Exploded View And Disassembly - Samsung YP-30S Service Manual
Digital audio player samsung yp-30s
Hide thumbs
Also See for YP-30S:
- Manual (30 pages) ,
- User manual (30 pages) ,
- Manual de usuario (7 pages)
Table of Contents
Advertisement
6. Exploded View and Disassembly Order
Samsung Electronics
AH64-01376A
CABINET-TOP;YP-30S,ANODIZING,AL,0.7T
AH97-00789A
ASSY-CASE BOTTOM; ASSY, YP-30S
AH97-00790A
ASSY-FRAME TOP; ASSY, YP-30S
AH97-00791A
ASSY-FRAME BOTTOM; ASSY, YP-30S
AH97-00792A
ASSY-COVER BATTERY; ASSY, YP-30S
AH64-01407A
WINDOW-LCD; YP-30S, ACRYL, 1.5
AH64-01379A
KNOB-HOLD; YP-30S, ABS
AH64-01382A
DECORATION-RING; YP-30S, ABS
AH61-00790A
HOLDER-LCD; YP-30S, ABS
6003-001257
SCREW-TAPTITE; PH, +, B, M1, L, L6.5, NI PLT, SW
AH92-01100A
ASSY PCB-MIC; YP-30S, ONE-BOARD (For 64MB YP-30S)
AH92-01382A
ASSY PCB-32MB-ONE-BOARD; YP-30S(For 32MB YP-30S/CT)
AH07-00059A
LCD; UG-12T14-FGHT X-A, YP-30S, -, 32X4
AH64-01381A
KNOB-VOLUME; YP-30S, ABS
AH39-00301A
CABLE FORM; YD-150B, YP-MF64,4P, 1.2M, -,-,PVC, BEIGE, 4PX1200MM,-,USB CABLE
AH59-01014A
SPEAKER SYSTEM; YP-30S, YH-30SGU, 0.22V,0.2
AH61-00845A
HANGER-NECKLES; YP-30S
AH63-00380A
BAND; -,-,PVC, YP-30S,DOMESTIC(For Asia)
AH63-00328A
BAND-ARM; -,-,PVC,YP-30S(Except Asia)
AH97-00844A
ASSY-CRADLE; -,YP-30S
AH80-00028A
INSTALL-MFN CD; YP-30S,30S CD, CD, KOR-CD
Disassembly and assembly method
1. Remove No . while pressing No. "PUSH OPEN".
2. Remove No.
3. Remove No.
4. Pull and remove No.
while pressing the upper part of No.
5. Carefully extend No.
a little, and lift up and remove it along with the main body
6. Remove No.
7. Lift No.
up (separate it No. , No. , No. and No. ).
8. Lift the No.
LCD connector up.
9. After lifting No.
up from the connector lightly, apply heat with a soldering iron on the soldering part.
10. Separate No.
and No. .
Cautions in assembling
1. After ensuring No.
is properly placed at No. , insert frame (without care, SW2 or SW3 may be damaged).
2. Since a flaw may occur if lifting No.
up from the lower part and then inserting it, lower it down from the upper part for insertion.
3. Securely insert No.
and No.
into the No.
connector and then fix them at the PCB.
(Back light soldering condition of LCD: 360˚C, within 2 seconds)
4. When properly placing No.
(+, -), adjust orientation accurately.
Exploded View and Disassembly Order
(take care so that No.
switch would not be pressed).
6-1
Advertisement
Table of Contents
