Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hills NVC-BM1
Summary of Contents for Hills NVC-BM1
- Page 1 Network Camera Installation manual NVC-BM1 NVC-DF1 NVC-DT1 NVC-DM1 V1.1...
- Page 2 Congratulations on the purchase of your Hills Professional CCTV solution. It’s important that you read this installation guide thoroughly before installation. Thank you for choosing Hills. Part no. Model no. Type Model S47092 NVC-DT1 Eyeball Dome camera 3MP IR Eyeball Camera (4mm)
-
Page 3: Table Of Contents
2 NVC-DF1 - 3MP IR Dome Camera (4mm) --------------------------------------------------------- 10 2.1 Overview --------------------------------------------------------- 10 2.2 Installation --------------------------------------------------------- 11 3 NVC-BM1 - 3MP IR Bullet Camera (4mm) --------------------------------------------------------- 14 3.1 Overview --------------------------------------------------------- 14 3.2 Installation --------------------------------------------------------- 15 4 NVC-DM1 - 3MP IR Mini Dome Camera (4mm) ----------------------------------------------------- 17 4.1 Overview... -
Page 4: Nvc-Dt1 - 3Mp Ir Eyeball Camera (4Mm)
NVC-DT1 - 3MP IR Eyeball Camera (4mm) 1.1 Overview Product Structure Diagram Figure 1-1 Table 1-1 Description Description Ethernet interface, PoE Power Cable, 12V DC Trim Ring Camera Note: This camera supports Power over Ethernet (PoE), and the standard power supply is 12V DC. If a power adaptor is used please make sure that it is compatible with the camera. -
Page 5: Installation
1.2 Installation Before you start, please verify the package contents are correct by checking the items against the carton content list in the Quick Guide, and make sure all the components are included. Note: Please make sure that the wall is strong enough to withstand three times the weight of the camera. - Page 6 There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below. Side Outlet Figure 1-4 Note: Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling.
- Page 7 4. Adjust the Lens Loosen the lock screw. Rotate the enclosure to adjust the pan angle; rotate the camera to adjust the tilt angle. Tighten the lock screw to clamp the lens. Lock Screw Figure 1-6 5. Install the Trim Ring Attach the trim ring to the camera.
-
Page 8: Nvc-Df1 - 3Mp Ir Dome Camera (4Mm)
NVC-DF1 - 3MP IR Dome Camera (4mm) 2.1 Overview Figure 2-1 Overview Table 2-1 Physical Description Description Mounting base Horizontal stand Vertical stand Lower dome Cables Plate of infrared lamp Lens Black Liner Safety rope... -
Page 9: Installation
2.2 Installation Notes: Do not place the camera in extremely hot or damp environment. To avoid heat accumulation, good ventilation is required for a proper operating environment. Ceiling mounting is recommended for this camera. The ceiling must be thick enough to withstand more than three times the weight of the camera. - Page 10 2) Fix the mounting base on the ceiling with screws. Figure 2-4 Fix the Mounting Base Note: If required, you can route cables through the side opening on the side of the mounting base. Side opening Figure 2-5 Side Opening 3.
- Page 11 Note: As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 4. Install the dome cover Reinstall the lower dome and tighten the screws. Figure 2-7 Reinstalling...
-
Page 12: Nvc-Bm1 - 3Mp Ir Bullet Camera (4Mm)
NVC-BM1 - 3MP IR Bullet Camera (4mm) 3.1 Overview Figure 3-1 Product Structure Diagram Table 3-1 Physical Description Description Adjustable Bracket Back Box Front Box Lens Sun Shield Power & Network cable Grounding Screw Reset 3.2 Installation Note: Please make sure that the ceiling or wall is strong enough to withstand three times the weight of... - Page 13 Steps: 1. Install the Camera This series of camera is designed as a whole compact structure, and you only need to secure the mounting base to the ceiling with the supplied screws. Figure 3-2 Secure the Camera to the ceiling 2.
-
Page 14: Overview
NVC-DM1 - 3MP IR Mini Dome Camera (4mm) 4.1 Overview Figure 4-1 Overview Table 4-1 Physical Description Description Cover Lens Power LED indicator* Base plate Set screw hole Set screw of lens S & L: Network status LED indicator.# RESET: Reset button. (*) It is solid red when power is applied to the unit. -
Page 15: Installation
4.2 Installation Note: The ceiling mounting is recommended for this camera. If required, you can use a plier to remove the clip on the side of the back box and then route cables through the opening to secure the cables on the ceiling. Figure 4-2 Remove the Clip Steps: 1. - Page 16 Figure 4-4 Fix the Base Plate 2. Adjust the Lens 1) View the video image of the camera over the network. 2) Loosen the lens set screws. Figure 4-5 Loosen Set Screws 3) Insert the hex key into the hole marked in the 0 and rotate the hex key to adjust the panning position and tilting position until getting the desired surveillance angle.
- Page 17 Figure 4-6 Adjust Image Notes: As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. Reinstall the cover before viewing the image of the camera because you may get an unclear image without the cover.
- Page 18 Figure 4-7 Reinstall...
- Page 19 For further information, including datasheets, FAQ and technical support please visit: www.hills.com.au/videosecurity...