D-Link AirPlus DWL-G700AP Quick Installation Manual
  1. Manuals
  2. Brands
  3. D-Link Manuals
  4. Wireless Access Point
  5. DWL-G700AP - AirPlus G Access Point
  6. Quick installation manual

D-Link AirPlus DWL-G700AP Quick Installation Manual

G 802.11g wireless access point
Hide thumbs Also See for AirPlus DWL-G700AP:
Table of Contents

Advertisement

Quick Links

This product can be set
up using any current web
browser, i.e., Internet
Explorer 6 or Netscape
Navigator 7 and above.

Before You Begin

It's best to use a computer (with an Ethernet adapter) that is connected to a switch
for configuring the DWL-G700AP. The default IP address for the DWL-G700AP is
192.168.0.50
with a Subnet Mask of 255.255.255.0. You will need to assign your
computer a Static IP address within the same range as the DWL-G700AP's IP address
for the purpose of configuring the DWL-G700AP. See the Appendix if you need
assistance in assigning a Static IP address for your network adapter.

Check Your Package Contents

If any of the above items are missing, please contact your reseller.
©2004, 2005 D-Link Corporation. All rights reserved. Trademarks or registered trademarks are the property of their respective holders.
DWL-G700AP 802.11g Wireless

Access Point

CD-ROM (containing Manual and
Warranty)
Ethernet (CAT5 UTP) Cable
7.5V 1.0A DC Power Adapter
Software and specifications subject to change without notice.
1
DWL-G700AP
D-Link AirPlus
802.11g Wireless
Access Point
Using a power supply
with a different voltage
rating will damage and void
the warranty of this product.
G
TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AirPlus DWL-G700AP and is the answer not in the manual?

Questions and answers

Related Manuals for D-Link AirPlus DWL-G700AP

Summary of Contents for D-Link AirPlus DWL-G700AP

  • Page 1: Before You Begin

    If any of the above items are missing, please contact your reseller. ©2004, 2005 D-Link Corporation. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and specifications subject to change without notice.
  • Page 2 Insert one end of the cable to the Ethernet port on the back panel of the DWL-G700AP and the other end of the cable to an Ethernet Broadband Router (i.e., D-Link DI-604) or Switch (i.e., D-Link DES-1005D). Note: You also have the option of connecting the DWL-G700AP directly to the computer that will be used for configuration.

  • Page 3: Using The Setup Wizard

    When you have completed the steps in this Quick Installation Guide, your connected network should look similar to this: Using the Setup Wizard Open your Web browser and type “http://192.168.0.50” into the URL address box. Then press the Enter or Return key. The logon pop-up screen will appear.
  • Page 4 Using The Setup Wizard (continued) Once you have logged in, the Home screen will appear. Click Run Wizard You will see the following screens. Click Next...
  • Page 5 Using The Setup Wizard (continued) Step 1 - Set up your new password. You have the option to establish a password. Click Next Step 2 - Wireless Setup The default wireless settings are: SSID = default Channel = 6 You can change these settings to match an existing wireless network.
  • Page 6 Using The Setup Wizard (continued) Step 3 - Encryption The DWL-G700AP is capable of two levels of wireless encryption 64-bit and 128-bit. By default the encryption is disabled. You can change the encryption settings for more secure wireless communication. Click Next Your Setup is Complete! Click...
  • Page 7 Click Close You will be returned to the Home tab. Click to Exit For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web-management interface; or to the manual located on the CD-ROM.
  • Page 8 Appendix Assigning a Static IP Address in Windows To assign a Static IP Address to the laptop or computer that you are using to configure the DWL-G700AP, please do the following: Go to Start > Double- click on Control Panel > Double-click on Network Connections >...
  • Page 9 For Windows 2000 users: Go to Start > Settings > Network and Dial-up Connections > Double-click on Local Area Connection associated with the Network Adapter installed on your system> select Properties Click Internet Protocol (TCP/IP) Click Properties Select Use the following IP address Input your IP address and subnet mask.
  • Page 10 For Windows Me and 98se users: Click Internet Protocol (TCP/IP) Go to Start > Settings > Control Panel > Double-click on the Local Area Connection associated with the Network Adapter installed Properties on your system > select Click Internet Protocol (TCP/IP) Click Properties Select...
  • Page 11 Apple Macintosh OS X: Go to the Apple Menu Click on Network and Select System Preferences Select Built in Ethernet in the Show pull-down menu Select Manually in the Configuration pull-down menu Input your IP address and subnet mask. (The IP Address must be within the same range as the DWL-G700AP.

Table of Contents