Advertisement
Quick Links
GUCBIR GENERATOR
GJB13000E / GJB13000E-3 USER MANUAL
Congratulation and thank you for your purchase our products; out aim is to provide a
high-quality generator set to achieve customer satisfaction, and we are confident that
your choice will be justified.
This manual, dealing with the generator side of the unit, gives all the basic information to
ensure satisfactory and reliable operation of your.
Please use this manual as a companion to the other manual covering the engine side.
1
Advertisement
Related Manuals for Gucbir GJB13000E
Summary of Contents for Gucbir GJB13000E
- Page 1 GUCBIR GENERATOR GJB13000E / GJB13000E-3 USER MANUAL Congratulation and thank you for your purchase our products; out aim is to provide a high-quality generator set to achieve customer satisfaction, and we are confident that your choice will be justified. This manual, dealing with the generator side of the unit, gives all the basic information to ensure satisfactory and reliable operation of your.
- Page 2 Caution 1. Use SAE 10W-30 Lubrication oil. After the first oil change at 10 hours operation, change it every 50 hours. 2. Do not connect the generator output to commercial AC outlets. 3.For information about the engine operation and maintenance, please see[IMC or HONDA engines Owner’s Manual]...
- Page 3 Ⅰ NAMES OF IMPORTANT PARTS AND COMPONENTS...
- Page 4 MODEL 11000 11000S 13000 13000S Prime 8.5KW 8.5KW 10.5KW 10.5KW 50 Hz Standby 10.5KW 10.5KW 11.5KW 11.5KW AC Output Prime 10.0KW 10.0KW 12.0KW 12.0KW 60 Hz Standby 11.0KW 11.0KW 13.0KW 13.0KW Rated Speed 3000rpm(50Hz)/3600rpm(60Hz) Single Three Single Three Phase GENERATO Two line(4) Four line Two line(4)
- Page 5 MODEL GX620 GX670 Prime 16.0hp/3000rpm,18.0hp/3600pm 18.0hp/3000rpm,20.0hp/3600rpm Output Standby 18.0hp/3000rpm,20.0hp/3600pm 20.0hp/3000rpm,22.0hp/3600rpm Type 4-stroke,overhead valve,2 cylinders(90 v-Twin) Cylinder Volume 614cc 627cc NO.of Cylinder Starting System Electric(Recoil) 3.5L/hour 3.7L/hour Fuel Consumption (at full load) (at full load) Fuel Tank Capacilty Noise level(7m/dB) 72/50Hz, 78/60Hz 71/50Hz, 77/60Hz Net Weight(with Wheels) 151(160)kg...
- Page 6 Ⅱ PREPARATORY STEPS FOR OPERATION 1. ENVIRONMENTAL REQUIREMENTS 1-1.Outdoor use A) Istall your gasotine generator unit in a dry and dustless place. B) Avoid the direct sunshine. Place your IMC G.G.unit in the shade. C) Keep your gasotine generator unit on a level ground so that the unit will not move by itself.
- Page 7 1-2.Indoor use A) Use in well-ventilated areas, or vent exhaust outsids and away from any building air intakes. A large volume of air is required for the operation. B) Keep the air inlet/outlet and the exhaust gas outlet 1.5m away from any obstacle. C) Use under 40 degrees temperature.
- Page 8 2. PREPARATION FOR THE ENGINE A) Check level of fuel gasoline, Lubrication OIL. Add any of those fluids if it is below the sufficient level specified in the Engine Owner’s Manual. B) Check all major bolts and nuts on the engine. Tighten any loose bolts and nuts.
- Page 9 Ⅲ SAFETY PRECATIONS FOR SERVICING A. Only qualified persons should test, maintain, and repair this unit. B. Always wear a face shield, rubber gloves and protective Clothing when working on the unit. C. Do not touch the generator unit or any part of load with your bare hands or wet hands.
- Page 10 E. Do not breathe exhaust fumes. F. Stop engine and let it cool off before checking or adding fuel. G. Do not add fuel while smoking or if unit is near any sparks or open flames. H. Observe correct polarity (＋＆－)on batteries. I.
- Page 11 Ⅳ WARM-UP PROCENDURE A. Check all fluids daily(The unit is shipped without lub. oil). B. Turn the fuel cock to [ON] position. C. Set the main switch to [OFF]. D. Pull out the choke lever. E. Turn the engine start key to [START] position. F.
- Page 12 Ⅴ STARTING – UP PROCEDURE A. Retum speed control lever to left position. B. Ensure voltmeter indicates normal. (Single phase 220V)(Three phase 380V) C. Set the main switch to [NO]. D. Observe the voltage is in the normal loaded range.
- Page 13 Ⅵ STOP PROCEDURE A. Set the main switch to [OFF] B. Turn the engine start key to [STOP] position. C. Close the fuel cock if the unit is in storage or transportation.
- Page 14 Ⅶ SIMPLIFIED TROUBLESHOOTING GUIDE This guide is intended to give a brief information for troubleshooting with no testing or measuring instruments to check the unit. However, testing and measuring instruments are required to diagnose parts and compo nents in many trouble cases. If you cannot determine the cause by visual inspection, you should consult yout dealer Whom you purchased this unit from.
- Page 15 Ⅷ Malfunctions and countermeasures Single – phase/ Three – phase...