SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range 3. Test method 1.1 This spec sheet is applied all of the 32/37/42" LCD TV with 3.1 Performance : LGE TV test method followed LA63E chassis.
Page 7
5. Chroma & Brightness 5.1 FOR 32LC2D CONDITION : EZ-Picture "Normal" Item Unit Remark White peak brightness cd/m HDMI input, full white Contrast Ratio 600:1 800:1 Brightness uniformity Refer to LCD SPEC. Color coordinate 0.633 +/- 0.03 0.339 +/- 0.03 GREEN 0.286 +/- 0.03...
Page 8
5.3 FOR 42LC2D CONDITION : EZ-Picture "Normal" Item Unit Remark White peak brightness cd/m HDMI input, full white Contrast Ratio 600:1 800:1 Brightness uniformity Refer to LCD SPEC. Color coordinate 0.633 +/- 0.03 0.339 +/- 0.03 GREEN 0.286 +/- 0.03 0.610 +/- 0.03 BLUE...
ADJUSTMENT INSTRUCTION 1. Application Object If you turn on a still screen more than 20 minutes (Especially These instructions are applied to all of the LCD TV, LA63E. Digital pattern(13 CH), Cross Hatch Pattern), an afterimage may occur in the black level part of the screen. 3.
Page 11
(3) Click the first icon shown in fig.9. The window seen in (3) Click the Send. fig.10 should appear. (4) When you see (ISP COMPLETE) the download is complete. 3-4. Set Method (1) MCU Select: MTV512M64 (2) Option R/W Option: Auto Write(Verity) Jig Option: Myson Transmit Speed: Medium (3) Check: Just do it with blank micom.
Page 12
4-3. Adjustment 4. ADC-Set Adjustment (1) Select Component1 as the input with 100% Horizontal 4-1. Synopsis Color Bar Pattern(HozTV31Bar) in 480i Mode (2) After receiving signal for at least 1 second, press the ADJ ADC-Set adjustment to set the black level and the Gain to Key on the Service R/C to enter the ‘Ez - Adjust’...
Page 13
[37LC2DA] :EDID for HDMI-1 (DDC (Display Data Channel) Data) EDID Block 0 table = [32LC2DA] :EDID for HDMI-1 (DDC (Display Data Channel) Data) EDID Block 0 table = 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01...
Page 14
[42LC2DU] 7. Adjustment of White Balance :EDID for HDMI-1 (DDC (Display Data Channel) Data) EDID Block 0 table = 7-1. Required Equipment (1) Color analyzer (CA-100 or CA210 similar product) 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 (2) Automatic adjustor (with automatic adjustment necessity 10 00 10 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23 and the RS-232C communication being possible)
8. Shipping Conditions Item Condition Remark Input Mode TV02CH Volume Level Mute Aspect Ratio 16:9 Video EZ Picture Daylight Contrast Brightness Color Sharpness Tint Color-temperature Cool Auto(On) Advanced Cinema3:2 Mode(Off) Black Level(RF,HDMI=>Low) Audio Audio Language EZ Sound Normal Balance Treble Bass Front Surround TV Speaker...
SVC REMOCON To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function. MUTE To check TV screen image easily.