Related Manuals for ACR Electronics Earlswood EW1MF
Summary of Contents for ACR Electronics Earlswood EW1MF
- Page 1 TECHNICAL MANUAL Multifuel Stove Model EW1MF To be retained by the user for future reference Serial Number ……………………………. Document EW1MF 0209 Thank you for purchasing an ACR Heat Products stove.
- Page 2 The Earlswood stove is exempted (under Section 21 of the Clean Air Act 1993) for use in a smoke control area when burning wood. It is a multifuel appliance and can also burn suitable smokeless fuels (Authorised fuels under Section 20 of the Clean Air Act) in a smoke control areas. To ensure that you gain the most from your purchase, please take a few minutes to read through this manual before lighting the appliance for the first time.
- Page 3 EARLSWOOD SPECIFICATIONS Nominal heat output ………… 5 kW – WOOD 4.8 kW – SMOKELESS FUEL Chimney draft required ……… 12Pa Height …………………………… 525mm Width ……………………………. 480mm Depth ……………………………. 335mm Weight …………………………… 80kg Air Requirement ……………….. Nil *** Flue Mass Gas Flow …………… 4.3 g/s – WOOD 7.1 g/s – SMOKELESS FUEL Mean Flue Gas Temperature ..
- Page 4 Location of the unit Clearances to non-combustible materials There must be a minimum clearance of 150mm at each side of the appliance. A clearance of 150mm is required at the back of stove (if the rear wall has a thickness of 200mm or more this measurement can be reduced to 50mm) A minimum clearance of 150mm is required above the appliance.
- Page 5 Flue Requirements The chimney must comply with current Building Regulations. Provision must be made to provide access for cleaning the appliance, the flue gas connector and the chimney flue. The flue must be: In sound condition and provide sufficient draft ...
- Page 6 The internal vermiculite panels of the appliance should be checked regularly for soundness. If any wear and tear is found, we recommend these parts are replaced immediately. Check the rope door seals are intact and are not worn. These should be replaced on an annual basis to ensure the correct operation of this appliance.
- Page 7 Prohibited Fuels Green wood – i.e wood which is less than 2 years old with a moisture content of above 20% Recovered wood – i.e pallets, railway sleepers etc. These will have been chemically treated and will pollute the atmosphere and possibly overheat the appliance.
- Page 8 Re-fueling Always refuel onto a bed of hot embers. Never overload the stove – it will work very well with two medium sized logs. Once you have added more fuel, leave the door slightly ajar for a few moments afterwards to allow the initial volatiles in the fuel to burn. Once the new fuel is established, close the door and control the burn rate as above.
- Page 9 Troubleshooting Problem Probable Cause Action Recommended Fire difficult to Green wood / wet wood Use hardwood logs Start / Fire goes with a maximum moisture content of 20% Logs are too large Use small logs to start The fire and once Established use split logs Not enough primary air Open air control...
- Page 10 Commissioning Check List (Please mark box when completed) Ensure the serial number has been recorded on the front of this manual for any future use Ensure the door seals are in good condition and that the glass is secured correctly in the door (do not over tighten the glass as this will prohibit its expansion and could cause the glass to crack) Ensure that all internal components are fitted correctly (these may have shifted in transit)
- Page 11 Warranty Certificate The specifications within this document are provided for information purposes only and are under no circumstances binding. With the aim of constantly improving our products, all modifications considered necessary may be made without notice. Our appliances are guaranteed against faults and hidden defects subject to the following conditions: ...
- Page 12 Warranty Claim Form Customer Name: ……………………………………………………………………… Customer Address: ……………………………………………………………………. ……………………………………………………………………………………………… ……………………………………………………………. Postcode …………………. Daytime Tel: ……………………………. Mobile Tel: ……………………………… Model Name: …………………………… Model Number: ………………………. Serial Number: …………………………………………………………………………. Date of purchase: …………………………………………………………………….. Date of installation: …………………………………………………………………… Installer’s Name and address: ……………………………………………………… ………………………………………………………………………………………………...