Viviox Pandora H600 Operating Instructions

Installation and Operational Guide
Please read the manual below for important information on your Viviox
product that could prevent damage or serious injury. Failure to follow our
instructions and other safety precautions could result in serious injury to
you or your passengers, and/or product and vehicle damage.
Important: The installation technician and operator must read this manual
before starting installation or operation of your new product. They must
have a thorough understanding of automotive systems, electronics and
procedures.
WARNING: Please understand that the user and installer assume
ultimate, complete and full responsibility in determining proper mounting
location and positioning. When installing, consider a location based on its
ability to provide total safety to all passengers.
WARNING: DO NOT USE CIRCUIT BREAKERS WITH THIS
PRODUCT! All customer-supplied wires that connect with the
positive (+) end of the battery must be able to support 125% or more of the
maximum operating current. They MUST be fused with the battery to
handle the current.
OPERATION
1. Operation Instructions (see diagram above:
In order to activate your Pandora, connect the red wire to a 12V post
and the black wire to the ground post of the vehicle's battery.
2. Changing Patterns:
Patterns can be changed by momentarily connecting the blue wire to
the ground of your vehicle's battery.
Less then a second Next Pattern
1-3 Seconds Previous Pattern
3-5 Seconds Factory Default
5+ Seconds Turn off and Reset
1. Syncing Instructions: Configure both Pandora's to the same pattern in Phase 1
and connect the yellow wires from each light head together.
2. To have your Pandora's alternate: Set every other light to the same pattern in
Phase 2 and connect the yellow wires. To better understand how this feature works,
each light head coming from the factory will display Phase 1.In order to have one
Pandora alternate with another, every other light needs to be advanced to Phase 2
of the current pattern.
Model H600
Pandora Series
RED
Positive
BLACK
GND-Ground
BLUE
Pattern
YELLOW
Sync
Ÿ
Before drilling and installation, check both sides of your mounting
service.
Ÿ
Grommets should be installed into all wire passage holes.
Ÿ
Please read your vehicle's owner's manual; it contains important
information about the airbag deployment area. This product should
NOT, under any circumstances, be installed in the deployment area of
the vehicle's airbag. Do NOT route any wires in this area. Having
equipment mounted or located in this area is a serious risk; it could
reduce or damage the airbag's effectiveness, or even become a
projectile that could result in serious injury or death.
Ÿ
This device may feature powerful, bright, high-intensity LED lights. DO
NOT look at the lights directly, as momentary blindness and/or
permanent eye damage can occur.
Ÿ
DO NOT try to activate or control this product during a hazardous or
dangerous driving situation.
Ÿ
If your device is controlled or activated by a remote, please double
check that the control is in a place that will allow for both the control
itself, as well as the vehicle, to be used safely in any driving condition
and/or situation.
FLASH PATTERNS
1: Single 120 FPM Ph1-Color 1&2
2: Single 120 FPM Ph2-Color 1&2
3: Single 120 FPM Ph1-Color 1
4: Single 120 FPM Ph2-Color 2
5: Single 120 FPM Alt. Color 1<-->2
6: Single 300 FPM Ph1-Color 1&2
7: Single 300 FPM Ph2-Color 1&2
8: Single 300 FPM Ph1-Color 1
9: Single 300 FPM Ph2-Color 2
10: Single 300 FPM Alt. Color 1<-->2
11: Single 75 FPM Ph1-Color 1&2
12: Single 75 FPM Ph2-Color 1&2
13: Single 75 FPM Alt. Color 1<-->2
14: Double 75 FPM Ph1-Color 1&2
15: Double 75 FPM Ph2-Color 1&2
16: Double 75 FPM Alt. Color 1<-->2
17: Double 120 FPM Ph1-Color 1&2
18: Double 120 FPM Ph2-Color 1&2
19: Double 120 FPM Alt. Color 1<-->2
20: Quad 75 FPM Ph1-Color 1&2
21: Quad 75 FPM Ph2-Color 1&2
22: Quad 75 FPM Ph1-Color 1
23: Quad 75 FPM Ph2-Color 2
T. 844.3.VIVIOX
E. support@VIVIOX.com
W. www.VIVIOX.com
24: Quad 75 FPM Alt. Color 1<-->2
25: Quad 120 FPM Ph1-Color 1&2
26: Quad 120 FPM Ph2-Color 1&2
27: Quad 120 FPM Ph1-Color 1
28: Quad 120 FPM Ph2-Color 2
29: Quad 120 FPM Alt. Color 1<-->2
30: Quint 120 FPM Ph1-Color 1&2
31: Quint 120 FPM Ph2-Color 1&2
32: Quint 120 FPM Alt. Color 1<-->2
33: 2 Double 75 FPM, 4 Quad 120 FPM
34: Module Flash Color 1<-->2
35: AUTORUN
36: STEADY BURN
37: OFF