Kustom Wav 1000 Owner's Manual page 11

Editing the Digital Effects
The presets contain valid parameters under any condition.
This makes Programming and Editing the same function.
The word "Edit" will describe both programing and editing
functions.
The parameters of the 3 presets stored in the active
Favorite bank can be edited while in the Edit mode. This
allows you to hear your changes and compare them
between channel selections before saving. The active
Favorite button and one of the group buttons will flash
while in the edit mode. The effect group button lit or
flashing indicates the Level can be adjusted. Notice there is
also a red rectangle around the effect group name to the
left of the level on the VFD display.
How to edit the Digital Effects:
Selecting different effects
Press any of the Effect Group buttons. They flash
indicating you are in edit mode but no changes are
made, even when the illuminated group button is
pressed. An illuminated or flashing effect Group button
indicates it is selected.
Select any of the 15 effects in a selected group or
bypass it by repeat pressing the group button. The effect
name is indicated on the display. The word "
the display indicates the effect group is turned off. Each
time you press a flashing group button, the effect in that
group moves up to the next one. You can also hold
down the button to scroll through the effects. If you
pass up the effect you want, continue scrolling until you
reach the effect again. The chart in Fig. C shows how
the effects in the 3 groups are organized.
Change the level of an effect group
The selected effect group button is illuminated. Rotate
the Level control to raise or lower the level of the
selected effect group. The effect group levels (
indicated on the display to the right of the group name.
A red illuminated rectangle around a group name
indicates it can be adjusted using the Level control.
Type
Not Active
Single Short Delay
Single Medium Delay
Single Medium Delay
Single Medium Delay
Single Medium Delay
Single Medium Delay
Single Medium Delay
Multi Tap Delay
Multi Tap Delay
Multi Tap Delay
Multi Tap Delay
Multi Tap Delay
Multi Tap Delay
Regen 40% Delay
Regen 40% Delay
Effect group selections
DELAY
Variation Display Name Type
BYPASS Not Active
50ms 50 ms Chorus
100ms 100 ms Chorus
200ms 200 ms Chorus
250ms 250 ms Chorus
300ms 300 ms Tremolo
350ms 350 ms Tremolo
400ms 400 ms Chorus
Triplet Triple 1 Leslie
Triplet Pan Triple 2 Leslie
4/4 Time 1 4/4 1 Flanger
4/4 Time pan 1 4/4 2 Flanger
4/4 Time 2 4/4 3 Flanger
4/4 Time Pan 2 4/4 3 Pitch Shifter 1
100ms Regen 1 Pitch Shifter 1 Light Detune
200ms Regen 2 Pitch Shifter 1 Deep Detune
EXAMPLE
The Reverb Group of Favorites 1 Rhythm channel
preset is being edited.
To avoid repeating
steps during an Edit,
press SAVE every
time you achieve
desirable results.
Making temporary changes
Once you get your effects set up, you may not want to
make permanent changes during a performance.
As long as you stay on the same Favorites bank and
not disrupt the AC power, you can make temporary
changes without saving. This makes it easy to change
settings for different room acoustics.
" on
Saving the temporary changes
Press the Save button. All 3 presets in the selected
Favorites bank are saved.
Delete temporary changes and use saved Presets
Method 1
Select a different Favorites Bank without pressing
save. The temporary changes are lost and originals
restored the next time the un-saved Favorite Bank is
selected.
) are
Method 2
Turn power off then on again. Any changes not saved
before turning off power will be lost.
Fig. C
MODULATION
Variation Display Name
BYPASS
Light Depth 1 Chor 1
Light Depth 2 Chor 2
Hi Depth 1 Chor 3
Hi Depth 2 Chor 4
Slow TREMO 1
Fast TREMO 2
Fast 2 FST Chor
Slow Leslie S Room Hi Damp
Fast Leslie F
Light 1 Flange 1
Light 2 Flange 2
Deep Stereo Flange 3 Reverse Gate Lo Dens. 100ms
Doubler Doubler Reverse Gate Hi Dens. 300ms
L Detune Forward Gate Lo Dens. 100ms
D Detune Forward Gate Hi Dens. 300ms
11
Rotate to change Reverb Level
DIGITAL EFFECTS
FAVORITES GROUP LEVEL
DEL
1 2
SAVE MOD
3 4
PUSH ON
REV
Press REV button to select next
effect in Reverb Group. Hold to
scroll through.
For example,
The current effect for the Reverb
Group is HALL 1.
Looking at chart Fig. C, HALL 1 is
first effect in the group. If you want
to select ROOM 1 (the fourth effect
in the group), you would press REV
button 3 times or hold it to scroll up
to the ROOM 1 effect.
REVERB
Type Variation Display Name
Not Active BYPASS
Hall 1 1s HalL 1
Hall 1 3s HalL 2
Hall 1 5s HalL 3
Room .5s ROOM 1
Room 1s ROOM 2
Room 2s Room 3
Room 4s ROOM 4
3s ROOM 5
Hall 2 6s HalL 4
Hall 2 10s HalL 5
L to R Gate Hi Dens. 500ms L-R Gate
Rev Low
Rev High
Fwd Low
Fwd High
Current group
levels
Illuminated red
rectangle
Indicates Reverb
Group is being
edited.