1.1 Connecting Cables The following figure shows an example of how to connect the cables. In this example, the HG532e is connected to a desktop computer, a laptop computer, and a telephone. 1. Power adapter 2. Desktop computer 3.
40 seconds to 3 minutes. When the ADSL indicator stops blinking and remains on, the HG532e is working correctly. To power off the HG532e, press the On/Off button on the side panel, and then unplug the power adapter.
2.1 Logging in to the Web-based Configuration Utility Most parameters of the HG532e are preset before delivery to meet common application scenarios at homes. To check the HG532e's working status or to configure certain advanced network functions, use the web-based configuration utility.
2.2 Configuring a Dial-up Connection to Access the Internet The HG532e works in PPP mode by default. The HG532e starts to set up a dial-up connection automatically after starting up, meaning you do not need to install dial-up software or perform dial-up operations on your computer.
For details, see the installation guide provided by the vendor of your wireless adapter. The wireless network function is enabled on the HG532e before delivery. To check the function status, see section 4.2 "Enabling or Disabling the Wireless Network Function."...
Step 2 Within 2 minutes, enable the WPS negotiation function on the computer. Wait for a while. The WPS indicator of the HG532e stops blinking and remains on, indicating that a wireless connection is set up between the HG532e and the computer.
Page 12
5. Click OK to close the dialog box, and then close the Computer Management window. Step 2 Find the wireless network name (SSID) and its password (WLAN Key) printed on the label on the HG532e's rear panel. If the default wirless network name and password have been changed, use the new values.
Page 13
You need to set up a wireless connection only once. Then you can access the wireless network anytime you want as long as that the wireless network name and password are not changed. When the HG532e is working properly, your computer connects to the HG532e automatically after its wireless function is enabled.
If you forget the password, you can restore the default settings by pressing and holding the Reset button on the rear panel of the HG532e for over 6 seconds. The user name and password used for logging in to the web-based configuration utility are then restored to their default values.
There are two methods for enabling or disabling the wireless network function. Using the WLAN Button To enable or disable the wireless network function, press the WLAN button on the side panel of the HG532e. The WLAN indicator indicates the status of the wireless network function. Using the Web-based Configuration Utility...
You must remember the wireless network name and password you set. You will be prompted to enter this password when connecting wireless devices, such as a computer, to the HG532e's wireless network. Connection to the HG532e's wireless network fails if you enter an incorrect password.
Reset button on the rear panel for over 6 seconds, and then release the button. You can also do the following to restore the HG532e to its default settings from the web-based configuration utility: Step 1 Log in to the web-based configuration utility.
How can I quickly restore the HG532e to its default settings? To restore the HG532e to its default settings, press and hold the Reset button on the HG532e's rear panel for over 6 seconds when the HG532e is powered on, and then release the button.
Page 19
If the LAN indicator is off, perform further checks as follows: 1. Check that the network adapter on your computer is enabled. 2. Check that the network cable between the HG532e and the computer is securely connected. Remove and then insert the network cable or replace the network cable when necessary.
Page 20
If the dial-up connection fails, perform further checks as follows: 1. Close the PPP dial-up software, and power off the HG532e. After 5 minutes, power on the HG532e, and use the PPP dial-up software to dial again. 2. Restore the HG532e to its default settings.
Page 21
If the problem persists, restore the HG532e to its default settings. For details, see "How can I quickly restore the HG532e to its default settings?" What can I do if I cannot access the Internet over a wireless connection? Step 1 Check that all cables are securely connected, such as the power adapter cable and the telephone line.
Page 22
Step 8 Check that you can use the PPP dial-up software to set up dial-up connection. Step 9 Try to access more websites to check whether the HG532e can access these websites. If you still cannot access the websites, restore the HG532e to its default settings.
Page 23
SSID is set to SSID1. It is recommended that you set the security mode to WPA-PSK/WPA2-PSK. What can I do if I cannot set up a wireless connection between the HG532e and the computer by pressing the WPS button? Step 1 Check that only one computer tries to connect to the HG532e using the WPS function at a time.
The HG532e is powered off or faulty. Internet Blinking The HG532e is working in routing mode, and it is connected to the Wide Area Network (WAN). Data is being transmitted. The HG532e is working in routing mode, and it is connected to the WAN.
Page 25
The wireless function is disabled, or the WLAN module is faulty. Blinking The HG532e is connecting to a wireless client such as a computer installed with a wireless network adapter using the WPS function. This process lasts no longer than 120 seconds.
Powers the HG532e on or off. Reset Restores the HG532e to its default settings. To restore the HG532e to its default settings, press and hold the Reset button for over 6 seconds. After the HG532e is restored to its default settings, all user customized data will be lost.
Password for web-based user configuration utility login Wireless network name See the label printed on the label on (SSID) for wireless HG532e's rear panel. connection Password (WLAN Key) See the label printed on the label on for wireless connection HG532e's rear panel.
Page 28
Item Specifications Standards ADSL ITU G.992.1 (G.dmt) Annex A standards ITU G.994.1 (G.hs) ANSI T1.413 Issue 2 ADSL2 ITU G.992.3 (G.dmt.bis) Annex A standards ITU G.992.3 (G.dmt.bis) Annex L ITU G.992.3 (G.dmt.bis) Annex M ADSL2+ ...
Page 29
HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China www.huawei.com...