LCD TV SERVICE MANUAL CHASSIS : ML-041D MODEL : 27LZ5RV-ZC CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL. DVD / CD PLAYER...
SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
SPECIFICATION NOTE : Specifications and others are subject to change without notice for improvement. 1. Application range This specification is applied to ML-041D chassis. 2. Requirement for Test Testing for standard of each part must be followed in below condition. (1) Temperature: 25°C ±...
Page 7
4.General Specification Item Specification Unit Remark Panel 27" TFT WXGA LCD Frequency range H : 31 ~ 61Khz DVI-I input V : 56 ~ 75Hz Control Function 1) Contrast/Brightness 2) H-Position / V-Position 3) Tracking : Clock / Phase 4) Auto Configure 5) Reset Comoponent Jack 1 : Y...
Page 8
5.Optical Feature(LCD Module) Item Specification Remark Viewing Angle R/L, U/D 176,176 <CR 10> Luminance Luminance (cd/m2) Typical Variation MAX / MIN Contrast Ratio 1000 All white / All black CIE Color Coordinates White Typ. 0.284 Typ. 0.295 Typ. Typ. Green Typ.
Page 9
7. Component Video Input (Y, PB, PR) Specification Proposed Resolution H-freq(kHz) V-freq(Hz) 640x480 15.73 SDTV, DVD 480i 640x480 15.63 59.94 SDTV, DVD 480i 720x576 15.625 50.00 SDTV, DVD 625 Line 8. PC INPUT Mode table [Timming chart of Receivable Mode] Resolution H-freq(kHz) V-freq.(Hz)
Page 10
9. Customer Menu Setup [shipped condition: PAL] Item Condition Remark Power Volume Level Main Picture Input Main Last Channel Pr 01 Mute 16 : 9 Station Auto Program Manual Program Program Edit Favorite Program None Picture Dynamic Dynamic Contrast Brightness Colour Sharpness Tint...
ADJUSTMENT INSTRUCTION 1. Application Object 3.4 Video signal Gain/Offset Adjustment(Auto adjustment) - Execution of White Pattern during Heat Run over 30min This instruction is for the application to the LCD TV. - Connect to the LCD TV AV1 Scart input terminal with Patten Generator(MSPG-925FS) - Convert INPUT MODE to Video&Confirm whether PSM 2.
Page 12
3.6 EDID (The Extended Display Identification Data) - Connect D-Sub to DVI-I Cable to DVI-I Jack. - Confirm the pc display by inputting the Analog signal. - After displayed, input the Analog EDID data. - Connect DVI D Cable to DVI Jack. - Confirm the pc display by inputting the Digital signal.
Page 13
* Option(PAL) Item Condition Remark Option1 SideAV 0 : SideAV Off 1 : SideAV On SCART 0 : SCART Off 1 : SCART On 0 : PC Off 1 : PC On SideComp 0 :SideComp Off 1 :SideComp ON 16:9 0 : Wide OFF 1 : Wide On 200PR...
SVC REMOCON FUNTION REAMARK To turn the TV on or off POWER To turn the TV on automatically if the power is supplied to the TV. (Use the POWER ON POWER key to deactivate): It should be deactivated when delivered. To activate the mute function.
TROUBLESHOOTING No power :[A]Process (LED indicator off) No Power Check 24V or 12V (LED indicator off) Faill of Power B/D Pass Check Output of Change L3, L1300 Faill L3, L1300 Check Output of Change IC1300, IC4 or IC6 IC1300, IC4 or IC6 Faill Pass Change LED Assy...
Page 16
No Raster :[B]Process Check LED Status Repeat A PROCESS on display unit Faill Check L900,L901 Change L900,L901, L902,L903 L902,L903 Faill Pass Check the input/ Change IC901 Output of IC901 Faill Pass Check inverter Change inverter Connector or inverter connector or inverter Faill Pass Change panel link...
Page 17
No Raster on Component signal Repeat [A] Process Pass Check the signal of Change Q310,Q315,Q316 Q310,Q315,Q316 Faill :[C]Process Pass Re-soldering or Check the input/ Change the defect part Faill output of IC800 Check IC800 Pass Re-soldering or Check the input/ Change the defect part Faill output of IC600...
Page 18
No Raster on AV Signa No Raster on TV(RF) signal (Scart1.Scart2,S-Video) Check 5V,33V of TU1000, Repeat Check the output of Re-soldering of Change the [A] Process TU1000 Faill Faill defect part Pass Change Check the signal of Q317,Q318,Q308, Q317,Q318,Q308,Q313 Faill Q313 Pass :[C]Process...
Page 19
No Raster on DVD Signal Repeat [A] Process Pass Check the signal of Check P1200,P1202 or R1211,R1212,R1213 DVD Cable Faill Pass :[C]Process - 19 -...
Page 20
No Sound(RF,SIDE AV) No Sound(Scart1/2,DVD,PC) Check the Change source input input source Faill Pass Re-soldering or Check the input/output Change the defect part Faill of IC1 Check X11 Pass Re-soldering or Check the input/ Change the defect part output of IC401 Faill Check IC403,X601 Pass...
Page 23
BLOCK DIAGRAM DESCRIPTION 1. Video Controller Unit & Display Data Conversion Unit The video controller unit receives the video signals inputted through the tuner, AV port, and converts them into an ITU656 signal through the microcomputer (VCTI) combined with the video decoder that integrates various functions in one chip.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN, CH : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit in the CQ : Polyestor RS : Metal Oxide Film P/No. means as follows; CE : Electrolytic RN : Metal Film CF : Fixed Film RH : CHIP, Metal Glazed(Chip)