Charging contact Rechargeable Battery Pack(back) BASE UNIT CONTROLS AND FUNCTIONS PULSE/TONE Switch DC IN 9V Jack TEL LINE Jack DIGITAL CALLER-ID CORDLESS TELEPHONE FT-8800 Antenna Cradle IN USE IN USE/CHARGE LED CHARGE PAGE PAGE Button 900MHz COMPANDOR NOISE REDUCTION Charging Contact...
ALIGNMENT PROCEDURE Base Unit Transmitter Section BASE Unit AF GEN. Test Point Power Connections Meter DC IN TEL Line 1kHz -15dBm 9V Jack Jack Test Point Frequency Counter AC 120V Adapter 60Hz Deviation Mater Preset a) Connect the base RF unit to the base main unit. b) Set the “TONE / PULSE”...
Page 5
Receiver Section Connections BASE Unit AC Voltmeter RF SG Dummy Load (600-ohm) TEL Line Test Point Jack DC Voltmeter DC IN 9V Jack Terminal AC 120V 60Hz Adapter Preset a) Connect the base RF unit to the base main unit. b) Set the “TONE/PULSE”...
Page 6
Handset Unit Transmitter Section Connection HANDSET Unit AF GEN. Test Point Power Meter J603 Battery 1kHz 9mV MIC+Pin Connector Test Point Frequency Counter DC Power Supply Deviation Mater DC 3.8V Preset a) Connect the handseet RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit.
Page 7
Receiver Section Connections HANDSET Unit AC Voltmeter RF SG Dummy Load (150-ohm) Connector Test Point DC Power Supply J603 DC Voltmeter Battery Terminal Connector DC 3.8V Preset a) Connect the handset RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit. c) Turn the DC power supply ON while pressing “...
TROUBLESHOOTING HINTS 1. The bell does not ring. See 2. The bell does not ring When the PAGE SW of the base is pressed, does the & page does not ring. ringer on the handset ring? When the TEL SG is joined Check IC4 and TEL network with the base to make bell circuit.
Page 13
2. The bell does not ring & page does not ring. Can the base and handset be See 3. The base and handset connected? cannot be connected. Press handset DIAL key When the key of the handset is Check IC603. while in TALK MODE.
Page 14
3. The base and handset cannot be connected. Check whether the base Check IC4 and its is able to set in the test peripheral circuit. mode 1. Check the TX POWER Check base RF unit. and the TX FREQUENCY on the base unit. Press “PAGE”...
Page 15
Press “3” key, check Check whether there is a C h e c k R 6 3 5 , R 6 3 6 , whether deviation of the 250 Hz data waveform at R 6 3 4 , R 6 3 2 , R 6 1 9 , TX data is app.
Page 16
4. Cannot make a phone call (pulse). Can the base and handset See 3. The base and handset be connected? cannot be connected. While in TALK MODE, press Check IC2. dial key of the handset. Check whether square waveform from pin 1 of IC2 is fed.
6. Voice cannot be transmitted to other party (outgoing call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, 9.0mV sine Check Q604 and its wavefor m i s a p p l i e d t o peripheral circuit.
Page 18
7. The voice of the caller cannot be heard (incoming call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, 77.5mV sine Check the base TEL-line waveform is applied to TEL- circuit and REPLAY control line of the base, can the 1 kHz circuit.
IC AND TRANSISTOR VOLTAGE CHART Base Unit Unit[V] Unit[V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE 1.7V DC 1.7V DC 2.6V DC 2.6V DC 1.7V DC 1.7V DC 0-3.2V DC 1.7V DC 1.7V DC 3.2V DC 3.2V DC 0.7V DC 1.7V DC...
Page 20
Unit[V] Unit[V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE 2.6-3.8V 2.6-3.8V SINE WAVE 3.2V DC 3.2V DC 3.4-4.2V 3.4-4.2V SINE WAVE 1.2V DC 1.2V DC 2.6V DC 2.4-3.0V PULSE 3.2V DC 3.2V DC 2.8V DC 2.8V DC 2.8V DC 2.5-3.0V...
Page 21
Unit[V] Ref. No. PIN STBY TALK NOTE 9V DC 0.8V 3.2V DC 3.2V DC 5.2V DC 5.2V DC 3.8V DC 3.8V DC 2.6V DC 2.6V DC 2.6V DC 2.5V DC 2.2V DC...
Page 22
Handset Unit[V] Unit[V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE 0-2.8V 1.9V DC 0V DC 0V DC 0-2.8V 1.9V DC 1.4-3.0V 3.0V DC -0.2-2.6V 1.6V DC 0V DC 0V DC 0.4-0.8V 0.6V DC 3.0V DC 3.0V DC 0.4-1.5V 1.5V DC...
Page 23
Unit[V] Unit[V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE 0V DC 0V DC 0-0.4V 1.0V DC 3.0V DC 3.0V DC Q601 0-2.0V 1.9V DC IC603 3.0V DC 3.0V DC 0-1.0V 0.3V DC 3.0V DC 3.0V DC 0V DC 0.7V DC 3.0V DC...
PARTS LIST PRODUCT SAFETY NOTE : Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don't degrade the safety of the product through important servicing. Symbol Symbol 30 -20+80 0+100...
Page 35
LOC. REF. PART NO. DESCRIPTION RC005202 BCML311045Z CERAMIC M/L (1608) 0.1UF 16V K B RC004369 BCDR811096Z ELECTROLYTIC 1UF 50V M C-292 RC002234 BCXT814735Z CERAMIC M/L (2125) 0.047UF 50V K B RC008485 BCMM813914Z CERAMIC M/L (1608) 390PF 50V J CH RC009372 BCML511835Z CERAMIC M/L (1608) 0.018UF 25V K B...
Page 36
LOC. REF. PART NO. DESCRIPTION RC005216 BCMM813304Z CERAMIC M/L (1608) 33PF 50V J CH RC000744 BCKB811025Z CERAMIC 0.001UF 50V K YB(B) RC005202 BCML311045Z CERAMIC M/L (1608) 0.1UF 16V K B RC005202 BCML311045Z CERAMIC M/L (1608) 0.1UF 16V K B RC008146 BCML816825Z CERAMIC M/L (1608) 0.0068UF 50V K B...
Page 37
LOC. REF. PART NO. DESCRIPTION C643 RC005223 BCMS812091Z CERAMIC M/L (1608) 2PF 50V C CK C644 RC005401 BCXT111055Z CERAMIC M/L (2125) 1UF 10V K B C645 RC005202 BCML311045Z CERAMIC M/L (1608) 0.1UF 16V K B C646 RC005205 BCML811035Z CERAMIC M/L (1608) 0.01UF 50V K B C647 RC005202 BCML311045Z...
PACKING BAG(PORT.) MIRA MAT RC009344 WSLV444958Z SLEEVE ASSEMBLY PARTS LIST NOTE: Following part numbers are not available as replacement parts. Order parts necessary for repair or contact the Toshiba Factory Service Center. LOC. REF. PART NO. DESCRIPTION RC009518 AC268BHBA BASE MAIN PCB ASSEMBLY...