Sony NEX-FS700 Service Manual page 10

2-1-7. MOUNT BLOCK SECTION
ns : not supplied
301
(including IC9001 (CMOS imager) and IS-102 board)
(Note 5)
#11
306
305
#234
304
303
(Note 4)
302
320
321
Ref. No. Part No. Description
301 A-1885-380-A SERVICE, MOUNT BLOCK ASSY (_)
(including IC9001 (CMOS imager) and IS-102 board) (Note5)
302 4-269-054-01 MB N PLATE (A (945))
* 303 4-185-963-01 MB N PLATE SP (Note 4)
304 4-425-279-01 RING (960), LENS
305 4-299-974-01 BUTTON, L LOCK
306 X-2582-840-1 PIN ASSY, L LOCK
307 4-257-700-01 SPRING, LOCK (L)
308 4-425-282-01 CABINET, MT INNER
309 A-1876-371-B MB CONTACT UNIT (755), N
310 A-1885-295-A MT-076 BOARD, COMPLETE
311 4-424-696-01 MB SHEET (960), MASK
312 A-1889-736-A NDF UNIT SERVICE (Note 6)
313 4-424-716-01 MB RUBBER (SG), SEAL
NEX-FS700/FS700K/FS700C/FS700CK/FS700E/FS700EK/FS700J/FS700JK/FS700R/FS700RH/FS700U/FS700UK
ns
#271
310
#69
309
307
#50
308
315
317
316
314
(Note1, 2)
#49
313
#271
#49
A
ns
314
312
(Note1, 2)
(Note 6)
Ref. No. Part No. Description
* 314 Selection Parts IM WASHER (A), ADJUST (Note 1, 2)
315 1-968-297-11 HARNESS (COAXIAL CABLE)
316 3-079-115-01 TAPE AS
317 4-425-280-01 HEAT SINK, MT
318 2-590-635-01 TAPE (AS 1/2)
319 4-408-292-01 SHEET, CM RADIATION (Note 3)
320 4-188-536-01 CAP, BODY
321 4-441-046-01 SPACER, ND
#11 3-078-890-11 SCREW, TAPPING
#49 2-630-005-31 SCREW (M2), NEW TRUSTER, P2
#50 2-891-494-11 SCREW (M2), NEW TRUSTER, P2
#69 2-599-475-21 SCREW (M1.7)
#234 4-186-545-11 SCREW, 0+Z M1.7 SG (SPIN)
#271 3-270-483-01 GRIP, (M1.7 X 4.0) (2 MAIN EG)
Screw
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
311
4.0
#271: M1.7 X 4.0
ns (Black)
3-270-483-01
A
1.7
4.0
Note
Note 1: The IM adjust washers (A) differ in thickness.
Make sure to return the removed IM adjust washers to
319
original places.
(Note 3) When replacing IM adjust washers, refer to "SELECTION
PARTS".
If the original state cannot be restored due to loss of the IM
adjust washer, for example, replace the Mount Block Assy
#50
(Service).
Note 1: IM
IM
IM
PARTS"
IM adjust washer
318
SELECTION PARTS
Ref. No.314
Select the optimum thickness of washer.
316
315
* 4-185-995-01 IM WASHER (A), ADJUST (t = 0.05)
* 4-185-995-11 IM WASHER (A), ADJUST (t = 0.1)
* 4-185-995-21 IM WASHER (A), ADJUST (t = 0.15)
* 4-185-995-31 IM WASHER (A), ADJUST (t = 0.2)
* 4-185-995-41 IM WASHER (A), ADJUST (t = 0.25)
* 4-185-995-51 IM WASHER (A), ADJUST (t = 0.3)
* 4-185-995-61 IM WASHER (A), ADJUST (t = 0.35)
* 4-185-995-71 IM WASHER (A), ADJUST (t = 0.4)
* 4-185-995-81 IM WASHER (A), ADJUST (t = 0.45)
* 4-185-995-91 IM WASHER (A), ADJUST (t = 0.495)
Note 2: Refer to "Assembly-4: Putting position of the IM Adjust
Washer (A).".
Note 2: "Assembly-4: Putting position of the IM Adjust Washer
(A)."
Note 3: Refer to "Assembly-5: Attaching method of the CM Radiation
Sheets.".
Note 3: "Assembly-5: Attaching method of the CM RadiationSheets."
2-9
#49: M2.0 X 4.0 #50: M2.0 X 3.0 #69: M1.7 X 3.0
(Black) (Red)
2-630-005-31 2-891-494-11
2.0 2.0
4.0 3.0
Note 4: Refer to "Assembly-6: Apply grease on the MB N Plate SP.
Note 4: "Assembly-6: Apply grease on the MB N Plate SP."
Note 5: Precautions for Replacement of the Mount Block Assy
Service
(A) As Mount Block Assy Service may be damaged by static
electricity from its structure, handle it carefully like for the
MOS IC.
"SELECTION In addition, ensure that the receiver is not covered with dust
nor exposed to strong light.
Mount Block Assy (Service)
Note 5:
Note 6: New NDF Unit Service is attached two Protection Sheets
When assemble this part, peel off two sheets.
Note 6:
#234: M1.7 X 5.5
(Silver) (Silver)
2-599-475-21 4-186-545-11
1.7
1.7
3.0 5.5
Assy
Assy
MOS IC
NDF Unit Service Protection Sheet 2