Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
WS-7016U
Wireless 433 MHz
Temperature Station
Instruction Manual
Viewing Remote Control
Senders
Features of the Multiple Remote
Control Senders
Warranty Information
FCC DISCLAIMER
INVENTORY OF CONTENTS
1. The Indoor Temperature Station (Figure 1)
2. The Outdoor Remote Control Sensor
(TX3U) and mounting bracket. (Figure 2)
3. 3 each, 1/2" Philips screws.
4. One strip of double sided adhesive tape.
1
13-16
16-18
18-21
21-22
22-23
24-28
28-29
29-31
31-33
34
3
TABLE OF CONTENTS
Topic
Inventory of Contents
Additional Equipment
Remote Control Sender
Indoor Temperature Station
Features
Indoor Minimum and Maximum
Temperatures
Outdoor Minimum and
Maximum Temperatures
Resetting the Indoor Minimum
and Maximum Temperatures
Resetting the Outdoor Minimum
and Maximum Temperatures
5. Instruction Manual and Warranty Card.
Figure 1
Figure 2
ADDITIONAL EQUIPMENT (not included)
1. 1 Philips screwdriver.
2. 1 Flat screwdriver.
3. 2 Fresh AA 1.5V batteries.
4. 2 Fresh AAA 1.5V batteries.
QUICK SETUP
1. Insert two AAA batteries into the Remote
Control Sender.
2. Insert two AA batteries into the Indoor
Temperature Station.
Page
1
1
2
3-6
3-4
5-6
7-8
8
9
10-11
11-12
12
13
2
4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for La Crosse Technology WS-7016U
Summary of Contents for La Crosse Technology WS-7016U
- Page 1 WS-7016U Wireless 433 MHz Temperature Station Instruction Manual Remote Control Sender Indoor Temperature Station Using Multiple Remote Control Senders Setup of Multiple Units Viewing Remote Control Senders Features of the Multiple Remote Control Senders Troubleshooting Maintenance and Care Instructions Specifications...
- Page 2 3. Wait 5-6 minutes, or until the outdoor temperature is displayed in the OUTDOOR LCD (Liquid Crystal Display) of the Indoor Temperature Station. 4. Set the Time (See complete instructions for details). 5. Mount units. Note: The Remote Control Sender transmits a signal every 3 minutes.
- Page 3 2. Observing the correct polarity, install 2 AA batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temperatures are shown on the Indoor Temperature Station. 5. The Indoor Temperature Station should now show: “-:- -” in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s.
- Page 4 B. OUTDOOR MINIMUM AND MAXIMUM TEMPERATURES 1. Press and hold the OUTDOOR button for 1 second. “MIN” appears in the OUTDOOR LCD. The “OUTDOOR MIN,” and “TIME” displays will flash. The recorded minimum temperature is displayed in the OUTDOOR LCD, and the time it was recorded is displayed in the TIME LCD.
- Page 5 The Remote Control Sender can be mounted in two ways: with the use of screws or, using the adhesive tape. 1. MOUNTING WITH THE SCREWS a) Remove the mounting bracket from the Remote Control Sender (figure 2). b) Place mounting bracket over desired location.
- Page 6 VIII. USING MULTIPLE REMOTE CONTROL SENDERS Your WS-7016U Indoor Temperature Station can receive signals from five different Remote Control Senders (The TX3U features temperature data transmission and the TX3UP offers the same plus a 10’ probe to insert in a pool, spa, soil, etc.).
- Page 7 Temperatures can vary depending on the location of the Remote Control Sender. The thermometers are not 100% accurate (the WS-7016U is accurate to +/- 2 F). If you are sure the temperature is wrong (the unit reads 110 F, when it is actually 70 F) reset entire system by removing...
- Page 8 Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. Opening the casings invalidates the warranty. Do not try to repair the unit. Contact La Crosse Technology repairs. SPECIFICATIONS Transmitting Frequency 433MHz Recommended Operating Temperature Indoor Temperature 32F to 122F...
Need help?
Do you have a question about the WS-7016U and is the answer not in the manual?
Questions and answers