Magnavox MRD733B Setup Manual

SETUP MANUAL
MRD733B
See the Online Owner's Manual for details:
www.MAGNAVOX.com
Step 1 Please visit website www.MAGNAVOX.com
Step 2 Select Download.
Step 3 Type in the Model # "MRD733B" and click "Search".
Step 4 Select the Manual, and click on "Download".
MAGNAVOX is a registered trademark of Philips Electronics North
America Corporation and is used by Funai Electric Co., Ltd. and Funai
Corporation, Inc. under license from Philips Electronics North America.
For product recycling information, please visit - www.magnavox.com
Click on
© 2012 Funai Electric Co., Ltd.
Printed in China
EDC11UD
1VMN32374 ★★★★★
* 1 V M N 3 2 3 7 4 *
1
CONNECTIONS
Connection to a TV and Speakers
HDMI cable (not supplied)
SPEAKERS ( 3 )
VIDEO AUDIO IN or or
SUB- FRONT REAR FRONT OUT AUX
WOOFER CENTER R L R L
+ R HDMI IN
DIGITAL
- AUDIO IN L
COAXIAL
LAN HDMI OUT
REAR FRONT
VIDEO IN
SUB- FRONT
R L R L
WOOFER CENTER
Audio / Video cables
+
(not supplied)
-
FRONT FRONT
RIGHT LEFT
FRONT
CENTER
1. Press the clamper 2. Release the
and insert the wire. clamper.
REAR REAR
SUBWOOFER RIGHT LEFT
Wired and Wireless Connections
Wireless
Wireless Connection
broadband router
Active Internet connection is required to your
or
modem or broadband router. Please check with your
ISP (Internet Service Provider) for further assistance.
Wired Connection LAN cable
(not supplied)
Modem or
SPEAKERS ( 3 ) VIDEO AUDIO IN
REAR FRONT OUT AUX
WOOFER SUB- CENTER FRONT R L R L Router
+ R
DIGITAL
- AUDIO IN L
COAXIAL
LAN HDMI OUT
2

INITIAL SETUP

Please locate the Source /
Input / AUX / Video button
on TV's remote control. The
button may vary on the TV
brand and model. Once you
have located the button,
AV/SOURCE AV/SOURCE A A
press until you see "Please
Wait..." or the Initial Setup
Power Button
Menu on the Screen.
Initialization
Welcome!
This unit is ready for initialization. Please
follow the on-screen instructions.
Next
Cancel
Return
Select your language.
Quick Start Mode
Would you like to activate the Quick Start Mode?
The unit will start up more quickly, but will consume
more power in standby mode.
On
Off
Return Return
Network Selection
Please select the connection method.
Wired
Wireless
Return
Cancel
1 / 7
4
WIRELESS SETUP
Network Setup
AUDIO OUT
Network Selection
Please select the connection method.
Wired
Wireless
Return
Cancel
1 / 7
If your router has a PBC*
( Push Button Configuration )
Connect
button, you can use
"Push Button Method"
which is the easiest way to
set up a wireless connection.
If your router does not have it,
please use the "Auto Scan" setup.
* PBC button may be called WPS
Internet button on your wireless router.
D Note
• If you are experiencing signal
issues with your wireless
connection, please confirm that
your wireless router is placed
close enough to the unit.
3
WIRED SETUP
e Source /
ideo button
control. The
Please W Please Wait...
y on the TV
el. Once you
e button,
see "Please
nitial Setup
reen.
Language Language
Please select your language for on-screen
display.
English
Español
Network Selection
Français
Please select the connection method.
Wired
Wireless
Return
Cancel
1 / 7
Automatically check for latest software
Would you like to set On the Auto software
update feature? When connected to the Internet,
the unit will automatically check for the latest
software.
On
Network Settings
Off
Select whether to set the IP address and other
settings automatically or manually.
Auto
Manual
Return
Cancel
If you select "Wired",
4 / 7
please go to in step 3 .
If you select "Wireless",
please go to in step 4 .
Auto
Access Point Setting
Network Selection
Scan
Please select the setting mode. Please select the access point.
Wireless Access Point A
Auto Scan
Wireless Access Point B
Manual
Easy Connect (WPS) Wireless Access Point C
Wireless Access Point D
Retry
Wireless Access Point E
Return
Return
Wireless Access Point F
Cancel
Cancel
3 / 7
2 / 7
Access Point Setting
Network Settings
Select whether to set the IP address and other
Please confirm the setting.
settings automatically or manually.
SSID : Wireless Access Point A
Auto
Security : WPA-PSK (AES)
Manual
Next
Retry WEP/WPA Key : xxxxxxxxxxxxxxxxxxxxxxxx
Return
xxxxxxxxxx
Return
Cancel
Cancel
4 / 7
3 / 7
Easy
Network Settings Access Point Setting
(WPS)
Push Button Method
Please select the setting mode.
Please push the PBC (push button configuration) on the wireless router
and select 'Push Button Method' button on screen.
Auto Scan
Manual
PIN Code Method
Easy Connect (WPS)
Please input the PIN number into the wireless router and select
Return Return
'PIN Code Method' button on screen.
Cancel Cancel PIN Code is: xxxxxxxx
2 / 7 2 / 7
After clicking [OK] on "Push Button Method", push the PBC button on your wireless router.
When the unit has successfully been connected to an access point,
appears in the upper left corner of the Home Menu screen.
* This icon does not necessarily mean that this unit is connected to the Internet.
Wireless network setting is completed.
You are ready to enjoy network features over WiFi !
Network Setup
No power.
Network Settings
Please wait a moment. Please press [RETURN] to
No sound or picture.
stop this operation.
State : Setting...
Network Setup
6 / 7
It may take a few minutes.
No reaction to the
Network Settings
remote control.
Please wait a moment. Please press [RETURN] to
stop this operation.
State : Connecting...
6 / 7
It may take a few minutes.
No high-definition
video signal on the TV
Network Settings
screen.
Distorted picture.
Home Network : Pass
Internet : Pass
Network connection succeeds.
End
7 / 7
No sound or
distorted sound.
No 5.1-channel audio
from the speaker
system.
Network Setup
Video and Audio from
the supplied speakers
are not synchronized.
Cannot play back a
disc.
Access Point Setting
Please input the WEP/WPA key with software keyboard.
Cannot connect to
the network.
Done Return Clear a/A/@
3 / 7
Enter the security key to your
wireless router. Key content is case-sensitive.
From here on, the headers will show
"Access Point Setting" when using
"Easy Connect (WPS)" setup.
It may take a few moments.
Network Settings
Cannot use the
wireless connection.
Home Network : Pass
Internet : Pass
Network connection succeeds.
End
7 / 7
If "Home Network" passed,
but "Internet" failed, please
contact your Internet service If you do not find a solution above, please visit our website
provider for troubleshooting assistance.
www.magnavox.com
Please download it and then refer to "TROUBLESHOOTING" section
for more information. If additional support is required, please contact
our Customer Service at 1-800-605-8610.
• If this unit becomes inoperative, do not try to correct the problem
by yourself. There are no user-serviceable parts inside. Eject the
disc (if possible), disconnect the USB Memory Stick (if connected),
place the unit into Standby mode, unplug the power plug, and then
please visit:

TROUBLESHOOTING

Problem Tip
• Check the AC power cord, if it is properly connected.
• Unplug the AC power cord, and wait for about 5-10
seconds. Plug it back in and attempt to Power On the unit.
• Make sure both the TV and Home Cinema are Turned
On.
• Confirm the connections to the TV are made properly as
shown in CONNECTIONS.
• Check to see whether the connected TV or another
device supports HDCP. (This unit will not output a
video signal unless the other device supports HDCP.)
• Confirm that the player's AC power cord is plugged into
a power outlet.
• Check the batteries in the remote control, and make
sure they are inserted properly by + or - symbols.
• Aim the remote at the unit's remote receiver. Then
press any arrow key and confirm the Power-On indicator
dims and blinks when a remote button is pushed. This
confirms that unit is receiving the remote IR signal.
• Does the disc contain high-definition video and the TV
support it? High-definition video is only available when
the disc contains it and the TV supports it.
• Sometimes a small amount of picture distortion may
appear. This is not a malfunction.
• Connect this unit directly to the TV. If Audio / Video
cables are connected to a VCR, pictures may be
distorted due to the VCR copyright protection system.
• Adjust the volume.
• Check to see if the speakers are connected correctly.
• Check the HDMI, COAXIAL and AUX connections as
necessary.
• Make sure the HDMI cable is not plugged into an HDMI-
DVI adapter which does not handle Digital sound.
• Does the disc contain 5.1-channel audio? The 5.1-channel
audio is only available when the disc contains it.
• If a disc has 7.1ch sound this Home Cinema will convert it
to 5.1ch sound output.
• Set "Audio Output" to "Speakers" in "Settings".
• Press [MODE] then check to see if the surround mode is
not set to "2.1ch Stereo".
• Set the audio delay time (0 - 300 ms) in "Audio Sync" under
"Audio Out" in "Settings". "Audio Sync" only functions
when the supplied speakers are connected to the unit.
• Make sure that the product supports the disc.
• Check the region code of the disc. This unit supports
the following region codes.
- Blu-ray Disc™: "A" - DVD: "ALL" or "1"
• Clean the disc.
• Check to see if the modem / router has Power turned On.
• Confirm, if the Internet light is showing activity (light
blinking) on the modem / router.
• Check network settings on the unit. Please refer to
Online Owner's Manual.
• Power cycle the modem's and/or router's AC plug from
its AC outlet for 30 seconds, and then plug it back in.
Then, try reconnecting cords. If you have a telephone
/ Internet modem with your cable service, then you
may have to use its reset button or remove the backup
battery to reset this type of modem. Now wait for the
lights to show activity and try reconnecting.
• Check the cable connections to the router.
• Once you have activated the wireless connection, please
wait 30 seconds for the connection to be established
after Turning On the unit, before trying to access
network features such as BD-Live™, DLNA home
network server and the third-party network services.
• If appears in the upper left corner of the Home
Menu screen, this unit is connected to an Access Point.
Please contact your ISP for further assistance when you
cannot access BD-Live™ or network services.
for the Online Owner's Manual.

SERVICING

www.magnavox.com/support
or contact: 1-800-605-8610