Miele G 2872 Operating Instructions Manual
Miele g 2872 dishwasher
Hide thumbs
Also See for G 2872:
- Operating instructions manual (80 pages) ,
- Technical information (240 pages) ,
- Manual (46 pages)
Related Manuals for Miele G 2872
Summary of Contents for Miele G 2872
-
Page 1: Operating Instructions
Operating Instructions Dishwasher G 2872 en - US, CA To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 07 329 160... -
Page 2: Table Of Contents
Contents IMPORTANT SAFETY INSTRUCTIONS....... . . 4 Guide to the dishwasher ..........7 Control panel . - Page 3 Contents Settings ............40 Drying Plus.
-
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS WARNING – Electrical Safety Before installation, make sure that When using your dishwasher, follow the voltage and frequency listed on the basic precautions, including the data plate correspond with the following: household electrical supply. This data must correspond to prevent injury and Read all instructions before machine damage. - Page 5 A damaged appliance is Do not install this dishwasher dangerous. Unplug the machine and beneath a cooking surface, oven or any call your Miele dealer or the Miele appliance that radiates heat. Technical Service Department. High temperatures from these units Ensure that any plastic wrappings, may damage the dishwasher.
- Page 6 If the power cord is damaged it before using the dishwasher. This will must only be replaced by a Miele release any accumulated hydrogen Service technician with a genuine Miele gas. Do not smoke or use an open power cord.
-
Page 7: Guide To The Dishwasher
Guide to the dishwasher a Upper spray arm (not visible) g Triple filter system b Cutlery tray h Data plate c Upper basket i Optical interface d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual compartment detergent (depending on model) dispenser f Lower spray arm... -
Page 8: Control Panel
Guide to the dishwasher Control panel e K button (Information) a Selection buttons To select a menu point from this To display more info about the display, to change the displayed displayed menu value (+/-) or to browse between f g On button with indicator menus. -
Page 9: Display Function
Guide to the dishwasher Display function The following can be selected in the display A bullet in the display next to the touch control shows that a function can be – the wash program selected with this control. – the options –... -
Page 10: Caring For The Environment
Caring for the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. -
Page 11: Before Using For The First Time
Before using for the first time To open the door To close the door ^ Push the baskets in. ^ Lift the door and push until the catch engages. The door will then close automatically. Do not put your hand inside of the door as it is closing. -
Page 12: Welcome Screen
Before using for the first time Welcome screen ^ Turn the dishwasher on g. A Welcome screen shows when the washer is turned on for the first time. Language setting The display changes automatically to the language setting. } deutsch B Sprache F } english (GB) OK }... -
Page 13: Time Of Day Setting
Before using for the first time Time of day setting The display changes automatically to the time of day setting. : 00 Please set the time of day OK } ^ Set the hours using the controls and confirm with Set the minutes and confirm. -
Page 14: Water Softener
Before using for the first time Water softener Checking the water hardness The water hardness measured by the Every dishwasher is tested before sensor can be displayed. leaving the factory. Any water See "Settings J - Water hardness". remaining in the machine is from the final factory test and does not indicate that the machine has been used. -
Page 15: Filling The Salt Container
Before using for the first time Filling the salt container Inadvertently filling the salt container with dishwashing detergent will damage the water softener. Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener. ^ Place the provided funnel over the ^ Remove the lower basket and salt container. -
Page 16: Rinse Aid
Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. Filling the rinse aid reservoir with detergent will damage the reservoir. -
Page 17: Rinse Aid Refill Message
Before using for the first time Rinse aid refill message Insufficient rinse aid When the message first comes on, there will be enough rinse aid left for 2 - 3 washes. ^ Refill rinse aid after the program has finished. If the "Tab"... -
Page 18: Loading The Dishwasher
Loading the dishwasher ^ The spray arms must not be blocked Do not wash items soiled with by items that are too tall or hang ash, sand, wax, grease or paint in through the baskets. Check the dishwasher. clearance by manually rotating the Ash and sand do not dissolve and spray arms. -
Page 19: Items Not Recommended For Dishwashing
Loading the dishwasher Items not recommended for Glassware: dishwashing – There are no standard guidelines for washing glassware, when in doubt – Cutlery with wooden handles wash by hand. – Wooden cutting boards – When purchasing new dishes, – Glued items such as old knives with glasses and cutlery, make sure they handles glued together around the are dishwasher safe. -
Page 20: Split Cutlery Tray
Loading the dishwasher Split cutlery tray ^ Arrange the cutlery as shown in the cutlery tray. Spoons with thick handles may have to be placed as knives and forks with their heads in the holders. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. -
Page 21: Upper Basket
Loading the dishwasher Upper basket Removable spike insert The spike insert can be removed to Always use the dishwasher with create more space for larger items, the upper and lower basket inserted. e.g. a saucepan. Tall items (except during the program). - Page 22 Loading the dishwasher Adjustable cup racks Coffee bar ^ Raise the rack to make room for tall (depending on model) glasses. Lower it to double stack Glasses can be leaned against the smaller pieces. coffee bar to allow a firm stand. The height of the cup rack can be adjusted in two levels.
- Page 23 Loading the dishwasher Universal support bar The support bar will hold tall glasses and stemware securely. ^ Fold the bar down and lean the desired glasses against it. ^ If desired, a section of the cutlery tray can be removed to allow for even taller glasses.
-
Page 24: Adjusting The Upper Basket
Loading the dishwasher Adjusting the upper basket Depending on the setting of the upper basket, a variety of plate dimensions The upper basket can be raised or can be accommodated. lowered to accommodate tall items. For example: If the upper basket is in The basket can also be angled to fit tall its highest position a plate with a items in both, the upper and lower... -
Page 25: Lower Basket
Loading the dishwasher Lower basket Foldable spikes ^ For larger and heavier items such as The foldable spikes can be used for plates, serving platters, saucepans, small plates and saucers. bowls, etc. Small plates and saucers can also be arranged in the lower basket. Two rows of spikes can be folded down, to create more room for larger dishware, e.g. - Page 26 Loading the dishwasher Removable spike insert Removeable PlateGuard Plus with StemGuard The spike insert can be removed in order to make room for larger tableware (depending on model) or to use a different insert. This insert is ideal for cups, glasses, plates, bowls, pots and pans.
- Page 27 Loading the dishwasher Vase / Bottle insert (depending on model) The vase / bottle insert can be used to rinse narrow items, e.g. vases, baby bottles, etc. Removing the insert a: ^ To remove the insert, gently pull the handle upwards. Inserting the insert b: ^ Place the insert into the lower basket.
-
Page 28: Basket Accessories
Basket accessories Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or Miele. Depending on the model some accessories come standard with the machine. Glassware insert GGO To wash long stemmed glassware, attaches to the upper basket... -
Page 29: Use
Fill the detergent dispenser only tabs may not dissolve completely. when you are ready to start the dishwasher. Dishwasher cleaning products are available from MIele. Only use detergents formulated for domestic dishwashers. Use only the recommended amount of detergent. Continued use of too much detergent may cause machine damage. -
Page 30: Adding Detergent
^ Add detergent to compartment II and Adding detergent close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. ^ To open, press the latch on the detergent dispenser. -
Page 31: Selecting A Program
Turning on ^ Make sure the spray arms can rotate freely. ^ Close the door. ^ Open the water supply, if closed. ^ Turn the dishwasher on g. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. -
Page 32: Program Guide
Program guide Program When to use Program sequence Main Interim rinse Final Drying rinse wash rinse Normal For normally soiled dishware with dried on food Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, 120% detergent recommended China &... - Page 33 Program guide Program When to use Program sequence Pre-rinse Main Interim rinse Final Drying wash rinse Light Soiling For lightly soiled dishware, e.g. party dishware Energy Saver The water intake temperature must be 115°F (45°C) for light to normally soiled dishware Plastics To gently clean...
-
Page 34: Use
^ Select the desired options. The detergent type can now be set. The selected options are marked with a You can choose between powder, L check. gel or Tabs. See "Settings J - Tab". ^ To de-select an option press the respective touch control again. -
Page 35: Starting A Program
Starting a program Time display ^ Select Start Before the program starts, the time display shows the running time of the Close the door The display shows selected program in hours and minutes. To select another program or to add During the running program the Back options, select... -
Page 36: At The End Of A Program
At the end of a program Interrupting a program At the end of a program the optical A program is interrupted as soon as the control light flashes slowly with the door door is opened. If the door is closed, closed. -
Page 37: Changing A Program
Changing a program If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. 12:00 Sensor Wash 1:32 h Main wash Cancellation } ^ Select Cancellation and confirm with... -
Page 38: Additional Options
Additional options Delay start The starting time of a program can be delayed between 15 minutes and 24 hours. The start can be delayed in 15-minute-increments. When using the "Delay Start" function make sure that the detergent compartment is dry before adding detergent, use a cloth if necessary. - Page 39 Additional options ^ Confirm with The display changes to the program menu. ^ Select Start ^ Close the door. The program starts automatically at the selected time. The indicator d goes out. Starting a program before the delay start has elapsed: A program can be started before the delay start time has elapsed.
-
Page 40: Settings
Settings The "Settings J" menu allows you to adjust standard settings Opening the Settings J menu ^ Turn the dishwasher on by pressing the g button. The main menu shows in the display. If the memory function is selected, the last selected program is displayed. - Page 41 Settings Language J Time of day The display contents can be shown in This selection allows the clock to be different languages. shown as 24 or 12 hours. The clock can also be set from here. The displayed language can be Language changed by the submenu Setting the clock format...
- Page 42 Settings Detergent To achieve best results the used If the "Tab" indicator is lit than the detergent can be set on your program sequence is adapted to suit dishwasher. The selections available detergents than contain rinse aid and are "Powder", "Gel" and "Tab". The salt (as well as other components program cycle sequence will be where applicable).
-
Page 43: Drying Plus
Settings Drying Plus °d gr/gal Setting in display The Drying plus function automatically opens the door slightly at the end of a program, in order to improve the drying process. This function can also be deactivated. ^ Select the desired setting and confirm with Water hardness The dishwasher is equipped with a... -
Page 44: External Water Softener
Settings External water softener Filter check If the dishwasher is connected to an This selection allows you to set the external water softener unit which is number of cycles run before the filter regenerated with salt, the water check message shows. hardness must still be set in the You can select between 30 and 60 dishwasher. -
Page 45: Reorganize Program List
Settings Reorganize program list The order of the programs in the program list can be reorganized. The two most frequently used programs can be saved to the first two positions. } Sensor Wash B } Cancel Select program for position 1 Continue } ^ Select with e the program which you would like to save to the first position of the main menu. -
Page 46: Save Options
Settings Save options Temperature Additional options can be selected for The temperature can be displayed in some programs, e.g. extended drying. "°C/Celsius" or "°F/Fahrenheit". See "Use - Selecting options". The temperatures are shown in Save options allows you to save the °C/Celsius by default. - Page 47 Settings Buzzer Buzzer volume When the buzzer is activated, a tone Two buzzer volumes can be selected or sounds at the end of a program and if a the buzzer can be turned off. fault occurs. The buzzer at the end of a program is The buzzer tone at the end of a turned on by default.
-
Page 48: Button Tone
Settings Button tone Memory A tone will sound when a button is The memory function allows you to save pressed. the last selected program. The volume can be set to seventeen When turning the dishwasher off and on different levels. It is set to level 8 by again after a program has finished or default. -
Page 49: Factory Default
Settings Dealer Turning the demo mode on ^ Select the desired option, confirm Demo modes are only for with showrooms. ^ Confirm the following messages with The dishwasher has three demo programs for showrooms. ^ Press any button to start the selected The programs "Demo mode"... -
Page 50: Frequently Asked Questions
Frequently asked questions With the aid of the following guide, minor problems can be fixed without a service call. Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. - Page 51 If the problem persists, contact Technical Service. Fault Waterproof F70 The waterproof system – Turn off the water supply. has activated. – Contact Miele Technical Service. Automatic door closing The door may be – Remove the item, if fault blocked.
-
Page 52: Problems Water Intake/Drain
Frequently asked questions Problems water intake/drain Issue Possible fault Solution The optical interface flashes fast, the buzzer sounds and the display shows the fault: No water intake The water supply is Open the water supply all closed. the way. Fault water intake FXX Before fixing the fault: –... - Page 53 Frequently asked questions Problem Possible fault Solution The optical interface The intake water does – Restart the program. flashes fast. not have a minimum – If the fault is displayed The program "Energy temperature of 115°F again, use a different Saver"...
-
Page 54: General Problems With The Dishwasher
Frequently asked questions General problems with the dishwasher Problem Possible fault Solution The display remains The display has gone Press a button. off. into "Standby" mode to The display turns on again. save energy. The display shows the The middle or lower Open the dishwasher door spray arm is blocked by and rearrange items blocking... - Page 55 Frequently asked questions Problem Possible fault Solution Detergent is left in the The dispenser was damp Dry the dispenser before dispenser at the end when detergent was adding detergent. of a program. added. The detergent lid Detergent residue is Remove the residue. cannot be closed blocking the catch.
-
Page 56: Sounds
Frequently asked questions Sounds Issue Possible fault Solution There is a knocking The spray arm is hitting an Interrupt the program, noise in the wash item in the basket. rearrange items blocking cabinet. the spray arms. There is a rattling Items are not secure in the Interrupt the program and wash cabinet. -
Page 57: Poor Cleaning Results
Frequently asked questions Poor cleaning results Issue Possible fault Solution The dishes are not The dishes were not loaded See "Loading the clean. correctly. dishwasher". The program was not Select a more intensive powerful enough. program, see "Program Guide". Stubborn but normal soiling Use the function "Adjust (e.g. - Page 58 Frequently asked questions Issue Possible fault Solution Dishes are not dry, The rinse aid setting may be Increase the dosage, refill glasses and cutlery too low, or the rinse aid the reservoir or switch the are spotted. reservoir is empty. rinse aid product when refilling, see "Before using for the first time".
- Page 59 Frequently asked questions Issue Possible fault Solution Glasses are Detergent deposits. Use a different detergent. discolored and the film cannot be wiped off. Glasses are dull and Glasses are not dishwasher There is no remedy. Only discolored, film safe. wash dishwasher safe cannot be wiped off.
-
Page 60: Comparison Tests
Comparison Tests 10 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray... - Page 61 Comparison Tests 12 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray...
- Page 62 Comparison Tests 14 place settings, Standard program: Normal Upper basket Lower basket Cutlery tray...
-
Page 63: After Sales Service
Miele products will not be recognized to input these into your machine by Miele. Our goal is to prevent controls via the indicator light marked unauthorized (and untrained) service PC. Miele will provide information when personnel from working on your Miele such possibilities become available. -
Page 64: Transport
Transport To transport the dishwasher, e.g. when moving to a new home, note the following: – Empty the dishwasher. – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. -
Page 65: User Maintenance Instructions
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use. -
Page 66: Cleaning And Care
The wash cabinet can be cleaned with a dishwasher cleaner such as "Dis Cleaner" available from your Miele dealer, Miele or online at www.miele.com. Door and the door seal ^ Wipe the door seals regularly with a damp cloth to remove food deposits. -
Page 67: Control Panel
Cleaning and Care To prevent damage to your appliance avoid the following: – cleaners containing soda, ammonia, thinners, or chlorides – cleaners containing descaling agents, – abrasive cleaners, – stainless steel cleaners, – dishwasher soap (powder), – caustic (oven) cleaners, –... -
Page 68: Triple Filter System
Cleaning and Care Triple filter system Cleaning the triple filter The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones, etc.). - Page 69 Cleaning and Care ^ Return the filter so it lies flat in the To clean the underside of the filter the flap must be opened. base of the wash cabinet. ^ Push the clips together a and open ^ Lock the filter by turning the handle the flap b.
-
Page 70: Cleaning The Spray Arms
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). -
Page 71: Cleaning The Water Inlet Filter
^ Reinsert the filter and seal. Make sure connection is recommended. These filters can be purchased from Miele. they are seated correctly. ^ Screw the intake hose back on the Cleaning the filter... -
Page 72: Cleaning The Drain Pump And Non-Return Valve
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. -
Page 73: Installation Instructions
Installation Instructions For installation of the dishwasher please refer to the Installation Sheet supplied with these instructions. -
Page 74: Electrical Connection
V 1-800-565-6435 right side of the door. A damaged power cord must only Specifications be replaced with a genuine Miele The dishwasher comes equipped with a cord by a Miele service technician. 4 ft (1.2 m) power cord with a molded... -
Page 75: Plumbing
Waterproof system – The inlet hose is approximately 5 ft. (1.5m) long. A 5 ft. (1.5m) extension All Miele dishwashers have a safety valve hose is available from Miele. located on the incoming water line and a sealed underside with a water sensor. -
Page 76: Drainage
7/8" (22 mm). remove the lower basket. – Drain hose extensions and adapters ^ Pull the lower spray arm firmly can be ordered from Miele. The maximum drain hose length is upwards to remove. 13 ft. (4 m), max. drain height: 39"... -
Page 77: Remotevision
RemoteVision The Miele RemoteVision system is Be sure your wireless system meets the designed to send messages directly to following requirements Miele and/or your PC. ® – Windows XP or newer operating ® For information on set-up and system, Mac OS X 10.3 or higher... - Page 80 Alterations reserved/4308 M.-Nr. 07 329 160 / 02 G 2872 For the most updated manual see the Miele web site.