Download Print this page

Advertisement

Quick Links

USER'S GUIDE 2609/2639
MA0302-A
How a Radio-controlled Watch Works
What is a radio-controlled watch?
Your radio-controlled watch is designed to receive a time
calibration signal that contains standard time data and adjust its
current time setting accordingly.
Time Calibration Signal
The time calibration signal is the same one used by TV and radio
stations to keep accurate time and sound their time signals. The
standard time data of the time calibration signal is controlled by
cesium beam atomic clock.
Time data
After the watch receives the Japan Standard Time signal, it
performs internal calculations to determine the current time.
Because of this, there may be an error of up to one second in
the displayed time.
Location
Reception is difficult and may even be impossible in the locations
described below. Avoid such locations when performing signal
reception.
You should think of your watch operating like a radio or TV when it
is receiving the calibration signal.
Among or near buildings
Near high-voltage lines
Next to a household
Inside a vehicle
appliance or office equipment
(automobile, train, plane, etc.)
(TV, speaker, fax, PC, etc.)
In a location where there is
Near mountains
radio interference
(construction site, airport, etc.)
If you are experiencing problems with reception, move away
from the types of locations described above to a location with
better reception, and try again.

Calibration Signal

The Japanese calibration signal (Call Sign: JJY) is maintained by
the independent Japan Ministry of Posts and Telecommunications
Communication Research Laboratory (CRL). It is a long wave
signal transmitted 24 hours a day from the Mt. Otakadoya
transmitter (40kHz) located in Tamura-gun, Fukushima Prefecture,
and from the Mt. Hagane transmitter (60kHz) located on the
border between Saga Prefecture and Fukuoka Prefecture.
The U.S. calibration signal (Call Sign: WWVB) is transmitted by
the National Institute of Standards and technology from Fort
Collins, Colorado.
Though the calibration signal is normally transmitted 24 hours
a day, transmission may be interrupted occasionally due to
maintenance, lightening, etc.
Signal received using
Transmitter
built-in antenna.
Long-wave time
calibration signal
Watch decodes
received data
and converts it
to time data.
Signal data
Decoding
Time is
Time data
adjusted
Cesium
according to
Watch
Inside the watch
atomic clock
time data.
Receiving the Calibration Signal
There are two methods you can use to receive the time calibration
signal.
Auto reception (Reception is performed automatically at 2:00,
3:00, 4:00, and 5:00 each morning.)
Manual reception (You initiate reception using a button
operation.)
The watch is set up for auto reception at the factory, so all you
need to do is to place it in a location that allows good reception
each night.
Setting Up to Make Reception Easier
Remove the watch from your wrist and place it somewhere so its
top (12 o'clock side, where the antenna is located) is facing
approximately in the direction of the signal transmitter. Keep the
watch away from metal objects.
Resin band
Metal band
Orienting the watch so it is sideways to the transmitter makes it
more difficult to receive the signal.
Do not move the watch while it is receiving the calibration signal.
The following explanation covers the radio-controlled timekeeping function only.
For other functions, go to the download page for Module 2608 or 2638,
which are the export models that have the same functions, except for radio-controlled timekeeping.
Reception Range
This watch is designed to receive the standard time calibration signal of Japan (JJY) or of the United States (WWVB). The signal that is
received depends on the current Home City setting.
When this Home City is selected:
Transmitter Locations
500km
500km
Mt. Hagane
(60kHz)
1000km
Under optimum conditions, the calibration signal should be
receivable up to 1,000 kilometers from the transmitter. Note
that the wave is relatively weak at distances greater than
500km, so reception may be poor at long distances.
Geographic contours, nearby buildings, the season, and the time of day can make reception impossible even when you are within range of
the transmitter.
Best reception is possible late at night.
Time Required for Reception
Signal reception takes anywhere from about two to six minutes.
Note that when "AUTO" is specified as the frequency selection
mode, signal reception can take up to 12 minutes.
* See "Specifying the Transmitter Selection Mode in Japan" for
more information.
Triggering Reception Manually
In the Timekeeping Mode:
Hold down the D D D D D button for
about two seconds.
The watch beeps and reception
starts. Ongoing reception is
indicated by the
icon and the
receive indicator. See "Receive
Receive icon
Icon and Indicator" for more
information.
To interrupt reception
Press the D D D D D button.
All other buttons besides D
are disabled during signal reception.
When reception is successful
The watch terminates reception and adjusts the current time. Next
it beeps and then displays the date and time the adjustment was
performed.
The
icon and the receive indicator remain on the display to
indicate that reception was successful. The
from the display each day at 3:00 a.m.
When reception fails
The watch does not adjust its current time setting, and displays
"ERR" instead.
The display also return to the normal timekeeping screen
automatically if you do not perform any operation for about one
or two minutes.
You can receive this signal
Either the Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal (60kHz)
Fort Collins, Colorado signal
1000km
Transmitter Location
1000km
Mt. Otakadoya
(40kHz)
Fort Collins
Under optimum conditions, the calibration signal should be
receivable up to 3,000 kilometers from the transmitter. Note
that the wave is relatively weak at distances greater than
1,000km, so reception may be poor at long distances.
Receive Icon and Indicator
While reception is in progress, the
icon and the receive indicator
cycle from "Unstable" through
"Stable" as shown below. How far
they cycle depends on the signal
strength. Keep the watch in a
location where reception is stable
while reception is in progress.
Module 2609
Unstable
Receive indicator
Module 2639
Unstable
Even under optimum reception conditions, it takes at least
icon is cleared
10 seconds before reception starts.
Use the receive icon and receive indicator to check
reception status and to determine the best location for
signal reception.
Note that weather, the time of day, surroundings, and other
factors can all affect reception.
3000km
Stable
Stable
1

Advertisement

loading

Summary of Contents for Casio 2609

  • Page 1: Calibration Signal

    USER’S GUIDE 2609/2639 The following explanation covers the radio-controlled timekeeping function only. For other functions, go to the download page for Module 2608 or 2638, MA0302-A which are the export models that have the same functions, except for radio-controlled timekeeping.
  • Page 2: Troubleshooting

    The following explanation covers the radio-controlled timekeeping function only. USER’S GUIDE 2609/2639 For other functions, go to the download page for Module 2608 or 2638, which are the export models that have the same functions, except for radio-controlled timekeeping. Specifying the Transmitter...

This manual is also suitable for:

2639